Search Documents

By Francis Lucas

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or-under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black, oxide that cannot be absorbed by the metal.

Jan 1, 1927

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By C. Dirksen

This study investigates whether oxygen consumption during segregated forward combustion may be affected by natural convection. Linear theory indicates that thermal instability occurs in a horizontal porous medium when the modified Rayleigh number N 'Ra exceeds a critical value of about 40. Most experimental results, including those described here, indicate this value to be about an order of magnitude smaller. N ', is derived from "differential similarity" and the proper time scale factor is also obtained. The critical value of N'ra for a horizontal, water-saturated porous medium at atmospheric pressure subjected to a uertical temperature gradient was found to be about 3.0. The ambiguity in the value of N'R, arising when fluid properties cannot be assumed constant is indicated. Natural convection was observed for oblique systems below N 'Ra , while simultaneous horizontal flow did not affect N Racrit. The expected range of values for the various parameters pertaining to segregated forward combustion is indicated and the corresponding values of N 'Ra calculated. Only under very favorable conditions, such as high permeability, high pressure and low top temperature, can the critical value of N 'R, be exceeded. Thickness of the convection layer should not become too large, since the time required to obtain significant mixing is proportional to the square of the thickness. For an oblique combustion frant the conditions for significant mixing may be less strenuous. LNTRODUCTION Laboratory1,2 and field314 experiments have shown that a markedly upgraded oil can be produced by in situ forward combustion. Under certain conditions injected air may move through a high permeability, gas-saturated channel over the oil-saturated layer, while combustion takes place, exclusively, at the horizontal interface (Fig. 1). Such a channel may be a natural gas cap, or it may result from a forward combustion process in which injected air and combustion gases fingered through the top of the formation, causing a premature breakthrough at the production well. In this particular case of segregated forward combustion, the air stream moves parallel to the combustion front. Molecular diffusion and transverse mechanical dispersion will be insufficient to cause all the oxygen in the air stream to reach the combustion front. When the oxygen in the air stream is not completely consumed in the combustion process, it will reach the production well and create a serious fire hazard. In addition, the reduced efficiency may make the process economically unprofitable while also serious corrosion problems may be experienced in the production we11.3 This undesirable situation should, therefore, be prevented. However, in a situation as depicted in Fig. 1, an unstable temperature gradient exists in the gas phase. The combustion is taking place at the lower boundary at a nearly constant temperature that may be anywhere from 600 to 1,200F, depending on the conditions. The upper boundary of the gas phase is overlying, impermeable rock; its temperature might be around 100F, but may increase to 300F or higher due to conduction and convection as the combustion process continues. This represents a steep temperature gradient and it is conceivable that under those conditions free or natural convection will take place in the gas

Jan 1, 1967

By W. R. Hibbard, Ming-Kao Yen

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

An analytical method has been developed and used in batch and continuous tests to provide initial insights into the effect of soluble calcium ion in anionic flotation of silica from iron ores. A deficiency or excess of calcium ion in pulps subjected to this type of flotation produces an impairment in flotation efficiency. Data developed in the investigation are from a single ore, but show that total calcium requirement is met from water, ore and reagent sources. In batch studies, starch additions were shown to exert no influence on the calcium level, but fatty acid and sodium hydroxide had subtractive effects. The investigation was next extended to continuous flotation testing where the general observations from batch testing were confirmed. Factorially designed experiments were performed showing that the relationship of calcium additions to flotation response was not a simple one, but tended to shift to higher additions with increased fatty acid. Nevertheless, the range of soluble calcium levels measured remained fairly constant in areas of good flotation response. It is concluded that techniques developed should be useful in removing empiricism from flotation operations in this and other systems requiring activation for success. Further development should aid in process control both through methods outlined and through investigations aimed at studying the effects of other soluble reagents. Of the major mineral commodities, iron ore was one of the last to succumb to flotation processing. Commenting on this fact, one of the speakers 1 at the convention celebrating the 50th Anniversary of flotation in the U.S.A., said ". . . in 1951 froth flotation as a means of beneficiating nonferrous minerals was a might giant and could be characterized by &apos;you name it, we float&apos; - but not iron ore". This tardiness in applying flotation to iron ores was the result of a number of factors, including economics and ready availability of direct shipping ores. Even now, when the need for beneficiation can no longer be denied, proposals for flotation of iron ores are apt to be viewed with some misgivings. This disquiet results from knowledge that wide variability, which would necessitate corresponding adjustments in reagents, often exist within even a single ore deposit. Coupled with ore variability is the fact that, at present, there is no way of quickly and precisely anticipating the direction and magnitude of reagent changes required for uninterrupted production of acceptable concentrates. Despite the long delay, iron ore flotation is now practiced commercially, although the chief applications2-4 are to specular hematites having relatively coarse liberation and low slime content. In addition, the application of flotation in upgrading magnetic concentrates seems assured. However, these flotation methods do not appear applicable to substantial tonnages of fine grained, earthy, and frequently more complex semitaconites and nonmagnetic taconites. The U.S. Bureau of Mines, in devoting its attention to the semitaconite and nonmagnetic taconite class of materials, has demonstrated that anionic flotation of calcium-activated silica can be utilized with an expected high frequency of success.&apos; Even so, it has been recognized that the flotation method is a complex one, and that the reagent suite must be carefully tailored to the feed. These conditions would be expected to offer difficulties in treating ores with the wide range of variability previously discussed. Accordingly, research was initiated to develop methods to remove much of the empiricism from the flotation operation by measuring the reagent variables within the pulp for a correlation with flotation response. A simple illustration of the technique sought would be in the well established use of pH meters to provide feedback control to reagent feeders and thereby limit acidity or alkalinity to a range producing optimum results. The first efforts in this area have been concerned with measurements of soluble calcium ion. Bureau experience in both laboratory and pilot plant over the past five years has proved that the amount of calcium

Jan 1, 1965

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By DOOLITTLE E. M.

(Canal Zone Meeting, November, 1910.) The following notes are contributed, not with the idea of offering a complete history of the development of this very important process as applied to the Leadville district, but with the hope that the practice, as it was carried out in the Bi-Metallic Smelter, may still be of interest to others. The Bi-Metallic Smelter, at Leadville, Colo., was the first to make a commercial success of the process described in the following pages, which consisted essentially of smelting raw silver- and copper-bearing sulphide ores in blast-furnaces to form a matte, which was generally re-smelted with siliceous ores for a second high-grade matte. Robert Sticht, in his excellent monograph on the subject,1 has outlined briefly the plant belonging to this company. He says, in effect: The Boulder, Mont., enterprise set the example for others with whom the patentee (w. L. Austin) had been negotiating, and the old La Plata lead-smelter at Leadville, Colo., was fashioned into a crude, temporary experimental plant for the Bi-Metallic Company, and the feasibility of the process demonstrated by a trial run. Subsequently, the plant was considerably improved, and, being supplied with very favorable ores, continued to run without interruption from August, 1892, to June, 1893. In September, 1893, smelting was resumed in a completely remodeled establishment, some $200,000 having been expended upon the new work. Thus, aside from the Montana experiments, which, under the direction of W. L. Austin, began as early as- 1885 2 at Toston, and continued with indifferent success for six or seven years, the Bi-Metallic plant at Leadville may be said to have * Formerly Superintendent, Bi-Metallic Smelting Co. + Formerly Chief Assayer and Chemist, Bi-Metallic Smelting Co. 1 Modern Copper Smelting, E. D. Peters, 7th ed., p. 415 (1895). 2 Trans., xvi., p. 259 (1887-88).

Dec 1, 1910

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. However, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers&apos; Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio&apos;s, and in 1876 by Maryland&apos;s. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

By C. S. Smith, L. W. Kempf, C. S. Taylor

The thermal conductivity of aluminum alloys is of considerable industrial importance. This is particularly true in such applications as internal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determination, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some .knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz&apos; as applying to metallic elements and later shown by Lorenz2 to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance. Literature on Thermal Conductivity of Aluminum Alloys Masumoto3 determined the electrical and thermal conductivities of 18 aluminum alloys. His results indicated a relatively constant relationship between thermal and electrical conductivity.

Jan 1, 1937

[Contents AH-Metal Mining and Industrial Minerals Pipeline Transportation of Phosphate. (Paper by I. S. Tillotson, R. B. Burt, and J. A. Barr, Transactions AIME, 193, 273; Mining Engineering. March 1952. Discussion by Howard Howie.) 1066 B-Minerals Beneficiation The Effect of Zinc Deleading Operations on Lead-Zinc Selectivity at the Parral and Santa Barbara Mines. (Paper by C. L. Boeke an G. C. Gunther, Transactions AIME, 193, 495; Mining Engineering. May 1952. Discussion by I. M. Symonds, L. H. Lange, Norman Weiss, H. S. Wildman, C. F. Zeuch, E. H. Crabtree.) 1067 Jaw Crusher Capacities, Blake and Single-Toggle or Overhead Eccentric Types. (Paper by D. H. Gieskieng, Transactions AIME, 190, 971; Mining Engineering. November 1951. Author s supplement.) 1069 Screened Ore Use for Fine Grinding at Lake Shore Mines. (Paper by Bunting S. Crocker, Transactions AIME, 193, 499; Mining Engineering. May 1952. Discussion by Fred C. Bond, J. Myers, Norman Weiss, Harlowe Hardinge, Oscar Johnson, L. E. Djingheuzian.) 1069 The Third Theory of Comminution. (Paper by Fred C. Bond, Transactions AIME, 193, 484; Mining Engineering. May 1952. Discussion by Milton C. Shaw and Donald R. Walker; R. J. Russell.)1071 Flotation Rates and Flotation Efficiency.t (Paper by Nathaniel Arbiter, Transactions AIME, 190, 791; Mining Engineering. September 1951. Discussion by Gregoire Gutzeit and Porter Clements.) 1074]

Jan 1, 1952

By G. L. Oldright, Henry de Rycker, S. F. Ravitz

The upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the operation of sintering. A sinter feed with normal gangue constituents, containing more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead concentrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1944

By E. B. Swanson

There is only one way to transport natural gas and that is by pipe lines. In the past few years, these lines have been extended rapidly into areas which previously had been served mainly by solid and liquid fuels. In the subject given me, this extension is referred to as an invasion, which implies a rather forceful entry. Whether or not such an implication may be applied to recent natural-gas developments is unimportant. It is the fact of the extension, not its definition, which is important. For centuries, natural gas has been utilized for various purposes in many parts of the world. It was the foundation of fire worship at Baku. The Chinese used it for the evaporation of brine in salt manufacture. In our country, its history seemingly dates back 110 years to the vicinity of Fredonia, N. Y., where seepage gas was assembled and used for lighting purposes. A few years later, a %inch pipe was laid to a lighthouse on Lake Erie, and the early records of the Lighthouse Service tell of the difficulties surrounding this use. With the discovery of oil in Pennsylvania, there followed further development; the town of Titusville was piped with natural gas and, some few years later, gas was made available for manufacturing plants adjacent to the oil fields. For more than a half century, the industry was concentrated in the

Jan 1, 1932

By Frederick G. Coqueron, Joseph E. Pogue

FOR a number of years, the Department of Petroleum Economics of The Chase National Bank has been conducting a study of the capital employed in the petroleum industry. The technique followed is that of combining and summarizing the available financial and operating data for a group of thirty representative oil companies, doing about two thirds of the domestic business of the entire industry. This paper presents the results of the findings for the year 1943, and supplements the survey, "Sources, Disposition, and Characteristics of the Capital Employed by Thirty Oil Companies During the Nine-Year Period, 1934-1942," presented before the Petroleum Division of the American Institute of Mining and Metallurgical Engineers on Feb. 24, 1944, and also published as a pamphlet by The Chase National Bank.

Jan 1, 1944

Jan 1, 1925

By C. W. MacGregor

THE observation of the flow layers, or Lüders&apos; lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-steel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are in reality traces of wedge-shaped flow layers and are formed by the intersection of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45° to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ner, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45° to the principal stress direc-tions at the point. As examples of the latter may be mentioned the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subjected to internal pressure only, etc. Hence if the flow layers are observed from an experiment, the shear-stress trajectories -the curves indicating the directions of the maximum shearing stresses in the body-may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45° to the principal stress directions, the family of principal stress trajectories, or the curves indicating the directions of the principal stresses, may be thus obtained. Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowan;1 in duralumin and other aluminum alloys, by Dawidenkow,2 Elam,3 Fell, and others; in copper and copper-alloy crystals, by Elam;5 in brass by Elam;5 in brass wires by deForest;6 in higher carbon steels, tungsten steel, and

Jan 1, 1939

By Donald L. Katz, Leo B. Bicher

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944