Search Documents

Jan 1, 1988

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By J. D. Steenkamp, G. E. Williams

Keywords: Ilmenite, titania slag, pig iron, rutile, zircon Located on the eastern shores of South Africa, 180 km north of Durban, Richards Bay Minerals (RBM) produces approximately 2.0 million metric tonnes of product annually making RBM a leading producer of titania slag, high purity pig iron, rutile and zircon. Heavy minerals are extracted from the nearby dunes by dredging and concentration on a floating gravity separation plant, followed by separation of the ilmenite, rutile and zircon at the mineral separation plant located at the smelter site. The ilmenite is processed through an oxidizing roast followed by magnetic separation and is then partially reduced to an 85 per cent TiO2 slag in one of four six-in-line a.c. electric arc furnaces. The slag is milled and then classified into two product sizes suitable as a raw material for both the sulphate and chloride pigment processes. The high quality iron produced during the reduction process is further processed to produce various grades of low-manganese iron. Around 95 per cent of the products are exported, yielding a world market share of about 25 per cent of titania slag, rutile, high quality pig iron, and zircon.

Jan 1, 2006

To many Australian Mining Engineers, we take it, the singular features of banket deposits are not as familiarly known as they would wish, possibly because in the majority of instances they are not in touch with the South African milling world, and have had little opportunity of studying the development of the banket beds, either from correspondence or literature. The writer hazards this opinion feelingly, because, when in Australia and before he had visited Africa, the utmost knowledge he was able to obtnin was a mass of conflicting theoretic discussion as to the agencies which formed the banket bed, without any practical hints as to their geological horizon, the rocks with which they are associated, the usual appearance and character of the ore, in fine, without that everyday detailed description which the miner requires when seeking information regarding mineral or metal deposit foreign in character to any that he has yet studied, or as yet had any opportunity of studying in his own country.The writer recognised that many more able men than he have from time to time discussed the features and formation of the banket beds of the land, notwithstanding which and feeling that many of his Australian colleagues have found themselves in a similar position regarding accurate detailed information respecting these African banket deposits as he himself was, he hopes that the present paper on the said deposits, as found on the fields under notice, will prove useful to some and of interest to all.

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By Jiwei Duan

The deformation and load transfer behavior of a single soil-cement column are studied with the finite element method. The results show that there is an effective length for a soil-cement column. Beyond this length, the settlement of the column is approximately equal to a constant. The effective pile length is introduced to the concentric cylinder approach (Randolph and Wroth 1978), and an analytical formula for estimating the settlement of a single flexible pile is presented. A second analytical formula for determining the effective pile length of a soil-cement column is obtained and an example shows that the calculated and measured results are in quite good agreement.

Jan 1, 2002

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By Creelman C. A

The removal of a horizontal piIlar between Nos. 9 and 11 levels (1,116 feet from the collar of main shaft) was successfully carried out by blast hole drilling, and, to the best of the authors' knowledge, this mass blast of 40,000 tons of ore (requiring the use of 7,150 Ibs. of explosive and 5,385 feet of primacord) was the first occasion on which a task of this magnitude has been carried out underground in an Australian mine.Blast hole drilling was introduced by this company approximately fifteen months ago at New Cobar Mine in sub-level stoping.This experimental drilling and blasting gave very valuable information as to the correct technique to be adopted when the final plans were being prepared for the removal of the horizontal pillar at New Occidental Mine.The dimensions of this pillar were approximately 15 feet long, and from 40 to 60 feet wide, and 65 feet in depth.The block of ore extended to 35 feet above the level and 30 feet below, the upper section being partially excavated to form the bell-hole floor and grizzly chambers used for drawing off the broken ore in the shrink stope above the No. 10 level.Description of Ore-bodyThe main ore-body is situated almost vertically in a well-defined shear zone at the junction of sandstone and slate, the sandstone forming the eastern and the slate the western wall.The ore-body consists of highly silicified slate (chert) sparsely impregnated with sulphides, containing a small percentage of copper and bismuth.The total length of the ore-body is approximately 450 feet, with a maximum width of 60 feet in the main section, which is about 200 feet long.This is the section shown in longitudinal and cross-section (Fig. 1).The ore-body is divided by a horse of mullock in the northern end into two legs, the eastern and western, which are approximately 250 feet long and averaging 25 feet in width.This ore-body is strong, hard and abrasive with extremely strong walls, an ideal proposition for open stoping and mass blasting.MiningIn all levels above No. 9 the cut and fill method of ore extraction was adopted. On Nos. 10 and 11 levels the shrinkage method was introduced with economical results, and no difficulty had ever been experienced with shabby or bad walls.Shrink stoping had been carried upwards from No. 11 level to within 10 feet of No. 10 level, when mining hazards developed, and instead of...

Jan 1, 1944

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By E. Dzingayi

Keywords: Pyrometallurgy, furnace, Bindura, nickel The smelter at Bindura Nickel Corporation processes concentrates from its own mines and other external sources. Concentrates are dried, smelted, and converted to a desulphurised matte (leach alloy) for further processing at the refinery. The smelter comprises a drying plant, submerged arc electric furnace, electrostatic precipitator, and three Peirce-Smith type converters capable of treating 150 000 tonnes of concentrates per year. Concentrates are dried in a rotary coal-fired kiln, blended with fluxes, and smelted in a six-in-line submerged-arc 15MW electric furnace. Slag is tapped and granulated for disposal, and matte is tapped at regular intervals for blowing in Peirce-Smith converters. The paper details the 37-year history of the smelter, including furnace rebuilds and operating parameters as they have evolved in response to changing feed compositions. Special challenges, particularly relating to the treatment of high talc concentrates, are also described.

Jan 1, 2006

By G. Cordingley, A. Mwanza

Lumwana is an open pit Copper mine located in the Northwestern Province of Zambia approximately 80 km west from the provincial capital of Solwezi, approximately 300 km northwest from the Copperbelt and 700 km northwest from the national capital of Lusaka. The mine has two major Copper deposits: Malundwe and Chimiwungo. Copper mineralization includes Chalcopyrite, Bornite and Chalcocite. In addition to Copper, these deposits also contain the undesirable element Uranium contained in vein hosted and disseminated Uranite. The processing plant was designed using conventional technologies: semi-autogenous grinding (SAG) and ball mill for grinding, and mechanical cells for rougher and cleaner flotation. Soon after commissioning in early 2009, it was recognised that two stages of conventional cleaning were unable to produce plant final Copper concentrates with the desired Uranium grades. Studies have shown that a significant quantity of liberated and fine Uranium particles (up to 80-90%) is recovered with the concentrate by entrainment. Lumwana Operations sought the use of the Jameson Cell technology after observing successful implementation at other sites in rectifying similar issues. In late 2009, Jameson Cell pilot-plant test work was conducted at the site and this quickly led to the installation of a full-scale B5400/18 model into the existing cleaner circuit. Inclusion of the Jameson Cell resulted in the plant being able to effectively produce clean and saleable concentrate with Uranium contents consistently below acceptable levels. Initially designed to be used as a cleaner scalper cell at the head of the existing conventional cell circuit, subsequent operational issues with the existing recleaner cells forced reconfiguration of the cleaner circuit and reintroduced the Jameson Cell for the recleaning duty. This paper reports the Lumwana Operation from the first two years of operation where it struggled to produce a saleable concentrate with Uranium grades below 150 ppm, which is the maximum allowable limit set out in the smelting contracts, to steps taken in the subsequent years to implement a satisfactory solution. The plant can now consistently produce a clean Copper concentrate with Uranium grades well below 130 ppm and the overall improvements implemented at site have seen the overall plant recovery improve by 1.3%.

Jan 1, 2014

By S. Doombos

To convert the railway-bridge across the Oude Maas between Dordrecht and Zwijndrecht into a vertical lifting bridge, a drastic adaptation of the existing piers is necessary. Extra piles have to be placed quite close to the present piers to bear the extra weight of lift-towers and bridge-sections. This article describes the special technology applied to drive steel tubular piles l800 mm. in diameter and 36 m. in length vibration-free into position. At the same time a method of pile-point-reinforcement has been applied to minimize the settlements.

Jan 1, 1989