Search Documents

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By Robert H. Peters

This report presents a literature review conducted by the U.S. Bureau of Mines. The review summarizes what has been learned from the large volume of empirical studies on the effectiveness of eight types of interventions intended to increase organizational effectiveness via in the management of human resources. The interventions concern the following: recruitment, selection, training, objective feedback, goal setting, reward systems, participative management practices and organization development. Although many of these interventions appear to have the potential for improving the safety and efficiency of mining operations, it does not appear that they are being widely used. Examples are given of the successful use of a few of these interventions at mining operations. An analysis of the relationship between coal mine productivity and safety is also presented. This analysis generally supports the view that good safety performance and high productivity are NOT incompatible goals. In fact, safe mines also tend to be more productive and vice versa.

Jan 1, 1992

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By K. Y. Vasioutchkov, Y. F. Vasyuchkov, B. M. Vorobjev

In general a term "unconventional mining or "non-traditional mining technology" getting more and move familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in [Figure 1:] One of the greatest potential for coal utilisation during the beginning decades of on coming cetury is the synthetic fuel-gas derived from coal as a product of coal gasification. It is quite logical to enrich this gas before burning it with natural gas, that is methane, contained in coal measures. Thus it is reasonable to suggest a new concept of unconventional coal mining and utilization technology featuring integrated methane drainage with coal-gas combined cycle. Proposed unconventional technology of coal mining is characterized with: - opening up a coat deposit through boreholes, drilled from the surface and used for coalbed methane drainage as well as for coat gasification in situ; - aggregation of methane producing and coal gasification station on mining side with thermo power plant on the electric power generation side in one integrated industrial enterprise. The further improvement of the conventional coal mining technologies both surface and underground could give only insignificant results in economical, ecological and social aspects, but would not be able to provide basic requirements of the XXI-st century. Significant increase in economical efficiency, cardinal humanization of coal mining and basic improvements in environment protection would be achieved through introduction and implementation of innovative or unconventional coal mining technology. These considerations are applied on both coal production and coal utilization sides as far as coat based energy generation is concerned. Now a general opinion is widely spread that an application in the same manner of the traditional technologies of coal mining and electric power generation would inevitably cause further irreversible damage of the global eco-system, notwithstanding the certain environment protection measures being taken. Keeping the recent pace of the eco-system degradation the whole our civilization would be in danger. Thus the solution of this problem is to be found in developing, promoting and implementing in industry unconventional coal mining and modern advanced clean coal technologies. Coal reserves with favourable conditions at shallow depths are -being rapidly depleted in all countries with developed coal industry. So in nearest future more coat will be mined from deeper levels with higher operational expences and with lower labour productivity. For example in Russia only 20% of proven coal reserves can be specified in quality as easy mined reserves, i.e. coal reserves with a good minability. Unconventional (borehole in situ) coal mining enables us to mine difficult coal reserves, deposited under unfavourable geological conditions with higher economical and socio-ecological efficiency than that in conventional coal mining, in view of these the basic principles and concepts of coal mining and coal utilization for energy generation should be reconsidered taking into account the latest achievments in underground coal gasification/combustion, coalbed methane extraction, clean coat technology and advanced developments in environmental engineering. The authors have developed a new concept of ecologically clean and resource saving coal-gas electricity, protected by a patent of Russian Federation (1995). The main principles and technological features of these conceptual technologies are explained hereupon. It should be a break through into a coal mining technology of new generation, which is known as unconventional coal mining technology. Under current global energy policy, transection to the new generation of coal mining technology is inevitable. Now we are standing at the treshhold of the coat&apos;s regeneration based on integrated unconventional coal mining and innovative coal fueled electric generation technologies.

Feb 24, 1997

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By Alexander J. Verstraeten

Work started on the building of the Amsterdam Concert Hall in 1880 by driving over 2000 wooden piles of 13 m on which foundation-beams out of wood and brickwork were made. During construction the design was changed. This was due to the latest German developments, requiring double walls instead of single, so that the space in between could be used for ventilation and heating. Therefore the pile load, originally designed at approximately 100 kN, increased even to 170 kN for some piles, causing settlements and unacceptable cracks in the brickwork. Settlements of up to 18 cm were measured. In 1985/1986 around 400 vibration-free Tubex-displacement-piles were installed under the Concert Hall, with a shaft of 0355 mm, a pile shoe of 0560 mm and a pile length of approximately 18 m. After these Tubex piles had been installed they took over the complete weight of the whole building, thus eliminating further settlements and damage. 95% of all the construction activities took place while the concerts went on. The chosen solution also made it possible to create a new basement under the Concert Hall as an extension for dressing-rooms etc.

Jan 1, 1987

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By Y. V. Vasylchuk

This paper presents an algorithm for optimizing the classification of surface mine material subject to excavating constraints. High-resolution expected profit models are input and optimized to classification maps subject to site-specific rectangular excavating constraints. This optimization problem defies traditional closed-form analytical solutions; a practical heuristic algorithm has been developed to quickly determine the optimal final destination for the material subject to realistic constraints. The optimization is fast and generates results that achieve up to 98–99% of the total expected profit achieved with free selection. This algorithm provides a fast viable option for practical application in short-term grade control and in managing multiple realizations in long-term resource estimation.

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By A. M. Kiwior

In 1969, the Congress of the United States declared that "the first priority and concern of all in the mining industry must be the health and safety of its most precious resource - the miner," Therefore, Public Law 91-173, Federal Coal Mine Health and Safety Act of 1969, was enacted. Since haulage accidents account for a high percentage of coal mining accidents, Section 314e, ?Hoisting and Mantrips,? was included in the law. This section states: "Each locomotive and haulage car used in an underground coal mine shall be equipped with automatic brakes, when space permits. Where space does not permit automatic brakes, locomotive and haulage cars shall be subject to speed reduction gear, or similar devices approved by the Secretary which are designed to stop the locomotive and haulage cars with the proper margin of safety."

Jan 1, 1975

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note&apos; describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris&apos;s latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d&apos;Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses&apos; and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By William N. Hale

This Bureau of Mines report gives a detailed study of water usage in the Montana mineral industries, along with projections for the future. The mineral industry of Montana in 1963 used 36.5 billion gallons of new water, and reused or recirculated an additional 53.5 billion gallons for a total water requirement or usage of 90 billion gallons. The petroleum industry was the major water user, followed by the copper and zinc industries. Many mineral industry operators provide their own water, and new water is withdrawn largely from surface sources. At present, sufficient water is available in rivers, streams, and reservoirs in Montana; however, shortages do exist locally near mineral industry operations using large quantities of water. Some is supplied from sources up to 44 miles distant. New water withdrawn by the State of Montana mineral industry is expected to increase from 36.5 billion gallons in 1963 to 51.1 billion gallons by the year 2000. The total-water requirement is expected to more than double, or reach 182 billion gallons by the year 2000.

Jan 1, 1966

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it &apos;is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By F. S. A. de Frey

The main users of computerised financial evaluation tools in the mining industry are the mining investment analyst, the mine manager together with his financial manager and the mining student (undergruadate and post-graduate). The mining investment analyst&apos;s needs mainly centre around the-micro and macro aspects affecting the mining industry in general. The mine manager needs a tool to assist him with the planning, reporting and controlling of production, costs, efficiency, productivity and cashflow. For the mining student studying Financial Evaluation, the main need is for a computer program which will assist him in learning the basics of the subject. This paper concentrates on the needs and objectives of the course Financial Mine Evaluation, the approach to which is presented. Emphasis is placed on the practical computing sessions and the role of the FCS-EPS package as a training tool.

Jan 1, 1987