Search Documents

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Hans Conrad, W. D. Robertson

FORMAL theories of yielding and flow have been developed to describe thermally activated plastic flow in metal crystals.'-" hey are all based on Becker's' original idea that thermal fluctuations aid the applied stress in overcoming internal barriers to flow and lead to the following relation. where j is the strain rate; C is a constant which includes a frequency factor, the entropy, the number of flow units, and the amount of strain associated with each successful fluctuation; E(T) is the activation energy associated with flow, and is a decreasing function of the applied stress, 7; k is Boltzmann's constant; and T is the temperature in OK. The various theories differ mainly in the model chosen and in the nature of the relationship between the applied stress and the activation energy. Beckerl and Orowan' suggest a relationship of the form E a(Ti — t)2, where .ri represents the stress required for flow without the aid of thermal fluctuations; Kauzmann,3 Cottrel1,5 and Seeger6,7 suggest E a(t — t) ; Fisher8 suggests E while Cottrell and Bilby4 suggest a more complex relationship between E and 7. Additional data are needed to test these various theories., esweciallv- in view of Dorn's9 ork. which indicates that the activation energy for creep is independent of the stress and strain. The present paper presents the stress-strain data derived from incremental loading of magnesium single crystals in tension and direct shear, in the temperature range of 78" to 364°K. Incremental loading was employed in order that the creep component of the strain could be determined. Stress-strain curves of aluminum10-13 and copper" single crvstals. derived from incremental loading tests, have been found to be in agreement with those obtained by the more conventional constant strain rate or loading rate tests. Two types of tests were conducted in the present investigation: 1) tests in which the temperature was maintained constant throughout the entire

Jan 1, 1958

By G. Y. Chin, M. T. Dolan, W. L. Mammel

The least work analysis of constrained deformation, first proposed by Taylor and recently modified by Chin, Hosford, and Mendorf to include twinning, has been applied to the problem of axisynmetric flow. Calculations were made, for the case of (111}(110) slip and {111}(112) twinning applicable to fcc deformation. The solutions were obtained by linear programming techniques and with the aid of computer methods. The results show that in axisymnzetric tension the onset of twinning tends to decrease the plastic strength anisotropy as compared with the case of defortnation by slip alone. In compression, however, the strength anisotropy is increased as a result of twinning. The [100] and 11111 orientations and their vicinity are unfavorable for twinning in tension and compression, respecticely. With slight modifications, the present results may be applied to bcc metals deform ing by {110}(111j slip and (112} (111) twinning. Implications of present results to wire texture development of low stacking fault energy fcc materials arc discussed. PREVIOUSLY we' have applied linear programming techniques to obtain solutions to Taylor's least work analysis2 of constrained deformation of single crystals undergoing axisymmetric flow, such as occurs in an axially loaded polycrystalline aggregate. These solutions yielded values of the parameter M = o/.r = Y/w which relates the external stress-strain (u-c) curve to the shear stress-shear strain (7-y) curve for the crystal. The value of M is dependent on crystal orientation and hence enters significantly in texture strengthening considerations.3'4 Recently the Taylor hypothesis was modified by Chin, Hosford, and Mendorf' to include mechanical twinning. The latter has now been applied to the problem of axisymmetric flow and the results are reported in this paper. Calculations have been made for {111 )( 110) slip and {111 )(112) twinning applicable to fcc crystals. With minor changes in the indices of the slip and twin systems, the present results are also applicable to bcc crystals which slip on (110) (111) and twin on {112)(111) systems.

Jan 1, 1970

By William Emmons

THE problem of the metalliferous veins has always been an outstanding one in the science of ore deposits. In recent years interest has been stimulated by Spurr, who maintains that veins have consolidated from magmas that have densities as great as the densities of ordinary rocks. Lindgren published a noteworthy paper1 in 1926, in which he supports the theory that veins are deposited chiefly by hot waters. Lindgren's paper was discussed by Singewald, Spurr, Kemp, Anderson, Colony, Bateman, Porter and others. The discussion, in the main, was centered on the interpretation of fragments that are included in veins. This paper also treats the problems of fragments in veins and includes a reply to a review by Spurr2 of a bulletin by Larsen, and myself published by the United States Geological Survey on the geology and ore deposits of Creede, Colorado. Mineral veins containing fragments of the wall rock are common. At many places the fragments are completely, isolated, one from the other, and are entirely surrounded by vein matter. It has been stated that the vein matter around the fragments was heavier than the fragments and that the latter were floated in a magma. J. E. Spurr, who is the leading advocate of this hypothesis,4 urges that normal mineral veins were deposited by solutions heavy enough to float fragments of the country rock, and it is mainly on this relation that he bases his theory that veins are deposited by solidification of magmas. If it can be shown that vein-forming solutions have a specific gravity greater than rock (2.77), one is justified in regarding them as true magmatic solutions. It is shown later in this, paper,. however, that at Lead, S. D., water not more highly concentrated' than ordinary drinking water is depositing vein matter around fragments of schist and of steel in such a manner that the fragments are completely isolated and completely surrounded by the mineral cement.

Jan 1, 1928

By E. S. Machlin, Morris Cohen

The martensite reaction in single crystals and polycrystals of 70 pct Fe-30 pct Ni alloys is shown to be autocatalytic in nature, producing bursts of transformation during cooling. The temperature of the first burst of transformation, called Mb, occurs below M, in these alloys. Experiments were devised to test the athermal embryo and strain embryo theories of martensite nucleation. The results indicate that internal strains, either within the virgin austenite or around existing martensitic plates, control the nucleation process in these alloys. Furthermore, the growth of martensitic plates is not limited by the attainment of an elastic balance with the austenitic matrix, but by the occurrence of plastic deformation at the martensite boundaries which interferes with the propagation mechanism. IN an investigation of the martensitic habit in single crystals of a 69 pct Fe-31 pct Ni alloy,' it was observed that about 25 pct of the austenite transformed during subatmospheric cooling within the time-interval of an audible click. This event proved quite spectacular: The shock wave sent out from the specimen freely suspended on a thread in the refrigerating liquid was occasionally sufficiently intense to shatter the Dewar container and to separate the toluene column in the immersed thermometer. The Present investigation was undertaken to determine- the kinetics and mechanism of this "burst" type of martensitic reaction. The analyses of the alloys studied are given in Table I. The composition of the single crystal specimens is designated by alloy A, while the polycrystal-line specimens were made of alloys B and C as noted in the text. The single crystals were prepared in a vacuum furnace, using a modified Bridgman technique. Most of these crystals were homogenized by holding for 24 hr at about 1300°C just after solidification. However, it may be emphasized here that the degree of homogenization was not a controlling factor in the subsequent experiments, inasmuch as specimens having different degrees of homogenization yielded the same results. All of the single crystals were fully austenitic as slowly cooled to room temperature. An illustration of the burst phenomenon is given in Fig. 1, which shows oscillograms of electrical resistivity and temperature vs. time during the continuous quenching of 1/16 in. wire specimens (alloy B) in a dry ice and acetone bath at —77°C. There are at least two observable bursts in this case, as indicated by the sharp decreases of resistance accompanying the sudden formation of substantial quantities of martensite. The thermal arrest during the quench probably corresponds to the larger burst. Usually the bursts are followed by more or less progressive transformation during continuous cooling. It will also be noted that the resistance continues to decrease after the specimen has reached the bath temperature. This isothermal change denotes the formation of martensite at constant temperature, and will be the subject of another paper. Examination of fiducial scratches on the surface of a transformed single crystal has shown2 that the scratches in adjoining nonparallel martensitic plates are usually bent in opposite directions, as though one plate forms in such a way as to relieve the matrix stresses set up by the adjacent plate. This, together with some of the results described in ref. 1, Table I. Compositions of Alloys Studied, in Percent Alloy Ni C N Mn Si P S Cr A 31±0.3 0.048 0.027 0.003 0.56 0.007 0.002 B 29.5±0.2 0.036 0.02 0.19 0.09 0.008 0.006 C 19.99 0.52 0.37 0.47 0.010 0.015 0.04 led to the tentative concept that a cooperative action exists which provides the impetus for much of the transformation that appears during the burst. The following series of experiments were performed in order to test this idea. Cooperative Nature of the Burst Two adjacent disks, Va in. thick x % in. diam, were cut from a single austenite crystal of alloy A using a jeweler's saw. One of the disks was then cut into 15 parts. Then 12 of the latter pieces and the second disk were austenitized (stress relieved) at 600°C for 30 min and water quenched to room temperature. The temperatures at which the first burst of transformation appeared were determined for

Jan 1, 1952

By Joseph Singewald

THE problem of the utilization of the low-grade red iron-ores has peen before the iron-mining industry of the South for several decades. the experiments by W. H. Coghill1 of the U. S. Bureau of Mines to determine the degree of liberation of minerals in the Alabama low-grade red iron-ores after grinding interest the writer very much because 10 fears ago, while a member of the U. S. Bureau of, Mines, he experimented similarly on the same ores using a heavy solution .2 Extensive experiments were made in the nineties by W. B. Phillips3 in association with H. A. J. Wilkens and H. B. C. Nitze. The ores were rushed to pass 15 mesh and were separated by magnetic machines into concentrates, middlings and tails. The experiments were made with carload lots in an experimental mill. Most of the ores tested, however, were soft, whereas the main problem is the utilization of the low-grade hard ores. Phillips gives the results of only four tests of hard ores; two of these are of self-fluxing ores of the grade now utilized and two of ower grade and less amenable to concentration than the average low-grade ore that underlies the self-fluxing ore of the Big Seam. The average of these least favorable samples shows the production, from an ore analyzing 32.30 per cent. Fe, 10.34 per cent. CaO, 33.40 per cent. insoluble, of a concentrate with 43.82 per cent. Fe, 8.90 per cent. CaO, 18.48 per Sent. insoluble with a ratio of concentration of 2 and an iron recovery of 39.2 per. cent. The grade of this concentrate compares favorably with the average grade of washed brown ores of the district which is given by Burchard4 as 45 per cent. Fe, 14.6 per cent. Si02. The slightly lower iron

Jan 2, 1927

By Charles Bohdanowicz

The accompanying tables' show that in 1936 production of crude oil in Poland decreased very slightly (Tables 1 and 5), by about 1 per cent, and that gas production increased by about 11 per cent. As in preceding years, drilling (Tables 1, 2 and 3) was devoted principally to extension of oil fields in the Jaslo district (fields 1, 5 and 7) and, in a lesser degree, of those in the Stanislaw6w district (field 27). Production of crude oil is being sustained in a large measure by the deepening of old wells; besides a total number of 183 new wells completed (Table 3) about 152 wells were deepened, and in a general way the results of deepening were better than those of new wells drilled. Reserves of "proved land" have not increased as far as crude oil is concerned, but a notable extension of gas fieldsZ was attained in Daszawa (field 25) and in the Roztoki area (field 5). In the sub-carpathian zone gas fields have been proved in the vicinity of Kalusz, Kos6wJ and in the northwestern sector of that zone, between Tarnow and Lezajsk. The gas horizons of Daszawa occur in the Upper Tortonian, those of Kos6w in the Lower Tortonian (Middle Miocene). Exploratory drilling has been performed near Kalusz, and has been commenced near Kos6w and in the Tarn6w area. The Kos6w gas approaches the "wet" type. A possible gas reserve with a volume of 4,000,000,000 cu. m. (141,000,-000,000 cu. ft.) has been calculated, for an area of about 5 sq. km. of the Daszawa field, on the basis of production obtained and of decreases in pressure and their distribution. The fields of Roztoki and Strachocina (No. 12) have not yet supplied sufficient data for a calculation of reserves, which might possibly be estimated at 2,000,000,000 cu, m. (70,000,-000,000 cu. ft.).

Jan 1, 1937

By B. E. Thompson, H. B. Fuqua

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area, and the general geological features with which it is associated, the reader is referred to the opening paragraph of last year's summary1. A more complete discussion of the structure of the area, together with other interesting data concerning it, has been published recently by the Bureau of Economic Geology at the University of Texas2. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by operators except by counties or arbitrary divisions of counties. The total number of wells drilled in Archer, Wichita and Clay counties also has been subject to some estimate, as many of the shallower holes are not reported. While both routine development in proven or semiproven areas and exploratory drilling during 1935 showed an increase over the year 1934, the discovery of new producing areas of importance did not show improvement over that period. Several extremely local productive spots within semiproven areas were found in Archer, Cooke and Wilbarger counties; and extensions to older producing areas were developed in Archer, Baylor, Cooke, Montague, Wichita and Wilbarger counties. In Archer County, the Grace and Woods No. 1 Archer County (Fee), 4 miles northwest of Archer City, in the Thomas Glass survey, encountered a sand from 2836 to 2845 ft. of Pennsylvanian (lower Canyon) age, which showed an initial yield of 75 bbl. daily. While its production is of negligible importance, it is given special mention in this review because of the fact that it is producing from a new and deeper horizon than has been previously exploited in the county. Little deep development occurred in the district during the year. The Walter Gant No. 2 C. M. Worsham in J. M. Swisher survey, about 14 miles east of Henrietta, in Clay County, was abandoned at 5127 ft. in

Jan 1, 1936

By James D. Sisler

Among the various studies made by the Coal Fact Finding Commission, appointed by President Warren G. Harding in 1922 to investigate all phases of the coal-mining industry in the United States and to report to Congress, was one concerning the amount and nature of losses in mining bituminous coal in the eastern part of the United States. This study was carried on under the direction of the U. S. Bureau of Mines. The writer was appointed field engineer to investigate the problem in Ohio, Pennsylvania and West Virginia. Some 400 mines were studied in these three states and conclusions were drawn from many sources of data. The summary report written by George S. Rice and J. W. Paul states that "the field reports indicate that the recovery in Ohio will remain about as at present, except in the Belmont district; whereas in Pennsylvania it will gradually improve, and in West Virginia it will improve rapidly." Since 1922, the writer has been interested in gathering material to substantiate or contradict these prophecies. Nature of Coal Losses There are six general causes of losses of coal in mining: (1) coal left on the roof and bottom; (2) coal lost in room, entry and panel pillars; (3) coal lost in oil-well or gas-well pillars; (4) coal lost under buildings, railroads and boundaries; (5) coal lost in handling and prepayation, underground and surface; (6) coal lost by rolls, thin or dirty areas and under streams. Local economic aspects that dominate the type of mining conditions determine to some extent whether certain losses are avoidable or unavoidable. In general, however, unavoidable losses include coal lost in the protection of buildings, streams, railroads, restricted properties and around oil and gas wells. Barrier pillars and other safety pillars are unavoidable losses as long as their size does not exceed the minimum for adequate safety. Natural physical conditions beyond human control, such as rock faults, clay veins, partings and binders, bad top and bottom, rolls and horsebacks, cause unavoidable losses. Unavoidable losses

Jan 1, 1931

By George R. Mansfield

INTEREST in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lakeland, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.1 At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern producers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This information has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,2 some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,3 of the Tennessee Division of Geology. Prof. J. Stewart Williams,4 of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered. Technologic advances in the phosphate industry must be credited with a large share in the expansion of reserves by making available for

Jan 1, 1940

By G. C. Kuczynski

A. J. SHALER* and H. UDIN*— Bonding, and the increase in contact area, form two of the series of phenomena collectively known as 'sintering.' A third one of these is involved in changes in dimensions of the whole compact. Dr. Kuczynski's Fig 1, in which the center of the sphere does not approach the surface of the plate, shows that he is not concerned with the last of these phenomena. On the other hand, Frenkel's work is exclusively concerned with changes in dimensions. Dr. Kuczynski's rather unfortunate remarks about Frenkel's work are therefore beside the point. The work of Wulff and myself, quoted by the author, has also been primarily concerned with what we call the 'second stage of sintering,' in which such systems as may be represented by Kuczynski's model of a sphere and a block are no longer in existence. The work of Pines also falls in this category. Neither does Dr. Kuczynski's very masterful experimental work represent a solution to the problem of bonding. It does not seek to answer the question of why particles approach one another and form a weld in the first place. Such a study clearly reveals that the area of contact is initially rapidly deformed by direct mechanical flow caused by the same force of attraction. This initial deformation is neglected here. On the other hand, students of the phenomena of sintering must not underestimate the very important contribution that Dr. Kuczynski does make in this paper. It is a well-worked out study of the mechanism of 'spheroidization' of the voids, the first manifestation of which, during sintering, is the growth of the areas of contact, with no change in the dimensions of the compact. This study is very valuable as a basis for predicting the development of the strength of such compacts as filters and certain porous bearings, in which the second stage of sintering is never reached. A few more specific points may be brought up here. If, in Table 4, the data are extrapolated to zero time, it is easily

Jan 1, 1950

By Alfred H. Brooks

PetRoleUm seepages are known in Alaska at four localities, all on Pacific seaboard. These, named from east to west, are Yakataga, Katalla on Controller Bay, Iniskin Bay on Cook Inlet, and Cold Bay on the Alaska Peninsula. Besides these, a petroleum residue has been found near Smith Bay on the north Arctic coast of the Territory. At Katalla, Cold Bay, and Iniskin Bay there has been some drilling for oil, and in the first field several productive wells have been opened up. Alaskan petroleum, so far as its composition is known, is a refining oil, with paraffin base and low sulphur content. Most of what is known of the geology of Alaska oil fields is based on the investigations of Dr. George C. Martin, of the United States Geological Survey. A, G. Maddren, of the same service, has recently made a reconnaissance of the Yakataga oil field. The data to be here presented are chiefly taken from the following publications: G. C. Martin: The Petroleum Fields of the Pacific Coast of Alaska, with an account of the Bering River coal deposits, Bulletin No. 250, U. S. Geological Survey, pp. 9 to 27 (1905). G. C. Martin: Geology and Mineral Resources of the Controller Bay Region, Alaska, Bulletin No. 335, U. S. Geological Survey, pp. 112 to 130 (1908). G. C. Martin and F. J. Katz: A Geologic Reconnaissance of the Iliamna Region, Alaska, Bulletin No. 485, U. S. Geological Survey, pp. 126 to 130 (1912). A. G. Maddren: Mineral Deposits of the Yakataga District, Bulletin No. 592, U. S. Geological Survey, pp. 143 to 147 (1914). Katalla Field The Katalla field is marked by a series of seepages and gas springs occupying an east and west belt, about 25 miles in length and from 4 to 8 miles wide. (See Fig. 1.) This zone skirts the north shore of Con-

Jan 1, 1915

By Y. Kondo, A. M. Gaudin

A combined method for sizing in the sub-micron range was developed using centrifugation and gamma emission. Its essential features are: 1) Centrifugation of suspended mineral in water carried out at 4°C where water has its maximal density and zero temperature gradient of density 2) Gamma activition of the sample suspension induced by irradiating it in a nuclear reactor prior to centrifugation 3) Measurement of the activity of a beam of suspension as it is sedimenting in the centrifuge, using a scintillation counter provided with a discriminator. Albite, the sodium feldspar, was used as feed to the comminution step, and the induced gamma activity of Na24 was measured. Dissolved sodium ion caused a a non-settling activity in the measurement. Other "noise" is due to scattered gamma radiation from albite particles in the centrifuge outside of the line of sight. These two activities were obtained sep arately and subtracted from the total activity counted. The relative solid concentration in the suspension under the collimating slit is proportional to this net activity. The cumulative weight per cent of undersize particles was calculated and plotted against size on logarithmic scales. The relationship was found to be linear down to about 30 mµ. The specific surfaces calculated from particle size distribution agree with those measured by krypton gas adsorption. The measurement of particle size distribution of comminution products has been of interest in clarifying the mechanism of the process. The Gaudin-Schuhmann equation1,2 relates the cumulative percentage undersize, y, to relative particle size x/k. The particle size, x, and the size modulus, k, together with the distribution modulus, m, characterize the particle size distribution, m is the slope of a plot of log (y) against log (x/k). This equation has been verified for ground particles down to 1 micron in size.3'4 For particle sizes smaller than a few microns, the precision and facility of sedimentation and microscope techniques become questionable. Use of a centrifuge which shortens settling time from weeks to hours is attractive. Many centrifugal methods have been proposed; however, determination of the solid concentration of the suspension at a reference level as a function of time is difficult, and sampling the suspension is likely to introduce errors. Measurement of particle size distribution by X-ray absorption in gravitational5 and in centrifugal6 sedimentation have also been tried. In these methods, the absorption coefficient for the solid is independent of size, since the wave lengths of the X-rays and gamma-rays are orders of magnitude smaller than the particles. Radiometric techniques7 in size distribution measurement have been developed within the last several years. They offer advantages over usual gravimetric and optical methods. PRINCIPLE OF METHOD The combined method of centrifugation and gamma emission for sizing in submicron range described in the present paper has the following essential features. 1) Centrifugation is carried out at 4 ± 0.1°C. Convection currents in the water phase due to density changes caused by temperature variation may disturb completely the settling system. To avoid this difficulty, the unique property of water having zero temperature gradient of density at 4°C is used. 2) Prior to size measurement the sample suspension is irradiated in a nuclear reactor and gamma activity induced. The gamma activity of the particles sedi-mented radially is measured by a scintillation counter provided with a discriminator. By this method, interruption of centrifugation by withdrawing samples is avoided and the counting rate at any time represents the solid concentration in the suspension at the level of the collimating slit of the centrifuge at the particular time at which the measurement is made. 3) By proper selection of the feed material and of the comminution device, gamma activities of foreign

Jan 1, 1964

By J. W. Powell, F. H. Spedding

A complete review of the use of chelating agents in the sepa ration of rare earths by ion-exchange is given as well as a concise description of the recent pilot-plant operations of the Ames Laboratory. The two chelating agents which show the greatest promise are ethylenediamine-N,N,N',N'-tetraacetic acid and N'-(2-hydroxyethyl)ethylenediarnine-N,N,N '-triacetic acid. The first successful separations of rare earths by ion exchange were reported in a collection of papers which appeared in the November, 1947, issue of the Journal of the American Chemical Society.1'9 Some of this work was performed at the Ames Laboratory of the A.E.C., the remainder at the Oak Ridge National Laboratory. The processes developed at Oak Ridge, as well as some of the early Arnes methods, employed 5 pct citric acid-ammonium citrate eluant at low pH and were carried out on either H+-state or NH:-state resin beds. These techniques were successful for the separation of small quantities of either naturally occurring or radioactive rare earths and are still used for the isolation of rare-earth activities from fission products. Concentrated citrate is not economical, however, for use in moderate or large-scale rare-earth separations. For this reason, the Ames Laboratory turned its attention to lower concentrations and higher pH's in order to make more effective use of the eluting agent.10-14 Although elutions have been performed successfully over a wide range of conditions, 0.1 pct citrate at a pH of 8.0 is highly recommended for use on H+-state resin beds.15,16 Elu-tion with 0.1 pct citrate in the pH range from 5 to 9 brings about the separation of the constituent rare earths into a series of flat-topped elution bands which progress down the resin bed, head to tail, without actually pulling apart as do the rare-earth peaks which develop when trace quantities are eluted with 0.25M (5 pct) citrate at low pH's. Because of this, elution with 0.1 pct citrate at pH 8.0 do not produce pure rare earths unless sufficient quantities are present to provide developed bands which are at least several inches long on the columns. Although other eluting agents have proved more effective than citrate solutions, articles concerning the use of citric acid for separating rare earths still appear in the literature occasionally. For example, Ketelle and Boyd17 reported some further studies on the separation of rare earths with 5 pct citrate in 1951. They used 270 to 325 mesh Dowex-50 columns at 100°C and a pH of 3.28. vickery18 compared the effectiveness of a number of eluants for the separation of rare earths on NH+4 state Dowex-50 in 1952. He found that citric acid was more efficient than acetic, malic, tartaric, and aminoacetic acids. In 1953, Mayer and Freiling18 reported that citrate was inferior to malate, glycolate, lactate, and EDTA for the resolution of Sm-Eu and Y-Tb mixtures on 250 to 500 mesh, NH+4-state, Dowex-50 at 87°C. pinta20 used 5 pct citrate in the pH range 2.8 to 3.4 to obtain some rare earths for analytical work the same year. Trombe and Loriers21 reported the use of citric acid in their laboratory to separate rare earths in kilogram quantities. Lariers and Quesney22 reported some separations with citrate in 1954. They used 5 pct citrate at pH 2.8 to separate yttrium and the yttrium-group rare earths from the cerium-group rare earths. briers23 used 5 pct citrate at pH 3.2 and 90°C as late as 1956 to isolate thulium in fair purity. For the separation of tracer quantities of rare earths, Mayer and Freiling19 have recommended pH 5.00, 0.24M lactate at 87 °C on 250 to 500 mesh, NH+4-form Dowex-50. Freiling and Bunney24 have also employed lactic acid for the separation of fission-product rare earths. Cunninghame, Size-land, Willis, Eakins, and Mercer25 have reported a 4-hr separation of Y, Eu, Sm, Pm, Nd, and Pr with 1M lactic acid at pH 3.25 on Zeokarb-225 at 87°C. Stewart, et al.,26 reported separation factors for rare earths distributing between Dowex-50 and 0.25M glycolic acid. stewart27 also reported a 30-61 separation of Y, Tm, Er, Tb, and Lu tracers with buffered, 0.25M glycolic acid containing 0.05 pct Aerosol OT. The resin bed was 400-mesh Dowex-50 (X12). The pH of the ammonia-buffered eluant was 3.5. Various aminopolyacetic acids have also been used to obtain varying degrees of separation of the rare earths. In 1951, Fitch and Russell28 investigated iminodiacetic acid (IDA) and nitrilotriacetic

Jan 1, 1960

New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 3, 1915

By William F. Boericke

RESEARCH in the modern refractories laboratory has two practical ends in view-to develop refractory materials for the metallurgist that will meet particular operating difficulties more effectively and to ?manufacture these refractories at a cost sufficiently low to make their use economical to the metallurgist. At the research laboratories of E. J: Lavino and Co., at Plymouth Meeting, Pa., the technical staff, under Dr. Gilbert E. Seil, is giving principal attention. to an. exhaustive investigation of the following factors in refractories:

Jan 1, 1931

By S. E. Clay

In the chemical reaction control regime employed in the laboratory dissolution experiments, calcined trona ore dissolves in aqueous solutions according to a first order, irreversible reaction rate. The study showed that the reaction is first order with respect to solution NagCO3 concentration. The activation energy was determined to be 20.233 kJ/g. mol with a rate constant equal to 1235 mm/s (2917 in. per min). The dissolving particle may be described by shrinking particle behavior.

Jan 1, 1986

For $100 a month plus expenses, Thomas A. Edison in 1879 hired a colorful adventurer named Frank McLaughlin to go west as a prospector. A few months later, McLaughlin triumphantly returned to the inventor's laboratory in Menlo Park, N. J. "On his shirt bosom and fingers sparkled glittering stones," recalled one of Edison's associates. These were only the tangible parts of his new trappings. In addition, McLaughlin "now wore the title of major which he acquired somewhere west of Omaha."

Jan 10, 1961

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911