Search Documents

By Michael McDonald

The cold-rolled steel output of cold-rolling mill (CRM) complexes are sometimes constrained by their batch annealing facilities (BAF). This paper examines a cost-effective solution to increasing capacity and quality of the BAF thereby making additional capacity available for CRM output. The solution involves applying a structured system of scheduling and operation to the BAF, using a proven level-2 software model. The system presented has been applied to a wide variety of BAF with all the leading furnace brands. Whether using traditional HN atmosphere or 100% hydrogen, peak performance can be achieved when using a properly configured, on-line, physical thermodynamic model. Given that it is not practical to place a thermocouple in each coil that is being annealed, various methods have historically been used to estimate the time required to properly anneal all the coils in the charge. This paper examines how the latest technology, in wide use throughout the USA, uses a physical thermodynamic model to shorten average cycle times, thereby increasing productivity and reducing energy consumption. The paper also examines the benefit of building thermodynamically balanced charges to further optimize the BAF operation and improve quality consistency by decreasing mechanical property variations.

Jul 30, 2018

By Ulrich Sommers

The Intelligent Furnace (I-Furnace) by SMS group is a smart furnace process and production optimization model. The combination of various tools leads to an optimized heat treatment and production process. It combines a mathematical/physical model to control the furnace with EMG’s IMPOC system for online strength measurement and a newly developed annealing microstructure model to predict material properties. This paper reports about the revamping of an existing galvanizing line, where a mathematical/physical control model has been implemented in combination with an online quality measurement system. This way, the process improvement of continuous galvanizing lines and the quality management of a range of steels including AHSS will be demonstrated. Furthermore, it gives information about the development of the annealing microstructure model to predict material characteristics. Eventually, the I-Furnace will be presented according to the current development and reference status.

Oct 30, 2017

By Bart de Graaff, Victor van Straaten, Edo Engel

The hot blast system is key ancillary plant equipment with respect to safe and stable operations during a long blast furnace campaign. Hot blast stove designs have been optimized to such an extent that in some cases, their lifetimes have surpassed the campaign lengths of the associated blast furnaces by a substantial margin, with the exception of the burner and a few critical areas. This article presents recent developments with respect to designing, building new and operating existing hot blast systems for a long lifetime and at optimized performance. These developments include fundamental improvements such as dome combustion designs as well as increasingly comprehensive packages for inspection, assessment and maintenance techniques. Examples of such techniques are burner replacement with the hot blast system at operating temperature, improved double shell approaches and TOFD measurement applications.

Oct 1, 2019

By Ruediger Holz, Tommaso Settimo, Luciano Vignolo

Optimized CAPEX, OPEX, new products, yield and product quality in new process equipment as well as by upgrading of existing facilities are the key factors for success and profitable operation. For this, innovation in processes and design is crucial. Danieli can support their clients by offering innovative and well-thought-out process equipment and upgrade solutions. In 2018, Danieli has put into operation a complete cold processing complex in Turkey, which includes a new continuous pickling tandem mill featuring latest generation of market oriented technologies. In this line, dedicated to run a broad range of size and grades (IF to AHSS as DP1000), the highly efficient Turboflow® pickling process was selected. This technology already proved its efficiency and ability in former applications handling ultra-thin gauges at speeds even exceeding 400 m/min in the pickling tanks. The 5-stand 6-high OSRT tandem mill features important developments, like actuators to improve significantly strip flatness and a special air knife arrangement on the tandem mill exit side to generate perfect strip surface cleanliness. In galvanizing lines, the zinc pot is the most effective area to reduce costs in operation and consumables and increase the product quality. Danieli has spent significant efforts in developing most advanced technology for the wiping process. A fully integrated system solution has been designed to perform a wiping process with high quality, economy, accuracy and productivity. Center part is the newly developed X-Jet / Compact X-Jet air knife, added by new generation electromagnetic stabilizer as well as robotic systems to reduce human intervention and health risks in this area. This technological package is ideal also for upgrade of existing lines, typically generating a return of investment less than 1 year. On top, Danieli has developed advanced automation systems including L2 and L1 controls to achieve outstanding product performances.

Oct 1, 2019

By Alexander Fleischanderl

Steel market has become somehow unpredictable and requires quick adjustment in production conditions to survive in the harsh market environment. Steel production is not anymore driven by output records, but by efficient cost reduction measures to remain competitive under strongly varying production conditions. Energy efficient production and flexible raw material scenarios have become decisive factors to succeed and survive in our industry. Such scenarios have to be carefully investigated to be well prepared to adopt production steps continuously. The paper analyses various process opportunities to optimize energy and raw material consumption in the production route. Off-gas treatment systems have still a huge untapped potential to recover energy from the hot waste gases. This is valid for the EAF mini mills as well as for the integrated route. Various examples for waste heat recovery systems including resulting benefits are discussed for the EAF, agglomeration, blast furnace, direct reduction and BOF. New innovative bag-filter systems feature extremely low emission levels at lowest pressure loss and sound emission conditions. Also improved control and automation solutions support the operators to minimize the operation and maintenance costs of their off-gas system. Steelmaking by-products shall not be considered as residues, but as a valuable and cheap raw material source. The paper presents some show cases how to valorize slags as well as utilizing coke and iron oxide fines to increase productivity and minimize raw material cost. A new process for highly flexible converter steelmaking allowing for extraordinary high HBI and scrap rates above 50% and improved yield is discussed and evaluated

Oct 30, 2017

By Sébastien Gérardin

Developed for more than 30 years, continuously improved, cored wire is nowadays a reliable solution for the improvement of sustainability, safety, health and doing quality and cost saving. Cored wire allows the addition of ferroalloys and treatment of liquid steel, especially concerning the calcium treatment. Amongst all the processes in secondary metallurgy, calcium treatment is certainly the most critical one before casting. Besides the traditional CaSi and CaFe wires, new types of wire have been designed for becoming the new reference in calcium treatment. PapCal (calcium insulated wire) and HDx (high density calcium wire) are a very versatile range of products. Indeed, according to the steelmaking process parameters (steel grade, treatment temperature, ladle size, calcium content targeted in tundish and even injection conditions), their technical specifications may be adapted in order to optimize the calcium treatment as high as possible.

Aug 16, 2017

By Bimal Nathwani

This paper presents an overview of bearings failures with focus on steel mill applications such as continuous casting, rolling mills, multi-roll cluster mills and wire and rod mills. This paper will also provide countermeasures for prevention of these modes of failures.

Jul 30, 2018

By Norbert Asamer, Stefan Purrer

Depending on the product or the material grade, conventional deburring machines, such as e.g. with rotating hammers, are in many cases not capable to reliably or completely remove burrs from the edges of a continuously cast product. Burr, however, is generated at the front and/or tail ends of a slab, bloom or billet as a result from torch cutting. Likewise, traversal grinding of the slab’s rolling surfaces can also cause burr at the long side edges of the slab whereby such burr can even be more difficult to remove. Based on their experience and know-how with abrasive machining processes (abrasive cutting, high-pressure grinding) over a period of more than 50 years up to now, BRAUN has developed a highly flexible deburring grinding machine for applications which are too difficult for conventional deburring techniques. BRAUN’s deburring grinding machines were successfully introduced to the steel industry and have proven their worth under normal production conditions already. The subject paper describes the key features and advantages of BRAUN’s machine design and the operational results from the first already completed projects.

Oct 1, 2019

By Ron Webber

With the difficult economic challenges currently facing the steel industry, it is essential to perform a complete analysis when determining which rolls to purchase. A properly designed “Total Cost of Ownership” model can result in significant savings. This paper will review the costs associated with rolls in both Hot Strip and Cold Strip Mills. The multitude of factors that must be considered in performing a complete analysis for the roll purchasing process will be discussed. Models for both Hot Strip and Cold Mills will be presented. Examples where traditional analysis can lead to expensive, incorrect decisions will be presented.

Oct 30, 2017

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017

By Gerhard Richter, Norbert Asamer, Gerwald Decker

At various stages during their manufacturing processes - from casting to finishing before delivery - semi-finished steel and special alloy products must be cut and surface-treated as well. The requirements for the individual conditioning steps, however, can be quite different. For example, the work piece can be hot, warm or cold. At any rate, the product must always be perfectly prepared for the next manufacturing step - reliably, in the shortest-possible time and at the lowest-possible cost. For cutting and grinding, BRAUN has developed innovative technologies and highly flexible, tailor-made solutions which meet these requirements in the most optimal way. In particular, BRAUN’s cutting and grinding technologies can also be used for large-scale products.

Oct 1, 2019

By Marco Castenetto

Some of the most significant Danieli innovations in the field of long products are the: i) The EWR® system, through automatic continuous head-to-tail flash welding of billets at reheating furnace exit side, enables uninterrupted production of the mill for endless rolling of straight bars, wire rod and bar in coils. The process is particularly beneficial to wire rod and bar-in-coil mills as it enables production of “customized-size coils” (any coil weight according to specific Customer request) and with extra-high final coil weight, even starting from low-weight billets; ii) The Spooler process is based on twistfree winding of hot-rolled rebars into highly-compact/ultra-heavy coils featuring a unique cobble-free un-coiling capability. This enables high-speed feeding of the downstream cold-processing lines with hot-rolled spooled coils coming directly from the rolling mill without the need of any traditional off-line operation (such as de-coiling, stretching & re-winding). The system results highly beneficial both to bar-in-coil producers and to the downstream lines operators. The latest step forward is the combined application of these two systems that has made it possible for endless rolling of spooled bar in coils, enabling to cumulate the benefits of the two processes, particularly as far as transformation costs are concerned.

Aug 16, 2017

By Edo Engel

Hot Blast Stove Technology has been developed to such an extent that low cost hot metal production for over 30 years without major repairs has become achievable, making the decision for a campaign length between 5 to over 30 years a design choice for the plant owner/operator. Some of the earlier examples of designs capable of such long campaign lengths are currently close to the 50th year of their running campaign. These examples are found especially in Europe and North America. Along the duration of these campaigns, repairs to subsystems such as burners, hot blast outlets etc. may be required. Depending on a plant’s up and down stream production capacities, the repairs may have to take place in the shortest possible time frame to minimize production loss. This article discusses an approach for intermediate repairs, executed while keeping the majority of the system at operating temperature.

Oct 30, 2017

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By Bruce V. Kiefer

A modernization project was undertaken by Kroman Celik Sanayii A.S. in order to improve their product quality, consistency and shape of the coil package, reduce maintenance and delays in rod mill, thereby increasing utilization and productivity. The project involved installation of a new Morgan Intelligent Pinch Roll and High Speed Laying Head, modifications to the existing controlled cooling conveyor, plus replacing the coil reforming station. The new pinch roll and laying head were to provide better control of the ring formation and consistency of the coil on the conveyor, while reducing delays on the conveyor. Changes to the controlled cooling conveyor included installation of new nozzle decks and Optimesh air distribution system along with re-arrangement of existing fans in order to improve both cooling rates and uniformity of cooling. This paper explains details and features of the newly-installed equipment technology. Resulting product and process improvements are presented, including increased tensile strength and uniformity, reduction in delays on the conveyor and reform tub, plus improvements in coil quality.

Oct 30, 2017

By Wan-sub Kim, Joon-Tae Lee, Seongkyu See, Yong-Kyu Park

Softening heat treatment of CHQ alloy steel (Cr-Mo Steel) is a bottleneck process that requires 90% or more of the entire manufacturing process. In order to reduce the property deviation between edge and center and remove the low-temperature structure problems, CHQ products is heat treated by customers. This technology comes from the idea to solve the problem by applying the concept of “In-line isothermal transformation through initial quenching + heat source addition. Consider the stability of field operations, durability from high ambient temperature and fall of scale, Instantaneous heating and cooling control was required for the conversion of slow cooling and rapid cooling products. An electric heating system was applied to the underside of Stelmor air-cooling nozzle. Using the Scan Pyrometer, the feedback control was performed and fine temperature control was performed through the thermocouple by zone. Through the this technology, it is possible to develop and expand products that can be shortened or omitted by the heat treatment process of customers.

Oct 1, 2019

By Detlef Ehlert

Flexibility in terms of producing high sophisticated products with an exceptional wide range of properties and dimensions requires physical based process models for the generation of optimal set points. Therefore SMS applies since many years an integrated PSC® (pass schedule model), PCFC® (profile, contour and flatness model) and CSC (cooling section control) for the use in hot strip mills, CSP® plants and plate mills offering best possible product tolerances. Focus during the development of the model was made on the best possible physical description of the rolling process to minimize the need of complex adaptation algorithms. As an addition SMS has also developed a microstructure model to ensure the quality control with respect to mechanical properties and to save up the needs of taking samples. Beside of this the modular design of the Microstructure and Material Property Model (MPM) offers additional benefits to improve the accuracy of the other models, e. g. the recrystallization model in the finishing mill. Using the results of that model strain hardening or softening effects during rolling can be predicted and an optimum pass schedule can be calculated to avoid rolling stability problems related to phase transformation.

Aug 16, 2017

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017