Search Documents

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By Leslie F. Sawatsky

Raw water import requirements for oils sands mines depends mainly on factors such as ore processing rate, ore material characteristics, tailings processing technology, tailings storage systems, process water storage operations, the phase of tailings production, and non-recoverable seepage losses from tailings ponds. These factors can be readily quantified to calculate raw water import needs. Nevertheless, mine water balance continues to be misunderstood by some regulators, stakeholders and possibly even mine operators. Confusion over consumptive uses has led to a focus on recycling which is not necessarily applicable to a closed circuit water management system. Some water conservationists focus attention on raw water intake rules instead of the technical decisions that control consumptive uses. Typical oil sands mine water balances for various types of tailings operations, are analyzed to illustrate the effect of controllable and uncontrollable parameters as well as major options that need to be explored for reducing water demand. Uncontrollable parameters including tailings fines content, oil content of ore, connate water, mine depressurization water inflows and surface water hydrology. Controllable parameters include storage operations, advance water supply ahead of mining operations, type of tailings operation, net tailings pond seepage losses, and tailings impoundment operations. Potential reductions of raw water supply rates may be obtained by providing greater on-site storage to attenuate fluctuation in water demand, advance water accumulation prior to mine start up, early commencement of CT operations, thickened tailings disposal and paste technology. Water conservation measures should be focused on reducing on-site process water storage and water content of tailings material.

May 1, 2004

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By Luis Bernal, Pertti Lamberg

"SkimAir®, Outotec’s Flash Flotation unit, is placed in the grinding circuit to float the valuable liberated mineral particles from the circulating load of the grinding process while still relatively coarse. Esperanza copper-gold deposit located near Sierra Gorda, Chile, hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. A series of laboratory and pilot flotation tests were conducted to find out the flotation performance of different ore types both with and without the Flash Flotation. This data was used in modeling and simulating to find the optimal flow sheet for the highest Au and Cu recoveries with required Cu concentrate grade. Simulations with the HSC Chemistry 6.1 software showed that with the SkimAir® and Flash Cleaning it is possible to achieve the required copper grade of 27% Cu with 5% higher recovery for gold and 2% higher recovery for copper compared to the circuit without the Flash Flotation. The pilot tests with simulations were the back up for the installation of four Outotec SkimAir® SK 2400 Flash Cells in the Esperanza circuit for the processing 95.000 tpd of copper-gold ore.INTRODUCTIONEsperanza copper-gold deposit is located near the town of Sierra Gorda, 2nd Administrative Region in Chile. Deposit hosts 535 Mtn ore grading 0.57 % copper, 0.27 g/t gold. The main copper minerals are chalcopyrite and bornite. Gold is carried by native gold and solid solution of copper.Antofagasta Minerals S.A. conducted a series of flotation studies at SGS Minerals Services. The studies included both laboratory and pilot scale work. In the pilot scale study the applicability of the Flash Flotation technology was studied with High-grade Andesite and High-grade Porphyry samples (SGS Mineral Services). The Flash Flotation technology gave significantly higher recovery for gold than the conventional flotation circuit. The recoveries for copper were slightly higher using the conventional flotation."

Jan 1, 2009

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By James McKelvey, Larry Drolet, Jason Swartz

INTRODUCTION When divers discovered that sections of a tunnel housing the pipeline that conveys wastewater from the Charleston Peninsula to the Plum Island Wastewater Treatment Facility had caved in, the Charleston Commissioners of Public Works(CPW) moved quickly to determine a long term solution for the city’s collection system, immediately focusing on the Ashley River sewer tunnel along the western boundary of the peninsula. Working with the Charleston community, as well as federal, state, and local officials, CPW developed a fast track yet long life design that can be used as a model for underground construction of tunnels in urban areas. The paper that follows summarizes key aspects of the Ashley River sewer tunnel project. HISTORICAL CHARLESTON Charleston, South Carolina is a culturally significant and historic city that was originally settled in 1670. There are over 100 buildings on the National Register of Historic Places within the Charleston area. Additionally, the first shots of the American Civil War were fired at Fort Sumter in the Charleston Harbor in 1861. As one can imagine, tourism generates significant business for the area with over 1.5 million people visiting Charleston each year. No project, especially one that requires digging, is done within the old city on the Charleston peninsula without careful planning. Many precautions are necessary to prevent damage or disruption to the historical properties. The Ashley River sewer tunnel project is exclusively in the old city. A lot of work was done during the design phase to minimize the impact to historical properties. Some of this work included: an archeological study (where pre-digs were monitored at all shaft sites by an archeologist); a building/structure assessment study (where structures near a shaft site were completely surveyed and cataloged); and an environmental study.

Jan 1, 2005

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Michael Wieland

The resolving capacity of the thermodynamic work-principal model has been seriously refined over its twelve year history, so a review of the innovations, wrong turns and their rectification is warranted to help future researchers. The work-principal model rests upon the four laws of thermodynamics that drive the universe and relatively few other assumptions: like the removing and imposing of constraints on the quasi-potential to yield trapped minimum key-states that represent the wanted process. The formative research was concerned with the role of ingredient changes, the removal of booster influence and the quench temperature with which to reckon toxic fumes. The transfer of reaction-zone energy as work upon the surrounding rock/water/fixture was not fully rationalized until the notion of reversed-inertial pressure was formulated and determined (for water) with underwater trinitrotoluene (TNT) shots. The rock-water-jelly model incorporated that term into its dynamic pressure formula as a way to represent rock blasts or underwater shots, while the zone of reaction gases remained trapped. The real irreversible thermodynamic process, which yielded the total expansion work, was later complemented with a wholly reversible imaginary process, to form a closed thermodynamic loop, with a remarkable consequence – the determination of the theoretical heave and hence, the undissipated-shock by difference from the total work. With the wholly developed model, it was recently possible to quantify the time retardation of reaction chemistry for non-molecular (mining) explosives, as compared to the rather negligible time-retardation found for the molecular (military) explosives in underwater tests.

Jan 1, 2009

By Branagan D. F

The geology of the area studied is briefly described, together with the prospecting methods used in the search for copper, lead, zinc and uranium ore bodies.Four prospects, Mt. Corella, Yanasinga, Lawlor's and Greenmount, which were diamond-drilled, are described in detail and geochemical results are discussed in relation to the mineralization found. Copper anomalies were found wherever intrusive rocks were mapped, and showed a much closer relation to geology and mineralization than did the predominantly lead and zinc anomalies.Geochemical prospecting aids in the overall mineral search programme because of its speed and economy, as it helps to pinpoint areas worthy of detailed geological examination. Geochemical anomalies are a guide to favourable zones but may not indicate the presence of ore.INTRODUCTIONDuring 1953-55 the National Lead Company of New York carried out a search for minerals in an area south and west of Cloncurry (Fig. 1) in rocks of Precambrian age. After reconnaissance mapping, a number of prospects were chosen for closer examination by detailed geological mapping and geochemical sampling, and from these prospects, five sites were selected for drilling.This paper records the salient features of the exploration programme and discusses the geology and geochemistry of four of the prospects-Mt. Corella, Yanasinga, Lawlor's and Greenmount. Practically all the prospects examined showed high zinc "anomalies" or "dispersion" trains. Greta, Mt. Corella and Lawlor's prospects showed some copper anomalies and, to a lesser extent, lead anomalies. In particular, Greenmount exhibited striking copper anomalies.

Jan 1, 1960

By A. D. S. Gillies

Diesel engine particulate matter pollution is a matter of concern currently in underground mines worldwide. A number of real-time Diesel Particulate Matter (DPM) monitors have been developed in recent years; two of these by the National Institute of Occupational Health and Safety (NIOSH) in the US. One, the D-PDM, is based on an adaption of the successful NIOSH?s Personal Dust Monitor (PDM) unit which is being taken up very successfully for mine respirable dust monitoring. The D-PDM measures all particulate matter within a sub-micron range as classified nominally at 0.8 micrometers by a purpose developed cyclone. The other, the FLIR Airtec, measures the Elemental Carbon (EC) component of DPM by a laser scattering approach. Both instruments have been evaluated underground in robustness and reliability testing in coal mines by the authors. Real time DPM monitors allow greater understanding of the sources and levels of DPM pollution in underground activities. They allow engineering evaluations to determine how conditions can be improved or mining personnel relocated to lower concentration levels. Studies are discussed that examine DPM concentrations from vehicles under varying ventilation conditions. Some of these concern tests undertaken during high activity longwall face moves. They focus on evaluating DPM during the various phases of the face Chock Shield moves. An initiative in some mines has been to limit the number of vehicles in the mining section or panel by the use of a Tag Board or Traffic Controller at the panel travel road entrance to manage exhaust DPM and gases. Diesel tags or tokens are used to control the number of vehicles entering a section or panel and so limit level of pollution. Summation of DPM levels from points monitored throughout a panel demonstrates increasing DPM levels from influence of additional equipment in series within the ventilation circuit. An alternative approach is to invest in underground continuous real-time monitoring of exhaust gases, DPM and section air quantity and integrate this information to determine whether an additional vehicle can enter without exceeding diesel target limit. This optimizes the access of diesel vehicles and replaces the existing manual tag board system. Real-time DPM monitoring allows the industry to pin-point high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. Identification of high DPM zones allows efficient modification of mine ventilation, operator positioning and other work practices to reduce underground miners? exposures.

Jan 1, 2012

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.