Search Documents

By James T. Kemp

SOME interesting and, to American eyes, rather unusual processes for refining impure aluminum derived from scraps were found by American and British investigators who went into Germany in 1945 for the Technical Industrial Intelligence Committee Of the Joint Chiefs of Staff. What was found was recorded in a series of reports (see page 14), many of which have been released for general reading. This paper gathers under one title and summarizes the German work in refining light metal scrap. Reference must be made to the original reports for greater detail. Basically, the occasion and stimulus for the German developments in treating light metal scrap were hard necessity. Germany needed the metal for a rapacious war industry. Adequate supplies of new aluminum from reduction works were not assured. Great quantities of airplane and other light metal war scraps were forecast. It was evident that the scrap metal would have to be reabsorbed by the producing industry and would have to be kept of good quality. The normal current production of manufacturing scrap was being and could be consumed as generated. It offered no technical problem. The mixed scraps, especially those arising from crashed and decommissioned airplanes, however, presented problems of another kind. AIRPLANE SCRAP The recovery of usable aluminum alloy from the mixed assemblies that made up the piles of airplane scrap was attacked in different ways by different groups and with differing degrees of success. Three procedures actually were used On a commercial scale, one was in pilot-plant stage and another had come to a halt in the laboratory a year before Germany collapsed. Four of these five processes actually involved "refining"; that is, some measure of purification of the metal after melting. SORTING AND SEPARATION ON A SLOPING HEARTH The simplest procedure for utilizing airplane scrap involved no refining in the strict sense of the word. This was the practice adopted by two representative plants visited by the author, the Leipziger Leichtmetalle Werke, Rackwitz, Saxony, and the Vereinigte Leichtmetalle Werke, Hanover. These firms did essentially the same thing that was done in England but not with equal success, to judge by their shorter experience, the smaller tonnage handled and by the number and quality of alloys produced. The two German firms named rough-sorted scraps by their easily recognizable alloys, essentially by part and shape. They used hand labor to chop and hack and tear apart. The easily separated heavy metal and nonmetallic scraps were discarded as they were found. Steel and the higher-melting-point metal parts riveted to aluminum or built into

Jan 1, 1947

By T. G. Madgwick, A. Beeby Thompson

FoR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippere and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world's supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure important commercial communication with the outside world through the medium of the Black Sea. The first tank steamer was successfully launched on the Caspian in 1879, by Messrs. Nobels, for transporting oil in bulk instead of in barrels. In 1905, an 8-in. pipe line to Batoum was completed; this was capable of transporting to seaboard 8,000,000 bbl. of kerosene per annum.

Jan 1, 1921

DAVE BARTLEY and Edwin F. Gray, miners, late of Shasta County, California, young, healthy, and "dead broke," arrived at Ely, Nevada, one evening in the summer of 1900. Before rustling jobs and going to work, they decided to look around the camp, and in pursuance of this plan they visited a number of claims owned by D. C. McDonald, Justice of the Peace and pioneer of the district. Among the claims he showed them were the Ruth (named after his daughter) and the Kearsarge. Both were regarded as possible gold or silver properties. For no very definite reason the two miners changed their plan and took a lease and option to buy the two claims for $3500. After the transaction was closed and the partners were alone, Gray asked Bartley what he thought of the ground. "If she's good for anything, it's copper" was the reply; and, so far as the records disclose, that was the first time that anyone ever thought of Ely or the Robinson mining district, as it was called, as a possible copper area. There were some slight surface indications of copper, but it is probable that the fact that Bartley had just come from a copper district had something to do with his predilection for a metal that was much despised around Ely. In any event, his hunch was good, and he spoke with the wisdom of an oracle. For thirty years prospectors had sought gold and silver around the camp. Several stamp mills and cyanide plants had been put up and a hundred shafts had been sunk, but fate had been indifferent in its rewards to the optimistic owners. Copper ore would have to be hauled by wagon, 150 miles down Steptoe Valley to the Southern Pacific Railroad, and there was scant hope of finding ore that would bear this cost. W. B. Graham, who ran the general store in Ely, grubstaked Bartley and Gray, furnishing them with food and mining

Jan 1, 1933

By C. C. Griggs

From its inception, a limestone quarry or mine should be under the direction of a capable engineer. Before it becomes a reality, he should outlinc the future results, plan the most economical methods for moving the materials and the most efficient equipment, and pilot the undertaking along the narrow pathway of success, avoiding the pitfalls of uneconomical production and the precipitous walls of scanty profits. Inspection of successful limestone properties shows that all have had difficult engineering problems, the solution of which have required keen engineering ability. In approaching a subject of this nature, it is logical to follow the progress of the limestone operation from its inception to the end, as reflecting the engineering required. There are four major divisions: Investigation, equipment, development, and operation. Investigation On the reliability of the engineer's estimates and the soundness of his judgment depend the success or failure of the enterprise. When one visits a prosperous concern, realizes that the limestone is of a constant chemical composition, sees the mechanical devices installed, and watches the output leave the plant in trains of railroad cars or fleets of vessels, he may overlook the fact that in the remote past this great creation was born in some man's brain and evolved through competent engineering. Many factors must be considered before a promoter could procure the money necessary to launch such an enterprise, for a conservative banker will only recommend a successful producer while the promoter must provide funds on his own and his engineer's judgment. An engineering investigation must be made preliminary to expenditure for actual operation, which, for a limestone deposit, would' naturally embrace such subjects as : ' Readily available. 1. Tonnage available........ Possibly available. Chemical analysis.

Jan 1, 1925

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

My predecessor in the office of President of the Institute started a custom of visiting the various local sections, thus obtaining their points . of view and their ideas as to how the Institute can best serve the interests of its members. Exceedingly valuable- exchange of ideas was thus brought about. I am following this custom as far as the limited amount of free time at my disposal will allow me, and I trust that my successor in office will appreciate the benefit to be derived from following the custom thus initiated and will continue the swing around the circle of the local sections. The activities of the Institute are increased by the prestige gained from large numbers and I trust that every member of this local section will consider himself a member of the committee on increase of membership and will see if he is not able during the coming year to gain at least one new member for the Institute. This is a perfectly possible proposition for, although the membership of the Institute is at present approximately seven thousand, I feel sure there are at least seven thousand more men in the United States who are interested in mining, metallurgy or geology from the metal-mining point of view who would make admirable members or associate members of the Institute. The first consideration of the Institute as a body, and of each member as an individual, is to win the war and defeat the Huns. In order to accomplish this, the Institute, as a body, has cooperated with the other national engineering societies and the great bureaus of the Department of the Interior, the United States Geological Survey and the Bureau of Mines in forming committees to study and advise the Government on pressing problems of vital importance.

Jan 5, 1918

By William Hume-Rothery

I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By William Hume-Rothery

I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By Carle Hayward

SULPHUR has long been one of the banes of the steel manufacturer and often no effort and expense have been spared in order to reduce it to a small per cent. in the finished product. This condition is clue to a general conviction that in many cases where steels have failed in service, sulphur has been the cause. But there has been a growing feeling in recent years that the verdict against sulphur has been unnecessarily severe. In cases of segregation it was present in augmented amounts along with other impurities, but it had not caused the segregation. High sulphur in pig iron is caused by poor furnace conditions and the sulphur is merely one indication of an iron that has not been properly reduced. No amount of subsequent treatment under oxidizing conditions in the open-hearth furnace can remedy the defects, although the per cent. of sulphur may be considerably reduced. In other words, the causes of bad steel can frequently be traced back to bad pig iron, and sulphur is merely one indication that the pig iron is bad. The writer recently visited a steel plant where a mass of evidence had been accumulated which substantiated this fact, and the superintendent was .emphatic in stating that high sulphur was not harmful provided the steel was not otherwise poor due to insufficient reduction in the blast furnace. The presence of a moderate amount of sulphur is desirable from the standpoint of the man who machines the steel. The low-sulphur material drags and the production of a smooth surface is very difficult. A slight increase in sulphur enables the machinist to produce a smooth surface without difficulty. Since, therefore, such large quantities of steel are subjected to machining, it becomes highly important that the sulphur controversy should be settled, and if its presence is proved to be harmless the ban on it should be lifted.

Jan 10, 1916

By F. W. Bloecher

DETERMINATION of the surface area of finely divided minerals is of interest to mineral engineers engaged in flotation, comminution, and de-watering studies. In the industrial minerals field, many materials are classified as to fineness according to their specific surface (surface area per unit weight). A method of surface area determination has been tested and used in the Richards Mineral Engineering Laboratories at M.I.T. It involves low temperature krypton adsorption measurements using the technique described by Beebe.' During the past fifteen years a number of new surface measurement techniques have been developed. Those that are broadly applicable to materials dealt with by mineral engineers include the permeability method in which a gas or liquid is passed through the sample, and the low temperature gas adsorption methods first described by Brunauer, Emmett, and Teller."" Efforts to make surface determinations from size distribution curves have long been attempted"."." but because of the uncertainty of sub-sieve size distribution and inaccuracies in screen analyses, the method is at best only a rough approximation. The most widely used gas adsorption method utilizes nitrogen gas." Nitrogen adsorption, however, is not particularly suited as a tool for most mineral engineers because the method is not applicable for surface determinations on coarse materials, that is, materials coarser than approximately 150 to 200-mesh. Other gases have been used in mineral engineering studies, particularly ethane."' lo The use of ethane gas, however, involves .a technique that is too sensitive for most mineral engineering work. The permeability method of surface area determination has the disadvantage of not being sensitive enough to detect the surface represented by minute cracks, the so-called internal surface of a particle. The low temperature krypton adsorption method described by Beebe1 utilizes apparatus and techniques that are essentially the same as those used in the ethane adsorption method."1° The surface area is calculated by the B.E.T. method."-' The krypton adsorption technique is particularly suited to the needs of the mineral engineer because: (1) The method can be used for making surface area measurements of rather coarse materials (35 to 48-mesh), as well as extremely fine materials, such as clays or colloidal slimes with specific surface that might be as high as 20 to 30 mb er g. (2) The use of krypton gas offers the advantage of low saturation pressures (2-3 mm) at the conveniently obtained liquid nitrogen temperature. Therefore the krypton vacuum system need not be designed to measure or withstand internal gas, pressures above one atmosphere as is the case with the nitrogen gas method. (3) The krypton technique offers the safety feature of employing liquid nitrogen, as contrasted to the ethane technique in which liquid oxygen is required. Furthermore, ethane vapor pressure at liquid oxygen temperatures is low (about 10 microns), and a high sensitivity McLeod gage is required for pressure readings. (4) The measurement technique with krypton gas is much simpler and faster, and the apparatus is less elaborate than that required with either nitrogen or ethane gases. Apparatus A krypton surface measurement apparatus like that used at M.I.T. is shown in Fig. 1. It is constructed of pyrex glass. A vacuum is maintained by two mercury diffusion pumps in series backed by a mechanical vacuum pump."' The vacuum thermocouple gage is used for checking the vacuum within the system. This type of gage is quite sensitive down to a pressure of 1 micron of mercury," but may be used to indicate pressures much lower than that

Jan 1, 1952

The Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recommendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush,. .. New Haven, Conn. *Prof. Oscar D. Allen,. .. New Haven, Conn. *C. Constable,.....New York City. *Leven S Goodrich,.... Oxmoor, Jefferson Co., Ala. *Charles J. Nourse,.... Columbia, Lancaster Co., Pa. *J. W. Mickley,.....Hockendauqua, Pa. *Hugh Alex. Crawford,. ..St. Louis, No. *General Ario Pardee,. .. Hazleton, Luzerne Co., Pa. N. W. Lord,.....New Pork City. J. Holme Maghee,.... New York City. *George E. B. Jackson,. .. Portland, Me. *Charles W. Watkis,.... Salt Lake City, Utah. *Charles E. Hall,....Philadelphia. *Charles J. Duval,.... San Francisco, Cal. Joseph Gorlinski,.... Salt Lake City, Utah. * Alfred Wartenweiler,. .. Salt Lake City, Utah. Wilmot J. Bowen,.... Salt Lake City, Utah. *Joseph Stokes,..... Trenton, N. J. Jason P. Brown,.... Boston, Mass. *William Davis Hartshorne,. . Bethlehem, Hunterdon Co., N. J. *Henry Williams,.... Spanish Bar, Clear Creek Co., Cot. *Robert Forsyth ,....Chicago, Ill. *S. T. Wellman,.....Cleveland, Ohio. *H. C. Walton,.....Chicago, 111. *Andrew Roy,.....Columbus, Ohio. *James H. Rittenhonse,. .. Providence, Pa.

THE Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recom¬mendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush, - New Haven, Conn. *Prof. Oscar D. Allen, - New Haven, Conn. *C. Constable, - New York City. *Leven S Goodrich, - Oxmoor, Jefferson Co., Ala. *Charles J. Nourse, - Columbia, Lancaster Co., Pa. *J. W. Mickley, - Hockendauqua, Pa. *Hugh Alex. Crawford, - St. Louis, Mo. *General Ario Pardee, - Hazleton, Luzerne Co., Pa. †N. W. Lord, - New York City. †J. Holme Maghee, - New York City. *George E. B. Jackson, - Portland, Me. *Charles W. Watkis, - Salt Lake City, Utah. *Charles E. Hall, - Philadelphia. *Charles J. Duval, - San Francisco, Cal. †tJoseph Gorlinski, - Salt Lake City, Utah. *Alfred Wartenweiler, - Salt Lake City, Utah. †Wilmot J. Bowen, - Salt Lake City, Utah. *Joseph Stokes, - Trenton, N. J. †Jason P. Brown, - Boston, Mass. *William Davis Hartshorne, - Bethlehem, Hunterdon Co., N. J. *Henry Williams, - Spanish Bar, Clear Creek Co., Col.. *Robert Forsyth, - Chicago, Ill. *S. T. Wellman, - Cleveland, Ohio. *H. C. Walton, - Chicago, Ill. *Andrew Roy, - Columbus, Ohio. *James H. Rittenhouse, - Providence, Pa. * Members. † Associates

Jan 1, 1875

By G. E. McElroy

MUCH attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for equal values of the product W D V, where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and m = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Prof. Osborne Reynolds' more than 40 years ago. Later, Lord Rayleigh amplified the theory2 which has been conclusively proved for small pipes by the experiments of Stanton and Pannel3 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,5 has outlined the application of this theory to mine-air flow and recent English experiments' on the resistance of a timbered mine airway have been expressed in this form.

Jan 10, 1926

By Frank Haas

Many articles on the physical properties of fire damp have appeared in the Transactions and elsewhere but practically nothing has been written in regard to its occurrence or fluctuation in quantity in an ordinary mine. After the Monongah explosion in 1907, with the loss of 361 lives, the Consolidation Coal Co. sought a method by which such catastrophes could be prevented. While the cause of this particular explosion was attributed to coal dust, some of those acquainted with the mine thought that fire damp was involved, if it was not the initial cause. So the literature on the subject was studied and mines where similar conditions prevailed in this country and Europe, were visited, with the view of establishing some system by which gas could be more easily detected and controlled. The results of this study were disappointing for no method was found other than the time-honored fire boss with his safety lamp, with some variations in the rules and regulations governing his inspections and reports. Duties of the Fire Boss Pending the development of a better method, it was decided to standardize and perfect the duties of the fire boss and the reports based on his observations. Those who were then in service were closely examined, various lamps were experimented with and the lamps and individuals tested under known conditions. It was found that a fire boss could tell whether gas was present but his estimate of quantity was not even an approximation; therefore, while the services of fire bosses were indispen-sible there was need of additional information by which the quantity of gas could be estimated with some precision in order to determine its variation from time to time. Chemical Process for Determination of Methane After considering all methods known at that time a chemical process was adopted. The principles involved in the process are that in an enclosed receptacle, in the presence of excess air, methane will be completely burned by means of a hot platinum wire to carbon dioxide and

Jan 1, 1927

By Samuel Thomas

The specimen of anthracite coal which I hold in my hand, insignificant as it may appear to the casual observer, speaks volumes to me and to the initiated, as it suggests and represents the entire evolution of the use of anthracite coal in the manufacture of pig-iron, the growth and development of which it is my purpose to review here to-day. During our recent visit to the Mountain Copper Co.'s works at Keswiek, I picked up this piece of coal from a pile of anthracite lying in the yard, asked Mr. Edwards, the manager, a countryman of mine, where it came from, and, to my surprise and delight, discovered that it had been brought all the way from Wales, and had come out of the identical vein which my father opened near Yniscedwin, about eighty years ago. I had no idea, before this incident, of contributing to the already full and complete programme of the day; but, being requested by our distinguished President and Secretary to do so, I consented to relate here the story which this remarkable find naturally brought back to my mind.

Jan 1, 1900

By C. Willard Hayes

Introduction.—The recent developments in the metallurgy of aluminum and its consequent rapidly growing use in the arts are at present attracting considerable attention to its ores. The success of the Hall electrolytic process, by which the metal is obtained directly from the oxide, has removed bauxite from the position of a rather uninteresting mineral to that of an important ore. Its production on a commercial scale is so recent, particularly in this country, that little attention has yet been paid to its mode of occurrence and origin.. Any investigation, therefore, which throws light upon these points should be of interest to mining engineers- at the present time, especially if the conclusions afford a basis for estimating the probable extent and value of deposits already known and a mane of directing search for others. Two localities in the United States have so far yielded bauxite in commercial quantities. These are in Arkansas and in the Coosa valley of Georgia and Alabama. According to descriptions of the Arkansas deposits by Branner, they bear little resemblance to those in the Southern Appalachians and their geological relations appear to be entirely different. Only the latter deposits are considered in the following paper. These have been briefly described by McCalley† and Spencer.† They were visited by the writer during the past summer and somewhat carefully examined, in connection with the study of the areal geology of the region. Location of the Deposits.—The ore is found irregularly distributed within. a narrow belt of country extending from' Adairsville, Ga.,

Jan 1, 1895

With the exception of the mentions of coal in Illinois in the period 1660-1680, already referred to, the first coal found in the United States was in the James River, Virginia, field. In 1699 a large tract of .land above the present city of Richmond was allotted for a settlement of French Huguenots by the colonial, government, near the present Manakin, about fourteen miles above Richmond. They soon found coal, tradition says it was uncovered by a hunter pulling out a small tree in a. steel) bank near a stream, and Colonel William Byrd, F.R.S., the most prominent man of his day in the colony, wrote to the Colonial Council of Virginia, May 10 and 11, 1701: "The 10th of May, last., I with Coll. Randolph, Capt. Epes, Capt. Webb, &c., went up to the new settlements of ye French Refugees at ye Manaken Town.... We went tip to ye Cole, w'ch is not above a mile and a half from their settlement on the great upper Creeke, w'ch, riseing very high in great Raines hath washed away the Banks that the Coal lyes bare, otherwise it's very deep in the Earth, the land being very high, and near the surface is plenty of Slate.", Some of the Frenchmen were evidently familiar with the use of coal, as on May 22, 1702, "David Menestrier a black smith and one of ye french Refugees Inhabiting at Luciana Petitioning his Excellency that he may have leave to use ye coal mines lately discovered there for his forge his Excellency by and with ye advice of ye Council loth hereby give Leave to ye said David Menestrier to take what coales he shall want. out of ye said Coal mine for ye use of his forge according to ye Prayer of ye said Petition."2 There was some uncertainty about the grant of these lands to the Huguenots which caused the request for leave to use this coal, as a Virginia patent in its usual form allowed the owner to mine all minerals excepting gold and silver, which were subject to royalties for the Crown. After the visit to the coal above mentioned, "Wm. Byrd, understanding the land had not been granted to the French, took out a patent for 344 acres, including the same, (the coal) which patent was dated October 20, 1704".3

Jan 1, 1942

By Frank Van Horn

INTRODUCTION IN June, 1911, the writer spent a few days in studying the economic geology of the vicinity of Park City. During this rather hurried visit a number of specimens of ore were collected, which have since been examined. The results of these investigations show that bournonite (PbCuSbS3) is present in the ores in greater or less quantity. This fact has never before been reported, as far as can be learned. The failure to recognize this mineral is due to its similarity to tetrahedrite, with which it has probably been confused during a long period of years. Jamesonite (Pb2Sb2S5) has been reported from the region in a rather doubtful manner, but the writer has seen it in notable amounts from several mines, and can offer the first analysis of this mineral from the district. Calamine (H2Zn2SiO6) was found at one mine and has never been recognized and reported from the district.

Jan 8, 1914

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone, quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide, The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over-burden was dug by hand labor, dumped to the quarry floor and trans-ported to the dump in quarry cars, Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi-circle around the top of the quarry about 200 ft. from the face and about 50 ft, above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river: As quarrying pro-gressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp,, 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft, above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting hays into which the motors are raised whenever the river reaches flood stage.

Jan 1, 1938

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938