Search Documents

By D. Kolymbas

A simple formula is introduced which allows the evaluation of dynamic pile tests. The following case is considered: The pile top is dynamically loaded by an impact. The velocity v of the pile top is recorded over the time. Let v1 and v2 be the first and the second maximum of this curve. Then, the pile bearing capacity (resulting from ideally plastic resistance at the pile wall and at the tip) can be set approximately equal to Z(v1- ½ v2), where Z is the impedance of the pile cross section. Due to the assumption of ideal plastic resistances, radiation damping needs not be taken into account. Material damping may be important in rate sensitive soils (such as clay, even if it is highly overconsolidated). A simple correction procedure for material damping is proposed.

Jan 1, 1989

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Z. Q. Zhou

It is the first worke in design of pile foundation to determine the carring capacity of single pile, and a static loading on site is considered to be the lost derect and reliable way. All values P and settlements S induced can be plotted as a broken-line. Since soil is a kind of elasto-plastic and cohesive material, the increasing of settlements is generally greater than that of loads. Different value Pu nay be given by different tester on his P-S diagram, because of erroys in the test and complicated, characteristics of soil. The analytical method of exponential equation shown in this paper derives a specified solution. After using an exponential curve to regress values of loads P and corresponding settlements S from on-site test, coeficients A and B of exponential equation can be obtained. With this curve an ultimate carrying capacity of single pile can be determined. The resistant forces of pile shaft and pile tip can also be defined by the tangent of the calculated knee point, as it is called (tangent method). At last, an example is given to show how the ultimate carrying capacity of f 500mm bored pile is obtained with this method for a project in Kunming.

Jan 1, 2010

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By Joseph L. Margin

From a stubborn start to record setting performances in little over a year, that is the story of the English Running Tunnel Boring Machines. The program to transfer technical information on these highly advanced machines from builder to user will be discussed as a vital link to this accomplishment. Some interesting features of these machines will be covered as well as a recounting of the various conditions that were encountered during these drives and how they were resolved.

Jan 1, 1991

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By Rodrigo Toro, Mario Delisle, Claudio Zamora

"The mining market is researching innovative methods to train the workforce for mining which is normally extremely difficult to get. Thus, the dynamic simulation-based technologies become an essential pillar to educate and train the inexperienced staff at the pace required by this industry. Even if Operator Training Simulator (OTS) systems are commonly used in most of industries, knowledge transmitted to operators are unfortunately not ""capitalized"" in general. The OTS systems are usually delivered as a single hardware and software platform and very little as a full service long-term.In this article, an integrated solution to increase the efficiency of the operators is proposed. This solution is based on the combination of dynamic simulation, processes knowledge, virtual reality and the knowledge capitalization through the creation of simulation scenarios and e-learning. The Codelco Ministro Hales plant simulation project for a copper concentrator plant is presented as a real life example.IntroductionDynamic and real-time process simulation have proven to be a must in the development of greenfield projects, providing mechanisms to design and test controls design, interlocks, start-up, shut down sequences and operator training, among others (see (McMillan, 2006) for further details). Early adopters of this technology were utility power plants; in the petrochemical industry have become a standard, and in the mining industry the use of dynamic simulations is growing, especially in new projects and training of operations personnel for the adoption of best practices and new technologies, see (Nikkhah & Anderson, 2001) and (Toro, Ortiz, & Yutronic, 2012).This paper outlines a solution that utilizes dynamic simulations as the base of an integrated platform for operational effectiveness, which takes into account the current scenario of new mining projects and operations, where high turn over rates and needs of specialized workforce have given a special value to this kind of technologies."

Jan 1, 2015