Search Documents

DURING September, the Coal Commission pre- pared for issue a series of 18 reports on varied aspects of- the bituminous coal industry; the final report, dated Sept. 22, sums up the facts and offers recommendations addressed to Congress, to the industry, and to the public. The few following paragraphs are selected: Bituminous coal is the real foundation of that great industrial and transportation structure which enables more than a hundred million people to live in America and be so well supplied with things necessary for their health, comfort; and convenience; it also furnishes domestic fuel for two-thirds of the homes of the land. The distribution of the output of the bituminous mines tells the story: 28 per cent. goes to the railroads, 25 per cent. to the boiler houses of factories and mills of all kinds, 15 per cent. to the coke ovens and gas plants, 10 per cent, to the homes, 7 per cent. to steel plants and the same percentage to power plants and street railways, 4 per cent. is exported, 2 per cent is used for power at the coal mines, and the remaining 2 per cent. goes to the seaboard for steamship fuel. Bituminous coal enters into interstate commerce on a scale approached by no other commodity; less than a fourth of the coal mined in the United States fails to enter interstate com-merce. All but one of the 45 coal producing districts in the United States ship coal outside the State in which it is mined. Three hundred miles of cars loaded with coal is the daily output of the bituminous mines of the United States. The public-welfare element in coal is seen in the dependence of public health and safety on an unfailing supply of fuel, in the close connection between the prosperity of most industries and the uninterrupted operation of the coal mines, and in the obvious fact that without coal the great network of railroads which binds together this great country would be idle. The railroads and the public utilities, themselves so clearly obligated to render what-ever public service is demanded of them that the constitutionality of their public regulation is unquestioned, are of all industries most dependent upon coal. Thus, coal makes up over 35 per cent. of the operating cost at the gas plant and over 25 per cent. at the electric power station, and in the operating expenses of. a railroad the cost of coal is the largest single item, next to labor. The practical logic that half a century ago clothed with a public interest the steam locomotive and in later years the electric-power station must recognize a large element of public service in the coal mine that furnishes the necessary energy to both locomotive and power-plant.

Jan 10, 1923

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

Effect of Iron on ash fusion temperature and waterwall deposits FeS, H2S on tube material corrosion and erosion [ ]

Jan 1, 2005

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By R. S. Simkus, J. R. Egan

"Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant test work conducted in 1990-91 indicated that concentrate grades would be substantially improved by reducing the particle size (P,0) of the lead from 38 to 15 µm and the zinc from 45 to 24 µm.Circuit revisions involved installation of major new equipment including: two GUO kilowatt Vertimills for regrinding, a 4 metre diameter column flotation cell and a 4 metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were reassigned.IntroductionThe Sullivan ore body is a massive sulphide deposit consisting of fine grained mixtures of sulphides, sometimes inter-banded with country rock and varying widely in their content of lead, zinc, iron and silicates. Principal economic minerals are marmatite and galena. Iron is mainly present as pyrrhotite (85%), and to a lesser extent as pyrite (15%) .The orebody has been actively mined since 1923, with 1992 ore reserves estimated at 15,800,000 tonnes with an average grade of 4. 7% lead and 7. 9% zinc. Current plans call for treatment of 1,600,000 tonnes/year, (7,000 tonnes per operating day), with flotation feed grades of 5.9% lead, 10.1% zinc, and 22.0% iron."

Jan 1, 1994

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By R Peden

Recent, detailed mapping, (Allibone, 1986; Peden, in prep.) of north west Stewart Island, has shown that the Rakeahua Granite (Watters et al, 1968), is comprised of a wide range of granitoid bodies ranging from diorite to leucogranite. As a result of the wide variation in granitoids Allibone (1986), suggests renaming of the Rakeahua Granite to the Rakeahua Granitoid Complex. Names were also proposed for the individual granitoid bodies mapped.

Jan 1, 1987

By F. G. Heivilin

We are no longer short of viable Rare Earth deposits. As little as 2 years ago China mined and produced 97% ofthe world?s rare earths. Only a few deposits were in an advanced stage of exploration and development. Now Technical Metals Research (TMR) Gareth Hatch *5 reports that 347 deposits are being developed by 265 companies down from 440 on July 6th. Their Index of Advanced projects lists 45 projects in 14 countries. They will sustain the world for centuries to come and many good deposits are yet to be found. The problem is mining 14 elements in balance. Each of the deposits listing production in the chart has a unique set of minerals which they think will give them a cost advantage. Which of these will make it to production is a question. Most of the Advanced won?t be mined soon, but which ones? China is still in the driver?s seat in Light Rare Earth production (LREO) with one deposit with 35 million ton Baiyunebo deposit in Inner Mongolia which is part of a working iron ore deposit. The number of HREE deposits have been reduced and they attempting to eliminate unpermitted mines. This report will tell you what a Rare Earth is, how rare they are, why they are important, and where they are being developed which includes Australia, the United States, Africa, Greenland, Brazil and Canada.

Feb 27, 2013

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane&apos;s table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008

Removal of Dilute Toxic Anions in Wastewater Using Aluminum Hydroxides Co-Precipitation Method

Sep 13, 2010

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003

By Nicholas Chlumecky

One of the oldest mine supports in use today is timber cribbing. In many mining operations material, installation and maintenance costs for timber cribbings are substantial. Their performance characteristics also add to mining costs. During the 1970&apos;6, the U.S. Bureau of Mines recognized many of the deficiencies of timber cribbing and very successfully initiated the development of steel-fiber- reinforced (SFR) concrete blocks. Since the early 1980&apos;s this SFR concrete cribbing has been manufactured as a high quality product which has found increasing acceptance by mine operators. The rapid acceptance of the SFR concrete block cribbing has proven that its use is eliminating many of the deficiencies of timber cribbing while providing superior load carrying capability. The use of SPR concrete blocks to build the cribbing is based on the same principle as wood. That is, stacking longitudinal, rectangular blocks in layers in a crisscross manner. The blocks are positioned at right angles to the blocks of the layer below. With this situation, the possibility of misalignment exists when the concrete blocks at the base are not placed exactly parallel or when the blocks of the base are subject to unequal settlement. Such misalignments creates localized, high stress areas which reduces the load capacity of the cribbing made from SFR concrete blocks. Recognizing the problem of misalignment, the Underground Supports Division of Commercial Shearing, Inc., conceived a circular, one-piece, steel-fiber-reinforced concrete cribbing which is being marketed under the name - Donut Cribbing. This concept eliminates the possibility of misalignment and provides 100% bearing between layers of stacked cribbing as well as other advantages. The purpose of this paper is to discuss the performance characteristics, installation speed and economical factors of each of the three cribbing types -- timber cribbing, SFR concrete block cribbing and SFR concrete Donut Cribbing.

Jan 1, 1986

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By Christian Besson

This article describes the implementation of a new jointing process for use between diaphragm wall panels. This process was initially introduced on the SOCATOP work site in uburban Paris (which involved the closing of the western section of the A86 bypass road), on a tunnel ventilation shaft. This brand new system upgrades the potential offered by other types of joints available and enables both ensuring the continuity of panels for structures over 40 m in depth under the strictest safety conditions and constructing shafts with diameters of less than 15 m. A patent for this process has recently been filed.

Jan 1, 2002

By Joseph Daly

This is the detailed evaluation of the establishment and implementation of an ‘oil recycle plant’ located on site at Boggabri Mine NSW, (Australia); its production, its use and its value. Also discussed in detail is the quality of the raw material produced, and the process and initial application of this raw material generated as well as the analysis of such, as a component within bulk explosive as applied to the mining industry as compiled during analysis. Laboratory analysis prior to field testing is also discussed including independent external laboratory analysis as well as the environmental benefits and a business case for recycled oil in blasting. This paper includes technical details of the product including densities, velocity of detonation and other associated key performance indicators. The intention is to off-set the amount of Distillate (Diesel) utilised as a component of bulk explosives, with a raw recycled oil and thus reducing both the environmental carbon footprint as well as production costs with regard to introduced petrochemical production and utilisation; an oil that is an existing recourse of controlled waste not only difficult but expensive to otherwise dispose of, whilst keeping the entire process ‘on-site’. Though recycled oil in blasting is not an entirely original idea, the key feature of this paper is the ability to complete the entire process on-site.

Jan 1, 2014