Search Documents

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of' density. A serial sectioning' technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski' in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968

By F. L. Bosqui

The history of the development of gold metallurgy in South Africa is divisible into two periods: That preceding the introduction of the cyanide process on a commercial scale in 1890; and the 24 years intervening between that important event and the present time. The period between the discovery of the banket reefs of the Witwaters-rand and the year 1890 was one of phenomenally rapid progress in mining development, but of no special interest to the metallurgist, There were no strikingly original or distinctly local advances in the treatment of gold ores. Californian practice in stamp milling and amalgamation prevailed, in mills ranging in equipment between 5 and 50 stamps, operating within a wide range of efficiency, and under the trying conditions usually encountered in a new and isolated field. The somewhat incomplete records of gold output of that period show that in December, 1887, there were 20 producing companies in the Witwatersrand district, of which 10 had mills, the largest being of 20 stamps. The only official record of returns for May, 1887, was that of the Wemmer mine, whose modest achievement with a 5-stamp mill was 100 tons crushed, producing 887 oz. 3 dwt. of gold. This is interesting in view of the present-day output of this field, which in 1913 reached 8,430,998 oz. The rapid increase of production during this first period (May, 1887, to January 1891) is shown by the following summary for the year 1890:1 Total tone crushed.................................. 702,828 Number of stamps in operation....................... 1,046 Average number of tons crushed per stamp per day..... 2.36 Yield of gold, ounces................................ 494,817 Yield per ton, pennyweights.......................... 13.36 The stamp duty ranged between 11/2 and 4 tons per day, according to weight of stamp, fineness of screen, and operating skill available. The prevailing weight of stamp was about 900 lb., and the screen, 900 meshes to the square inch.

Jan 1, 1916

By Robert Mehl

THE purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2° C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsen1 that variations as great as 30° C. exist in the reported data on the A3 temperatures in iron-carbon alloys. For-tunately, the A3 temperature in pure iron is now known to be 910° C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato' on both hypoeutectoid and hyper-eutectoid steels.

Jan 1, 1937

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

By Wllliam D. Davis

C OMMERCIAL production of oil in northeastern Oklahoma began in 1897 and in the next two decades this area became one of the greatest oil districts of the time. Its importance is now secondary, but thousands of wells in this area have produced uninterruptedly for more than thirty years. They are now classified as stripper wells. By means of what is known as water flooding their L. production can be considerably in- creased. This practice consists in injecting water under pressure into the sand surrounding an oil well, thus displacing the oil in the pores of the sand and forcing it into the oil well.

Jan 1, 1940

By William M. Shepard

The Tintic mining districts of central Utah com- prise one of the major silver-lead producing areas in the United States. Ore valued at nearly $450 million has been produced from these districts since the initial discoveries, in 1869, of veins cutting the Silver City monzonite stock. Subsequent production from the famous manto-type "ore runs", which characterize the Main Tintic district, was followed during the past 40 years by discovery of the blind orebodies of the East Tintic district, including the famous Tintic Standard mine and the most recent discovery, the Burgin mine, currently being brought to full production by Kennecott Copper. The occurrence of blind orebodies of exceptional size and grade in both the Main and East Tintic districts has made this area a field laboratory of major importance for the study of geochemical dispersion halos and alteration features associated with known ore, and has led to the discovery of additional concealed orebodies. The larger share of the basic data-gathering and interpretation has been done by members of the U.S. Geological Survey who have been studying the Tintic mining areas since before the turn of the century. These studies have been supplemented and expanded by the geological staffs of the local operating mining companies, by exploration geologists and by students.

Jan 4, 1966

By Arthur L. Walker

In June, 1893, while I was with the Old Dominion Copper Co. at Globe, Ariz., I received an offer to take charge, as manager, of the Baltimore Electric? Refining Co. which had recently built a plant at Baltimore, Md., having a capacity of about 1200 tons of electrolytic copper per month, using the Hayden series system. This was a very large output, for in those days the plants were small and the art was in its infancy. At the beginning of 1893 there were 11 electrolytic refineries in the United States, most of them using the multiple system. The Hayden series system was used at Baltimore and Bridgeport and the Smith series system was in operation at the Electrolytic Copper Co. at Ansonia, COM., and at the Pennsylvania Salt Co. at Philadelphia. In the latter system the plates were placed in a horizontal position, but the operating difficulties were so numerous it was soon discarded. The total production of these 11 plants in 1892 was very small; I have not been able to discover reliable figures of production. There were about thirty electrolytic copper refineries in the world that year, according to Titus Ulke, and the entire production of these

Jan 1, 1932

By C. A. Heiland

MEASUREMENTS of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for com-prehensive engineering information on the subject. The working principles of a number of gravimeters will be, illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as ele-mentary form as possible. A description of calibration methods con-stitutes the last part of the paper. The symbols shown at the top of page 2 will be used in equations throughout the paper.

Jan 1, 1939

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep under-ground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county pro-vides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest com petitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955

By Samuel Taylor

IF I LIVE another fourteen months and am still con-nected with the coal industry, I shall then have com-pleted a half century with it. Since May, 1874, when .I first entered the bituminous workings as a miner, I think I have held almost every position connected with a mine except possibly that of mule driver, for which I was unfitted by reason of my religious upbringing. We are all agreed, at least I have not heard it contra-dicted, that there is serious over-production in the bituminous industry. This has come about in various ways and is easily explained. During the Fuel Admin-istration, I recall making an estimate of the possible output of the bituminous mines of the country provided they were given a full force of men and a full-car supply; my estimate was a little over a billion tons a year. A few months ago, the late Francis H. Peabody, of Chicago, made a practically identical estimate. If, however, both of these conditions should happen con-currently, there would very soon be no market for the coal, and many of the mines would close down. Even today, if 10 per cent. more cars were furnished, to the bituminous mines, market prices would drop very seriously.

Jan 4, 1923

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By S. H. Williston

IT not often that bore hole surveys can be checked by actual. civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bis-bee, Ariz., drilled a 1245 ft, 8 in. diarn, churn drillhole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Because of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results of doubtful value. Sperry-Sun gyroscopic well-surveying instruments were finally used to locate the bottom of the hole. These instruments consist of a gyroscope to determine azimuth and either a pendulum or bubble inclino-meter. A multiple shot camera photographs both instruments on a single film and superimposes the photograph of a watch. Coordination of depth with time at the surface makes it possible to select the corresponding picture for any depth. After making several runs of the empty instrument housing from the top of the hole to the bottom to make sure there were no obstructions in the hole, three surveys on wire line were completed during the afternoon. The three surveys, in which readings were taken at different points in the hole on each survey, were computed and gave the following locations of the bottom of the hole in relation to the surface collar: survey No. 1—24.92 N, 30.30 W; survey No. 2—24.24 N, 31.11 W; survey No. 3—26.54 N, 27.72 W. Then the data from the three surveys were combined into a single set of calculations which gave a location for the bottom of the hole: combined surveys—24.27 N, 30.16 W. (Fig. 1.) Immediately upon the determination of the coordinates at the bottom of the hole, a drift on the 1300 ft level was started toward the indicated loca- tion some 38 ft northwest of the coordinates of the surface location, The bottom of the hole was located within the drift round in which it was expected, and the transit survey run to the actual location of the hole indicated N 27.18, W 29.71. This shows a discrepancy between the well survey and the transit survey of 0.45 ft in the westerly direction and 2.91 ft in the northerly direction. All surveys, both gyroscopic and transit, fell well within the width of an ordinary drift. While this is satisfactory for almost any and all mining requirements, a theoretical examination was made as to reasons for the discrepancy. A study of the course of the hole indicates that considerable right turn or spiral existed, and in all probability the surveying instrument was pulled out of alignment while traversing the turn by approximately 0.05 ft at the top and another 0.05 ft in the opposite direction at the bottom of the instrument. If such an allowance were to be made, the survey calculations would almost exactly correspond with those determined by transit. This sort of discrepancy would be minimized by the use of stabilizing guides. It is unfortunate that physical laws probably effectively prevent the use of gyroscopic instruments in EX and AX diamond drill holes. The directive power of a gyroscope falls off inversely at some rate between the third power and the sixth power of the diameter. Present instruments can be run in casing 53/4 in. ID or over and might be adapted to somewhat smaller diameters, but the difficulty of reducing these diameters to 11/4 in. or 2 in. is almost insurmountable at the present time. Acknowledgment The author wishes to express his appreciation to the Phelps-Dodge Corporation for permission to publish this article, and to the Operating and Engineering Departments for their cooperation on the survey; also to Donald Hering, of the Sperry-Sun Well Surveying Co., who actually made the survey and calculated the results.

Jan 1, 1951

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By A. L. Mular

lnput energy-size modulus relation at small reduc-tion ratios is expressed by Et = (M, -Mt) k;. In some cases 13 is close to Schuhmann&apos;s distribution modulus a in value. Experimental results in conjunc-tion with the equation demonstrate the fact that energy input which produced fracture is not expended on unbroken starting material inside the mill at any time. Recently, schuhmann1 derived the Charles equation2 using the postulate that complex com-minution operations can be considered as a summa- tion of many comminution events. The fragments resulting from each event are assumed to follow the Gaudin-Schuhmamn distribution. In his derivation, Schuhmann implies that the size distribution of the total mass of a material is determined by the fraction of that mass actually subjected to comminution. Consider a feed to contain a volume, Vo, of uni- formly sized homogeneous material. After t seconds of grinding, let the volume of broken material be Vo - Vt where Vt is the volume of starting material not yet broken. The size distribution of the broken material is given by: where V is the cumulative volume less than size X, and k, is the size modulus of the broken material at time t. The distribution for the total volume at this

Jan 1, 1962

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. &apos;rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938