Search Documents

By Klaus Rieker

The main train station of Leipzig in Germany is currently being upgraded from a head station to a partially thru station. In order to achieve this, significant ground improvements are necessary. Soil freezing for example is used to create the excavation box retaining walls. The freezing works will be carried out from two tunnels with an inner diameter of 2.4 m (~ 8ft). The tunnels were constructed by the pipe jacking method. The cutter head of the machine was equipped with discs and scrapers. Driving and excavation was carried out using a bentonite supported face. Due to the small arrival shafts, the machine had to be lifted out in components. The essential limitation of settlements during the drives was achieved even better than expected.

Jan 1, 2008

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By William C. B. Gates

Demolition blasting next to an active railroad can be very challenging because of track safety, blasting vibrations, potential track fouling by blast debris, and short work windows on a live track. Recently, in eastern Washington, one of the major railroad companies has been aggressively constructing a second main track to accommodate the expected increase in rail traffic of natural resource products. To accommodate construction of the second line, the railroad company used blasting demolition techniques to remove an old railroad trestle pier on the Milwaukee Road that was in the footprint of the new track bed. The trestle bridged the present rail line and flanked the track with two massive 550-ton (499 tonne) twin-columned steel reinforced concrete piers. The railroad contracted with a specialized contractor to remove the south pier using blasting demolition techniques. The blasting design presented the following challenges: blasting during live track conditions and short work windows; designing a V-notch blast pattern to ensure the pier fell away from the live track; drilling, loading, and timing of the shot; maintaining blasting vibrations at the track below 4 in./sec (102 mm/sec); maintaining ambient overpressure noise below 133 dB; control of fly rock and debris; and track protection and emergency debris removal plan.

Jan 1, 2016

By Joshua A. Bennett

"Lawsuits where owners allege their property has been damaged by nearby blasting routinely costblasting companies, explosives engineers, and others in the field both time and money. When ownersfeel the vibration of a blast, they immediately begin to look for damage and usually find cracking thatwas, in fact, present prior to the blasting occurring. When those owners begin to talk to their neighbors and legal counsel, blasting entities suddenly have multiple lawsuits being filed as a result of the same blast."

Jan 1, 2016

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

By Oy Leuangthong

Red Dog mine is the world's largest Zn producer. The deposit consists of sulphide ore zones in sedimentary exhalative (sedex) deposits, and is characterized by the presence of multiple metals and multiple ore types. The objective of the case study is to characterize seven different minerals, Zn, Pb, Fe, Ba, sPb, Ag and TOC, within eight different rock types. Geostatistical models were constructed for each variable within the eight rock types, and subsequently assembled to give 40 realizations for six 25ft benches. The stepwise conditional transformation was used to account for the complex multivariate relations. In addition to reproducing the input data, histogram and variogram, the resulting models also respect multivariate relations locally and globally. This paper documents the methodology to construct these models. A thorough validation procedure was implemented. Comparisons with blasthole data show that the conditional simulations and the long-term models agree in expected value. The main advantages of the conditional simulations are (1) the explicit accounting of multivariate relations between the data in model construction, and (2) the ability to quantify variability and uncertainty at any scale. A small exercise comparing the profit from a kriged and a simulated model is also examined. Results show that the simulation approach showed a 3% increase in profit, relative to the conventional estimation approach.

May 1, 2004

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By Lee T. J

The area, A, under a gamma-ray log that passes through a horizontal bed given by: A = gl/k. Here is the equivalent concentration of U3O8 in the body, l the thickness of the body, and k the calibration factor or sensitivityof the logger. The area is independent of the logging speed or logger time constant.This relationship, together with the first moment about the maximum of the log and its value there suflicient to determine the thickness, position of the centre of the bed from the log maximum and the concentration of U3O8.Numerical results obtained from artificial and field data show that the computed results arc as good as those obtained by methods such as the inverse filter technique and the iterative method. The present method yields results that arc easier to feed into an ore reserve data base.

Jan 1, 1981

By F. Ziaie

Line electrical resistivity method using physically infinite distance between current line electrodes is proposed to determine the location of mine workings. In this method at least three line electrodes are used. One of the current electrodes is used as a sinkhole electrode while the other two are used for different activiations of line electrodes when the survey area is between one of the line electrodes and outside the other one. The resistivity profiles perpendicular to the current line electrodes for different activation of electrodes is plotted versus the distance of the midpoint of the measuring potential electrodes. The anomaly due to presence of any locally lateral resistivity variation (e.g. mining cavity) will represent itself as peak or trough depending on resistivity contrast between the source of the anomaly and surrounding medium. Physical simulation of the proposed model was conducted by using a tank model in the laboratory. The results of experiments appear to be consistent with the theoretical model. Experiments for different depths and different spacial locations of the simulated cavities appeared to be successful for locating the depth and size of the cavity.

Jan 1, 1989