Search Documents

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Gustavo Armijo

Slippery and unstable working platforms spoiled not only by natural weather conditions but also by the effects of the construction process (drilling mud, grout slurry) are among the main sources of hazards. Due to this fact a set of recommendations for execution and maintenance of working platforms are presented in this paper, which is based on a study on this subject that is being carried out by AETESS, the Spanish Federation of Geotechnical Contractors. The main objective of this paper is to establish the basis for the right execution and maintenance of working platforms for geotechnical jobs with the idea of increasing safety and productivity. All the aspects involved in working platform safety are analyzed: ground and equipment characteristics, geometric conditions and working platform maintenance. From this analysis a set of general requirements is proposed together with the necessary specific controls before and after the equipment arrival to the job site. In order to facilitate this analysis some flow charts and tables and specific appendixes for each geotechnical technique are included.

Jan 1, 2006

By Unknown

Threats to Industry Theft Potential

Jan 1, 2006

By M Rafty, A Markham, S Atkinson, M Heyting

Over recent years there has been a significant increase in the number of miners in the Pilbara region of Western Australia targeting channel iron deposits (CID) located in valleys, intersected by ephemeral creeks and below the groundwater table. The falling iron ore price has triggered a drive to reduce cost and maximise yield. Creek diversions provide an opportunity to maximise the utilisation of orebodies and extend the life-of-mine.Creek diversions that are required during mining operations to access ore and provide flood protection have historically been constructed as uniform engineered channels designed primarily for flow conveyance while minimising earthworks costs; however, the design of diversions becomes more complex when they are required to function in a similar way to the existing creek system during operations and remain stable during more extreme events than would typically occur following mine closure, in accordance with current regulatory guidance. The design specifications for closure are often more rigorous than the operational phase, and could incur significant additional cost to implement retrospectively if not planned and designed upfront.The complexity of diversion design depends on site specific factors such as: the size of the creek to be diverted; hydrology; corridor restrictions; geomorphology; hydrogeology; geology; environmental and heritage values; potential impacts and the risk to operations and environment. The complex interactions of these factors must be well understood and hydraulic modelling undertaken to characterise the existing creek system, demonstrate the diversions, provide adequate flood protection during operations, and can function in a similar way to the existing system following mine closure. This paper presents key design considerations for Pilbara creek diversions, operational and closure requirements, mine planning considerations, risks, cost saving opportunities, and the benefits of an integrated approach to design.CITATION:S Atkinson, A Markham, M Rafty and M Heyting, 2017. ‘Back to the future’ – resilience in historical context and implications for the future, in Proceedings Iron Ore 2017, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Heikki Laurila, Sirkka-Liisa Jämsä-Jounela, Jarkko Karesvuori

"Artificial Intelligence includes excellent tools for the control and supervision of industrial processes. Several thousand industrial applications have been reported worldwide. Recently, the designers of the A1 systems have begun to hybridize the intelligent techniques, expert systems, fuzzy logic and neural networks, to enhance the capability of the A1 systems. Expert systems have proved to be ideal candidates especially for the control of mineral processes.As successful case projects, an expert system based on on-line classification of the feed type using neural data analysis is described in this paper. The essential feature of this expert system is the classification of different feed types and their distinct control strategies at the plant. In addition to the classification, the expert system has a database containing information about how to handle the determined feed type. This self-leaming database scans historical process data to suggest the best treatment for the ore type under processing. The system has been tested in the Outokumpu Finnmines Oy, Hitura mine. Other projects have been reported to be in progress.INTRODUCTIONIn the past ten years considerable researches have been done in the application of artificial intelligent methods in process industry. The technologies of fuzzy logic, neural networks and expert systems have received several thousand applications worldwide: monitoring and analysis of process operations, fault diagnosis, supervisory control, feedback control and scheduling and planning of operations. Recently, the designers of these systems have begun to hybridize these intelligent techniques to enhance the current capability of expert system. Complex signal processing, neural networks, fuzzy logic and rule-based systems are also implemented to develop new so-called smart or intelligent sensors, actuators or components. Field buses are playing a more and more important role in automation systems and in imbedded systems. The development of field buses has allowed the distribution of smart components over networks."

Jan 1, 2000

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By R Dwyer, S Rea, W J. Bruckard, N McSweeney, R Holmes

"The innate ability of microorganisms to adapt to changing or inhospitable environments has often been exploited for industrial purposes and forms the basis of many current biotechnological processes. The ability of bacteria to adapt and adhere to specific mineral surfaces ensures that the energetic or nutritional requirements of the cell are met and often serves as a survival mechanism under unfavourable?growth conditions or conditions of stress. In this process, cells may rearrange or modify the macromolecules expressed on the cell surface itself or produce extracellular molecules, modifying mineral surfaces to render them more suitable for growth. The modifications that these molecules produce on mineral surfaces may result in changes to the surface charge and hydrophobicity of a mineral. As a result, these biomolecules may have some potential application as flotation collectors or modifiers.In this work, the effect of long-term exposure of Paenibacillus taiwanensis to goethite and common gangue minerals associated with Australian iron ores on the differential expression of membrane and extracellular proteins was determined. Both groups of proteins play a role in cell adherence to mineral particles. Cells were adapted to grow in the presence of each mineral over time. The proteins expressed on the cell membrane and the extracellular proteins excreted by the cell were isolated and analysed by two-dimensional polyacrylamide gel electrophoresis (2D gel PAGE). The outcomes of these studies are presented here and potential application of these products for flotation discussed.CITATION:Dwyer, R, Rea, S, McSweeney, N, Bruckard, W J and Holmes, R, 2013. Microbes and their metabolites - potential iron ore flotation reagents, in Proceedings Iron Ore 2013, pp 369-372 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By A B. Christie, R L. Brathwaite, A Swain

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension.   It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

By Martin Stoklossa

Surface mining operations typically require run-of-mine material to be sized for further processing. In-pit crushing facilities serve this need, as stationary, semi-mobile or fully mobile units. Although in particular fully mobile crushing facilities have been in use for over half of a century, other surface mining techniques have typically been implemented. However, with increasing operating costs in truck and shovel operations, and other economic considerations, mobile crushing plants are increasingly a viable option. The operational and economical parameters in relation to the optimal surface mining equipment selection will be reviewed. The role of the mobile crushing technology within the continuous vs. noncontinuous surface mining operation and basis for mine planning are also discussed. Current applications and respective case studies will be reviewed. Key performance indicators will be presented. These performance parameters can be viewed as a tool to aid in the equipment selection process. The future direction for further research and development in mobile crushing facilities will also be presented.

May 1, 2008

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Javaid M. Alvi

This paper is an attempt to outline the emergence of Augered Cast-ln-Place piles as one of the more economical types of foundation for supporting high-rise buildings and heavily loaded structures recently constructed in the flood plains in and around the Greater Pittsburgh area. To understand the process of selecting foundation types, it is important to understand the general geology of the area and past construction activities that have taken place in the flood plains, especially along the riverbanks, during the last century. The first part of this paper presents a brief description of the general geology of the area; the second part of the paper concentrates on the historical evolution of the use of deep foundations and selected case histories; and the last part presents the results of load tests on large diameter Augered Tremie Concrete (ATC) Piles placed in sandy alluvium which suggests a much larger load-carrying capacity of these piles and also provides an insight into their future application. 2.0 GENERAL GEOLOGY 2.1 Soil Overburden Most of the high rise buildings in the Central Business District as well as along the North Shore and South Side of Pittsburgh are situated in the flood plain at the confluence of the Allegheny River and the Monongahela River where their combined flow forms the Ohio River. The flood plain consists of unconsolidated deposits of Quaternary age that overlie the bedrock of Pennsylvanian age. These deposits are called alluvium or valley fill, and include moderately to poorly sorted clay, silt, sand, gravel and some boulders. Their thickness varies from zero at the edges of the valley to about 80 feet towards the rivers (Figure 1).

Jan 1, 2001

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By Dale S. Preece

"The computer program DMC (Distinct Motion Code) [Taylor and Preece, 1989a] was developed in 1988 and 1989 to predict the motion of rock following a conventional blast. DMC executes very efficiently on a CRAY type computer due to the high degree of vectorization and also due to the use of spherical elements [TayIor and Preece, 1989b]. Bulking mechanisms developed specifically for use with spherical elements include rotation-induced dilatation and aspect ratio > 1.0 [Preece and Taylor, 19901. Rotation-induced dilatation allows the radius of the sphere to expand as a function ofsphere rotation to simulate the interaction of corners and sides of blocky rocks. An aspect ratio > 1.0 is achieved by kinematically tieing spheres together."

Jan 1, 1991

The Porgera gold deposit is an epithermal gold base-metal deposit located in the Enga Province of Papua New Guinea. Gold-silver-sphalerite-galena-pyrite mineralisation is related to stocks and dykes of dioritic composition which have intruded a series of folded marine sediments, mainly shales and siltstones, often with calcareous and carbonaceous horizons, of middle Jurassic to middle Eocene age. The most intensely mineralised zone is at Waruwari Hill, where the mineralisation occurs predominantly as massive mixed sulphide veins, and less frequently as quartz-chlorite veins and as disseminations. Mineralisation occurs in all rock types and several phases of mineralisation have been recognised.

Jan 1, 1980

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By John G. Peacey, Leoncio Sevilla G., Ford. Kevan J. R., Erling Villalobos C.

"Kinross Gold Corporation’s Mantos de Oro (MDO) gold/silver mine in northern Chile currently processes 15,000 tpd of oxide ores through a mill, whole ore cyanide leach plant followed by a Merrill-Crowe refinery. With the expected depletion of these oxide ores in a few years a new sulphide mineral deposit, Ladera-Farellón has been identified to potentially replace existing ore reserves. The deposit contains approximately 0.5g/t Au, 6g/t Ag and 0.5% Cu. The principal sulphide mineral in the deposit is enargite (Cu3AsS4) which hosts the majority of gold and silver and the copper. Direct cyanidation testwork has shown the sulphide mineral is refractory with a low gold recovery of 36% and silver recovery of 45%. Oxidation of the sulphides is required to liberate gold and silver and allow recovery of copper as an important pay-metal. Therefore, at MDO a new metallurgical process route with oxidation as a pretreatment step is required for viable treatment of such new sulphide mineralized material with acceptable recoveries of pay-metals.Analysis of flowsheet options was completed based on bench-scale and pilot scale metallurgical testwork as well as with reference to existing studies and operations. The process options investigated assume concentration of sulphides by flotation, followed by either pressure oxidation, bacteriological oxidation or roasting. Preliminary evaluation of flowsheet options focused on process risk, operability, technology availability and the economics of the project with emphasis on use of the existing metallurgical plant to reduce capital cost. Operating costs for each process option were also included in the relative analysis.The challenges of treatment of MDO sulphides, principally enargite and pyrite for recovery of gold, silver and copper center on fixation of arsenic and sulphur capture with environmentally acceptable disposal of residue tailings. This environmental focus was included in the process option selection and comparative analysis.This paper presents a review of the process options considered and highlights comparative advantages/disadvantages of each process with associated environmental issues. Preliminary conclusions are drawn on roasting as a potentially favorable process option for the treatment of MDO sulphides."

Jan 1, 2009