Search Documents

By H. A. D. Kirsten

Shotcrete has become a strategic component of support in underground mines. The ductility of reinforced shotcrete makes it a safe and economic means of surface support under adverse static and dynamic loads. The ability of ductile shotcrete to sustain load at large deflections enables excavations in squeezing conditions to be stabilized and the safety in excavations subject to rock bursting, to be assured. A Shotcrete Working Group was formed to find the configurations of fibre reinforcement that would give shotcrete the same ductility as when reinforced with mesh. Beams and panels reinforced with various types and lengths of fibre were accordingly tested. A single mix design consisting of river sand, ordinary Portland cement, fly ash, condensed silica fume and gunite dust and segregation suppressant was used. Steel and polypropylene fibre varying in length from 25 to 50 mm were used in nominal contents of 5 % and 0.5% by mass respectively. Beams, panels and control specimens were shot into specially made formers. Suitable mixing procedures were developed for the different types of fibre. The test specimens were shot in a semi-dry mix process. The shotcrete was cured until tested 28 days after shooting. The fibre contents and uniaxial compressive and Brazilian tensile strengths of the shotcrete were determined from the control specimens. The beams and panels were tested in bending in specially manufactured test rigs. The beams were examined for simple supports and fixed ends. The panels were fixed in a manner that simulated underground conditions and were loaded statically under uniform pressure. The beams were loaded and the corresponding deflections measured up to failure. The panels were loaded up to mid-span deflections of 150 mm. The results are presented in the form of load-deflection graphs. The peak loads and ultimate deflections for the fixed end beams were considerably larger than for the simply supported beams for the various types of fibre considered. None of the beams tested, however, were able to sustain load at relatively constant value beyond the peak load. The panel tests showed that 40 mm and 50 mm long steel fibre and 30 mm, 40 mm and 50 mm long monofilament polypropylene fibre reinforcement gave shotcrete the same ductility as mesh.

Jan 1, 1998

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

By S M. Loewen, J J. Fuykschot

Located in the north-west of Kazakhstan is a world-class podiform chromite deposit. Donskoy mining and beneficiation complex (DGOK), a branch of Kazchrome TNC, which is a subsidiary of the Eurasian Resources Group (ERG) operates two underground mines in this area, one of which is the ‘10th Anniversary of Kazakhstan Independence’ (DNK) mine.The mine currently applies the gravity caving mining method, producing 1.8 Mt/a of ore utilising a slusher layout and rail transport to the hoisting shafts. The deeper zones form the largest mineral resources at the DNK mine and are planned to be developed in the next several years. At this depth, the generally poor ground conditions, combined with the high in situ stress state will potentially lead to extremely challenging mining conditions.This paper describes a technical study undertaken by SRK to determine the possibility of increasing the maximum production rate from the currently envisaged 6.0 Mt/a to 7.2 Mt/a, and to reduce the time taken to steady state production.Based on a newly created 3D model, the inclined caving method was proposed for the largest orebodies. This method, presently not implemented at any operating mine, although planned for two other projects, was deemed very suitable to deal with the weak rock mass characteristics and the plunging morphology of the mineralisation.Dassault Systèmes’ GEOVIA’s Footprint Finder software (a module of GEOVIA’s PCBC™) was used to determine the caving zones and production schedules. The total mine design was completed in Deswik software, and resulting schedules combined in Excel.In addition to the use of an inclined caving method, several other suggestions were made to increase the productivity of the mine, such as the application of a conveyor belt system transporting multiple material types, teleremote technologies and the application of thin sprayed liners to reduce the swelling of the rock mass.CITATION:Fuykschot, J J and Loewen, S M, 2016. Inclined caving option for the DNK mine, Kazakhstan, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 669–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

"The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media. Due to the lack of higher precision influence of temperature on thermal conductivity, we took 6 groups of experiments on rock samples (including igneous rock, sedimentary rock and metamorphic rock) under different operating temperatures from 20? to 50? by 7 acquisition points. The general equation of thermal conductivity drives the value of it increasing along with the decreases of the temperature. While in our experiments, it is easy to find a singularity among them for each sample. The experimental investigations we attempted to observe and interpret the alteration mechanism. According to the Heat Capacity Theory in solid state physics, this research gives the explanation about the “singularity” from 3 understanding of specific heat, average free path, and thermal conductivity. Our research divided the condition of the rock thermal conductivity into 3 different types. INTRODUCTION The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media(Huang & Han ,1988; Peierles ,1955). This parameter is necessary for analysis of heat transfer(Vaferi et al, 2014;Hans-Dieter & Rudiger,2003). It’s well known that a general equation for ?(T) was set by Sass et al. (1992) which based on the coupled effect of composition and temperature on the thermal conductivity(Jesse et al, 2013; Mongelli et al,1982).The equation was further successfully verified for other rock (Zumrud et al,2010;Abdulagatova et al,2009;Seipold& Huenges,1998).Thermal conductivity is also related to other physical proper ties of porous rock, such as thermal diffusivity, heat capacity(Brettmann et al,2011;Abuel-Naga et al,2008). It is well known that ETC and other thermo physical properties of rock materials are affected by various factors, such as temperature, pressure, mineralogical composition, porosity, stratification, size and shape of the components, and nature of pore fluid, etc. (Tiedje & Guo, 2014; Touloukian et al,1970).The understanding of heat transport processes still requires the knowledge of thermal properties of rocks."

Jan 1, 2015

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By G. S. Camm

Gwynfynydd is a small, high-grade black shale-hosted vein-gold deposit. The Chidlaw Link Zone is the only area being mined and contains 24 000 t ore grading 15.2 g/t gold. Within the Link Zone a complex vein structure occurs consisting of a mother vein up to 5 m thick and narrow (less than 0.5 m) leader veins. The former shows minor variations in dip, strike and thickness, whereas the latter show marked changes in all three. The leader veins are hosted within the footwall zone of the mother vein and both are composed of quartz with galena, sphalerite, chalcopyrite, pyrite and minor arsenopyrite. The vein system is transected by a series of cross-vein and intra-vein dip-slip faults. Pockets of gold occur at vein intersections or branches and within the complex footwall zone and are often related to variations in vein attitude and/or geometry. The Chidlaw Link Zone displays a complex, erratic distribution of gold mineralisation and a multi-stage history of structural activity, fluid flow and mineral deposition

Jun 18, 1905

By J. Konnerup-Madsen, T. Unlu, H. Stendal

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The region includes the Deveci siderite/goethite deposit and the Hasancelebi, Karakuz and Kuluncak magnetite/goethite deposits; Deveci is the only mine in operation. The area consists of a serpentine-gabbro complex overlain by a volcano-sedimentary sequence hosting the iron ores. At least three generations of hydrothermal alteration have affected all rock types except the latest trachytic dykes. The Deveci deposits occur in a pyroclastic volcano-sedimentary sequence with shales and carbonates equivalent to the main mafic sequence, whereas the other three deposits formed contemporaneously with the intrusion of trachytic dykes. The deposits are of the volcanic-exhalative type, with syngenetic siderite in pillow lavas or stratiform layers the primary and main Fe-bearing mineral. In the west hydrothermal alteration has replaced siderite in pillow lavas with magnetite or has remobilised sideritic iron into magnetite veins

Apr 1, 1995

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By Joseph Gersic

MINFO has been developed to serve as a frontend for three databases created to store basic minerals information gathered during the minerals resource assessment conducted by U.S. Bureau of Mines(USBM) for the Malheur and Jordan resource areas of southeastern Oregon(MJRA). The primary database is the Minerals Location Inventory (MLI.DBF) which contains of information assembled from field work performed during this project, the USBM Minerals Availability System/Mineral Information Location System(MAS/MILS) database, the Oregon Department of Geology and Mineral lndustries(DOGAMT) Mineral Information Location(MILOC) database, and the U.S. (Geological Survey(USGS) Mineral Resource Database System(MRDS), In addition, assay results are contained in the geochemical database (ELEMENTS.DBF) and modified X-ray diffraction analysis information is contained in the minerals database (MINOR.M.DBF). MINFO includes four types of program modules: ? Enter/Edit Data was developed to allow the addition of new information and to encourage correction of errors by providing a convenient means of entering and editing data and a large degree of automatic checking and filtering of entries. ? ACAD/DBF Link links each site symbol posted on the map in the drawing file to a record in the database. This provides the user with the ability to use a mouse or other pointing device to graphically select a site for viewing and editing. Edits are performed directly in the database file, ? Reports contains 7 formats of data output for creating files for printing, transfer to other database formats, and exporting to other software packages such as spreadsheets and word processing programs. ? Maps includes 5 programs for creating AutoCAD script files which can be used to create maps of selected information in conjunction with AutoCAD. Mineral location mapping files derived from MLI.DBF can be created in 2 formats. Mapping files can be generated from each of the 2 sets of geochemical analyses contained in ELEMENTS.DBF. X-ray diffraction analyses can also be translated into instructions for creating and posting piecharts at sampling sites.

Jan 1, 1994

By Anderson Ayres Bittencourt

O monitoramento de sistemas e ativos de automação sempre existiu de forma rudimentar e descentralizada. A análise desses dados tanto quanto sua obtenção é um desafio para as empresas atuais. Foi a partir deste princípio que nosso projeto foi desenvolvido.Este trabalho tem como objetivo demonstrar a solução de Monitoramento online e preditivo implementada na ArcelorMittal Aços Planos da América do Sul, onde desde o início de sua implementação pudemos capturar benefícios operacionais, melhoria dos processos, otimização, eliminação e/ou diminuição de indisponibilidade de plantas, entre diversos outros retornos que serão apresentados.

Oct 30, 2017

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By José Arango

El presente texto describe la aplicación del sistema MIMS en las estadísticas de producción de la Sociedad Minera Cerro Verde S.A. El sistema fue instalado inicialmente para el control de mantenimiento de los equipos, movimiento logístico, y contable. Posteriormente, se realiza el cambio del sistema de información manual a un sistema computarizado, donde se analiza los problemas cotidianos del sistema de información antiguo y se los compara con los cambios experimentados. En ese sentido, el objetivo de este sistema es facilitar el alcance de sus metas a la organización mediante el uso eficiente de todos sus recursos disponibles: personas, información, equipos, tecnología, y materiales diversos. La eficiencia de la utilización del recurso de información es medida por la relación del costo para obtenerla y el valor del beneficio derivado de su uso.

May 25, 1998

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905