Search Documents

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

By S. C. Richardson

The electrowinning (EW) circuit involves using DC current in the electro-deposition of metal ions dissolved in an electrolyte solution. This paper reviews a method to generate an electrical model of an EW circuit and the resulting DC current flow and voltage distribution within the circuit. Topics include: calculations of electrolyte conductivity and the equivalent electrical resistance of the electrolyte within the electrolyte pipelines connected to the EW circuit; the breakdown and classification of the EW cell voltage into thermodynamic and ohmic potentials; methods to calculate current flow and voltage distribution throughout the EW circuit; and the development of an interactive visual computer model to simulate an actual EW circuit. Stray current can pose an electrical shock hazard to employees in electrolytic tankhouses. Increased awareness and understanding of the voltage distribution and potential stray current in an EW circuit can help mitigate the risk of tankhouse workers becoming exposed to electrical shock hazards. INTRODUCTION Copper electrowinning tankhouses include rectifiers that deliver large amount of DC current to a series of electrolytic cells consisting of electrolyte solution and electrode pairs. The design also includes metallic conductors in the circuit which include the rectifier’s positive and negative busbar, inter-cell busbar, and the anode and cathode frames. The electrolyte acts as an electrical conductor that transfers current via ions between the anodic and cathodic electrodes within the cell. Electrolyte, as a conductor, is also capable of conducting DC current outside the main EW circuit through the connected electrolyte feed and return pipe systems. DC current that follows a path other than the intended path through the series of electrolytic cells is referred to as “stray current”. Developing an electrical model enhances understanding of voltage distribution and current flow in an EW circuit. This paper discusses the derivation of the various representative components of the model as well as the output from the model. An interactive visual computer simulation incorporates the model output in order to aid in the understanding of voltage distribution and current flow throughout the EW circuit.

Jan 1, 2019

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By J. Moyes

The Intec Process is a generic process for the production of pure base metals and precious metals from sulphides concentrates derived from copper, nickel, zinc and lead ores. The development program for the Intec Process initially focussed on the treatment of copper concentrates, (the ?Intec Copper Process?), and more recently of zinc concentrates, (?the Intec Zinc Process?). Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The knowledge gained during the development of the Intec Copper Process has been applied to the Intec Zinc Process, which utilises the same basic chemistry to produce high purity zinc ingot from metallurgically complex zinc sulphide concentrates containing lead, copper, iron, silver and gold. The demonstrated ability of the Intec Zinc Process to treat low grade mixed zinc/lead/copper concentrates, including those with high iron and manganese levels, holds out the real prospect of overcoming major metallurgical hurdles that have long affected the zinc industry. The Intec Zinc Process consists of the three consecutive circuits of leaching, purification and electrowinning. The leach circuit is of single stage configuration with a series of reactors to which concentrate and lixiviant are fed. Purification consists of cementation and precipitation by pH adjustment. Electrowinning employs an electrolytic cell very similar in design to that of the Intec Copper Process, but differs in that a conventional plate cathode is produced. During electrowinning, the same mixed halide species (BrCl2 -, HalexTM) that is integral to the Intec Copper Process is generated in solution at the anode and exhibits powerful leaching characteristics capable of directly leaching the sulphide concentrate feed. The need to roast the concentrate prior to leaching, as is practised in the conventional Roast/Leach/Electrowin (RLE) process, is thus eliminated whilst a range of by-products (notably lead, copper and precious metals) can be extracted in the simple, single-stage leach. This paper describes the Intec Zinc Process; the technology, predicted economics and its environmental aspects.

May 1, 2002

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By Gloria Fernández

La contaminación por drenaje ácido de mina se considera como la responsabilidad ambiental y económica más grande que actualmente enfrenta la industria minera. En ese sentido, se delimita las áreas afectadas mediante la perforación de pozos de monitoreo a través de un estudio geofísico previo. Por ello, el presente trabajo señala los métodos geofísicos como herramientas que pueden ayudar a delimitar y mapear las zonas afectadas por la contaminación proveniente de drenaje y filtraciones que va desde canchas de relave, pilas de lixiviación a minas abandonadas, etc.

Aug 25, 2002

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By Patrícia Freitas Rodrigues

Um comparativo entre dois métodos para determinação das temperaturas de transformação de fase, tendo como base análises de Calorimetria Diferencial de Varredura (DSC) em amostras de uma liga de NiTi equiatômica submetida a tratamentos térmicos para envelhecimento, foram utilizados neste trabalho. Sendo aplicado o método clássico comumente utilizado para análise desses resultados e o método utilizando da integral do pico de transformação de fase. Com base nas avaliações feitas, o método de integral por apresentar uma relação direta da fração de transformação demonstra-se mais eficaz para determinar o início e o fim da transformação por levar em consideração a forma do pico em função da trajetória de transformação.

Aug 8, 2018

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Under the Town and Country Planning Act 1977 the Ministry of Works and Development has a responsibility for providing information to local and regional planning authorities on public works and matters of national development and importance, for the exercise of their responsibilities under this Act. One such matter which has recently become a source of concern is the development of South Island lignite. In 1979 the Ministry of&apos; Energy produced a position statement outlining a programme of&apos; research leading to the possible extraction of lignite in Southland or Central Otago for conversion into about 50 per cent of New Zealand&apos;s liquid fuel requirements by 1995. Understandably this possibility has caused considerable concern at the local level, expressed particularly by bodies such as Federated Farmers and the local authorities. In the absence of any factual knowledge short of mere conjecture been able to recommend to local authorities is that they limit their planning period to ten years. After this time more information regarding the size, nature, location and certainty of the proposal will permit a more accurate assessment of the implications of the York. While on holiday earlier this year I took the opportunity to visit opencast mining areas in Germany and England to gain an appreciation of the scale of impacts involved and discuss with those concerned the procedures used in planning for such operations. What follows is a brief description of these operations, a comparison with the likely development in this country and the extraction of what may be some relevant principles of&apos; operation for the planning of an environmentally acceptable project. Please note that the views expressed in this paper are mine alone and are not necessarily those of the Ministry of Works and Development.

Jan 1, 1981

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By Raja V. Ramani

The recognition that surface mining need not be viewed as a permanent dedication of the land but rather as a temporary non-renewable use in a series of land uses has caused greater emphasis on the re-use of surface-mined lands. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. have been studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Indian Head Mine, which is located in Mercer County, North Dakota, has been studied. The Indian Head Mine is presently operated by The North American Coal Corporation -Western Division and has been in operation since 1917 under various ownership. The status of current reclamation and postmining land use planning was reviewed. In addition, the relationship between mine planning and public planning in an area impacted by energy development was investigated. Finally, key factors affecting site potential realization for western surface mines have been identified.

Jan 1, 1983