Search Documents

By Roscoe C. Clark

A study of the effect of various corrosive waters on five different types of cements indicated that those cements containing less than 5 per cent tricalcium aluminate were the most resistant to corrosion. INTRODUCTION Oil field experience indicates that some formation waters are excessively corrosive to some cements. A study has been made to determine the most corrosive waters and the relative resistance of various types of cement to these corrosive waters. PROCEDURE This study of the corrosion of cement was limited to an evaluation of the effect of various corrosive waters on five different types of cements. A determination was made of the types of cements which offer the greatest resistance to corrosion and of the chemical contents of waters found to be the most destructive to cements. The laboratory tests were conducted by immersing small cylinders of 20 samples of set cement in various corrosive waters. The initial mixing of most of the cement slurries was done using Tulsa tap water as the mixing water; however, a few of the slurries were mixed using a sulfate water as the mixing water. When the 20 samples had been immersed for a period of nine months, they were removed from their corrosive baths, inspected and photographed. The field tests were conducted by placing ten cement specimens, each contained in a screen wire thimble, in the gas anchors of insert pumps in wells in six different fields. The specimens were observed whenever it was necessary to pull the pumps and were returned to the 1aboratory when deterioration had reached a serious state. EXPERIMENTAL RESULTS In both the field and laboratory tests the resistance of the different cements to corrosion was determined by the condition of the samples and the number of samples of each that were in good condition at the end of the immersion period. Table I lists the various cements tested in the order of their resistance to corrosion with the most resistant at the top and the least resistance at the bottom. An analysis of Table I reveals that the upper half of the table predominates in slow set and sulphate resisting cement.: (low 3CAO.A12O3 content) while in the lower half the port-land and high early strength cements are in the majority. Of the last two the high early strength cements appear to offer less resistance to sulfate water corrosion. An investigation of the composition of the cements listed in Table I indicated that as a general rule the cements containing less than five per cent tricalcium aluminate will exhibit the greatest resistance to corrosion. The destructive action of various corrosive waters was compared by listing the waters in the order of those containing the largest number of samples that failed completely. These ratings are presented in Table II with the most corrosive waters listed first and the least corrosive last. Figs. 1 and 2 show the end views of cement samples which had been immersed in the baths of five per cent MgSO, water and the five per cent Na2SO4 water respectively in the laboratory. These .pictures are representative of the results obtained and present a pictorial evaluation of the corrosive resistance of various types of cements.

Jan 1, 1950

The economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.—The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By G. C. Wallick

Since the appearance of the paper, "Solution of the Equations of Un-steady State Two-Phase Flow in Oil Reservoirs," by W. J. West, W. W. Garvin, and J. W. Sheldon,' a two-fold investigation of this subject has been carried out. One objective of the investigation has been to deter-mine the feasibility of solving such problems 7on a medium-size com-puter such as the Datatron*, and the other objective has been to in-vestigate the application of such cal-culations to experimental and theo-retical petroleum reservoir research. In the first Datatron calculations, the fluid and rock properties published by West, et al, were used, together with the published equations describ-ing the system. Details of the formu-lation not given in the original paper are discussed in the Appendix to this note. Reference should be made to the subject paper for the complete equations and defintion of symbols. An unexpected result of this in-vestigation was the discovery that the linear solution published by West was in error. Thus, in addition to describing the Datatron solutions and to discussing certain numerical diffi-culties which will be encountered if one uses the published method of solution, the purpose of this note is to indicate the nature of this error. LINEAR FLOW Since the linear case requires a minimum amount of scaling, a fixed-decimal point Datatron program was written for the one-dimensional flow problem and an attempt was made to duplicate the solution described by West. In the case described, fluid was produced at a constant rate, Q, until such time as well pressure reached 0.04. Production was then continued at constant pressure. From the constants and curves given by West it was determined that the ini-tial constant production rate could be approximated by Q = 0.007. An ini-tial dimensionless time step ?t = 0.434 X 10 - "as used, and each suc-cessive time step was doubled until a value of = 0.444 was reached. This constant interval was then used for the remainder of the solution. In subsequent solutions, several varia-tions in the time schedule were em-ployed, including smaller time steps and slower rates of increase in the time steps. In all cases, almost identical results were obtained regardless of the time schedule employed. However, as described below, it was noted that the time schedule had some influence on the rate of convergence of the solutions. As a check on the accuracy of the solution, the cumulative production at each time step was calculated using the two methods described in the Appendix. Satisfactory agreement was observed with the differences in these two values of the order of two parts in 50,000. It should be noted that the mass balance check as described is of questionable value, particularly with regard to the well pressure and saturation. This is especially true in the radial solution where pressure and saturation values near the wellbore would make only a negligible contribution to the numer-ical integration. It is believed, how-ever, that such a comparison is ot value in determining the over-all accuracy of a solution. In comparing the Datatron solu-tion with that published by West it was discovered that in the later stages of depletion, the pressures near the well declined more rapidly in our solution than in the West solution, and that the limiting well pressure of 0.04 was reached at an earlier time than that originally reported. It thus became evident that it would be impossible to duplicate the production schedule described by West and a constant rate of production was maintained until the well pressure was equal to 0.0. A representative comparison of the results published by West with those obtained in this investigation is shown in Fig. 1, which is a plot of GOR as a function of cumulative recovery. These two curves should be in agreement until a cumulative recovery is reached which corresponds to a well pressure of 0.04 — for the Datatron solution, a recovery of approximately 5.6 per cent. Actually, a major disagreement is evident. Subsequent correspondence

Jan 1, 1958

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By E. A. Gulbransen, W. S. Wysong

The behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance. The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotec-tive nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance studyl, 2 of the following problems: (I) the oxidation kinetics in the temperature range of 250°to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films; and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 2 50°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide Moo3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics: time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation. The general interpretation of many of these factors has been previously discussed. Literature The oxidation of molybdenum has not been studied critically. Although many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Gulbransen." Their results showed that Moo2 is the oxide which is stable in contact with the metallic substrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Moos is no longer observed, MoO2 being the only oxide found. Hagg and Magneli6 have shown from an X ray study that the a-phase, orthor-hombic Moo3 is stable up to 1050°C. Two other phases, ß and ß with compositions close to MoO2.90 are also obtained. The formula for the 0 phase is not given but that of the ß phase is defined as Mo9O26 The 0' phase is found to be built upon a monoclinic unit cell. A ?-phase is isolated from a preparation MoO2.75 heated for 17 hrs at 670°C. This phase is

Jan 1, 1949

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

(Under this heading will be published notes sent to the Secretary of, the Institute by members or other persons introduced by members.) Development and production. Member open for engagement. Past year in war mineral field work, operation and production. Ten years' thorough experience in both subordinate and executive positions, gold, silver and copper in the United States, Mexico, and South America. Age 37, married. Minimum salary $3600. Interview. South or East. A-577. Engineer and executive. Captain U. S. Army, age 36, expects discharge before July 1. Seven years' mining and metallurgical experience. Six years with large technical college as assistant professor of mining and directing extensive experimental work. Desires position as executive or research engineer with reliable company or as professor of mining with first-class college. A-909. Mining engineer. Twenty-five years' experience including mine and works operation, construction, plant installation, and mine examination. Speaks Spanish. A-1173. Metallurgical engineer. Twelve years' laboratory and operating experience, covering copper blast furnace, roasting, reverberatory smelting and latest Cottrell treater practice on copper dust and zinc dust. Technical graduate. 36 years of age, married. Highest recommendations. Open for immediate engagement. A-2354. Mining engineer. Junior Associate. At liberty about July 1. Captain Heavy Artillery. Single, age 24. Go anywhere. Best refer-ences. A-2843. Engineer. Age 26, single, graduate Missouri School of Mines, B. S. in Mis. Met. E. Desires position with oil or metal company in any capacity. Location immaterial. At present engaged, desires change. A-2844.

Jan 7, 1919

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

Industrial Preparedness To Cooperate with the U S War Department General Committee ARTHUR S DWIGHT, Chairman H FOSTER BAIN C K LEITH J EDWARD SPURR H. S MULLIKEN Alternate GEORGE OTIS SMITH POPE YEATMAN

Jan 1, 1923

OFFICERS AND DIRECTORS President and Director AUGUSTUS B KINZEL, '60, New York City Past President and Director GROVER J HOLT, '59, Ishpeming, Michigan President-elect and Director HOWARD C PYLE, '61, Los Angeles, Calif

Jan 1, 1958

[Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICHARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant]

Jan 1, 1936

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall's statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949