Search Documents

By A. J. Sideris

It is known that Mg can act as a catalyst/solvent in the high pressure high temperature diamond synthesis. However, above pressure levels of the order of 7 GPa, and temperatures from 1700 ? 1800oC, it was not possible yet to use Mg for the industrial production of diamond. A possible alternative is the use of MgNi based alloys. However, owing to the great Mg reactivity, it was consider, so far, a difficult task to deal with such alloys. The present work presents successful results regarding the production of MgNi alloys, with different composition, at high pressure conditions. The behavior of the alloys and their microstructural characterization is analyzed.

Jan 1, 2006

By B. F. Naylor, C. H. Shomate, F. S. Boericke

"Ilmenite is the most important titanium-bearing constituent of titaniferous iron ores. Such ores, of which the United States has abundant reserves, are of interest because they constitute an important potential source of both iron and titanium that may be tapped in times of stress, and which eventually may be utilized in the normal course of events.As the iron and titanium constituents of titaniferous iron ores are not completely separable from each other by ore-dressing methods, any process for metal recovery will, of necessity, involve reduction of the iron in ilmenite. Consequently, knowledge of the thermodynamic properties of ilmenite should supplement information already available concerning those ores. With this in view, the Pacific Experiment Station of the Bureau of Mines undertook to evaluate thermodynamic properties; the data obtained are the subject of this report.Three types of experimental work were involved. First, low-temperature specific heats of ilmenite were measured in the temperature range 500 to 29S° K. These data serve to evaluate the entropy, a quantity necessary for a reliable evaluation and correlation of other thermodynamic properties. Second, high-temperature heat-content measurements were made in the temperature range 298° to 1,743° K. The data serve to bridge the gap between room temperature and elevated reduction-process temperatures. Finally, hydrogen-reduction equilibria were measured in the temperature range 1,220° to1,375° K. These data-give a direct measure of the free energy of reduction of ilmonite at these temperatures and, in conjunction with results of the other two types of measurements, serve to obtain the heat of formation of ilmenite, a quantity not readily determinable by direct calorimetric means.The data are correlated to form a composite, self-consistent portrayal of the thermodynamic properties of ilmenite, which may be used in evaluating the efficacy of any reducing agent of known thermodynamic properties. Selective-reduction of iron in ilmenite by hydrogen, carbon monoxide, and carbon are considered in this report."

May 1, 1946

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014

By William R. Yernberg

The combined 76th Annual Minnesota Section of SME meeting and 64th Annual University of Minnesota Mining Symposium were held April 8and 9, 2003, in Duluth, MN. This year’s theme was “Stakeholders, Partners in Change.” The meeting included four keynote speakers, technical presentations and a tradeshow. Engineers, executives, mining managers and suppliers from throughout the United States and eastern Canada attended the meeting. Reflecting the theme of the meeting, all agreed that the mine owners, the government, the community and the employees are all “stakeholders.” They must be “partners in change” for the iron ore mining industry to survive in the region. Compared with past meetings, where improved technology was the primary focus, this year the focus was on the dramatic restructuring of the entire industry. As noted by several of the speakers, “This time, the change is not in technology.”

Jan 1, 2003

By J. C. Johnson

Underhand mining with cemented mill tailings for backfill has proven to be a safe and effective alternative to conventional overhand mining for rockburst prone mines. The ability of the cemented sandfill to survive a rockburst shock wave without failing has been observed at mines in the Coeur d?Alene Mining District many times in the last twenty years. To better understand the dynamic loading of this commonly used support material the National Institute for Occupational Safety and Health (NIOSH) performed laboratory experiments using a split Hopkinson Pressure Bar (SHPB) to quantify the maximum stress and energy absorption of cemented mill tailings from the Galena mine. Cylindrically shaped cemented backfill specimens aged 28 days were placed in the split Hopkinson pressure bar testing apparatus and a dynamic load was applied. The measured peak dynamic compressive strength of the cemented sandfill was 10.6 MPa (1540 psi) and is approximately twice the static unconfined compressive strength (UCS) of 5.5 MPa (800 psi). These test data showed about 95% of the initial energy was reflected away from the backfill and only 5% of the energy was absorbed. This may help to explain why backfilled stopes could withstand seismic events up to 3.5 Richter magnitude (Ml). When a compressive rockburst wave impacts a stope a large amount of the stress and energy is reflected away. The reflected wave is a tensile wave which creates tensile cracks and spalling in the entire wall of the stope. The backfill supports the damaged wall rock and holds it in place. Some of the stress and energy of the rockburst is transmitted into the backfill and because the backfill is being dynamically loaded it has a strength that is twice its static value and absorbs a substantial amount of rockburst energy. Although mining in deep underground mines is an extremely hazardous occupation, the use of underhand mining with cemented backfill for static and dynamic ground control increases the safety of the workers.

May 1, 2007

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By Suk han Jang

This paper describes the tower foundation design and construction experience for the 345kV Youngheung marine transmission line, which has been in commercial operation in Korea since July, 2004. This transmission line was designed and constructed to meet the rapidly increasing power demands of metropolitan areas and supply stable, bulk electric power from the Yonghung thermal power plant into metropolitan areas. This transmission line passes over the west sea, Lake Sihwa and over land. In order to successfully complete this project, and to safely support the tower during severe maritime conditions, several types of tower foundation such as Pad and Chimney foundation, Pier (Cylindrical) foundation, R.C.D foundation, Jacket pile foundation and Steel pipe pile + concrete mat foundation were developed and used. As the world?s first and longest marine transmission line, the 345kV Yonghung marine transmission line operates successfully, thanks to several high-tech civil engineering technologies and KEPCO?s accumulated experience.

Jan 1, 2007

By S. Y. Tan

As continual complementary metal?oxide?semiconductor (CMOS) scaling requirements, metal gate/high-k dielectric/Si gate stacks are expected to replace poly-Si/SiO2/Si gate stacks in the future CMOS sub-45 nm technology node. Hafnium based oxide is a promising candidate to replace SiO2 as a gate dielectric, due to its much higher dielectric constant (high-k) and stability. The key challenges of successfully adopting the high-k dielectric/Si gate stack into advanced CMOS technology mostly come from the interfacial properties. The origins of the electrical and physical characteristics of the dielectric oxide/bulk interface were studied in detail. The leakage current density-voltage (J-V) and capacitance-voltage (C-V) measurement techniques were employed to study the dielectric oxide/Si interface. The effects of the post-deposition annealing (PDA) treatment on the interface charges of dielectric oxides were studied. We found that the PDA can effectively reduce the trapping density and leakage current, and eliminate hysteresis in the C?V curves. Besides, the changes in chemical bonding features at HfO2/Si, HfSiO/Si and HfSiON/Si interfaces due to PDA treatment were evaluated by XPS measurements. The XPS analysis provides a better interpretation of the electrical outcomes. As a result, both HfSiO and HfSiON films have exhibited superior performance in terms of thermal stability and electrical characteristics.

Jan 1, 2010

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By D. Kruse

Top down constructed large diameter (up to 90 m [300 ft]) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to: analyze various failure modes, evaluate the shaft liner and internal structures? response to seismic loading, assist in segment design, and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly, and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored.

Jan 1, 2011

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By B. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 2005 at a record $758 million (21 percent of the total non-fuel mineral production of Utah). Major commodities produced in 2005 include salts (halite, potash, and magnesium salts), Portland cement, sand and gravel, carbonates (lime, limestone, and dolomite), phosphate, crushed stone, clays, lightweight aggregate (expanded shale and perlite), gypsum, silica, sulfur and sulfuric acid, and building stone. Commodities produced in smaller amounts include diatomite, pumice, gemstones, ornamental stone, fluorspar, and mineral and fossil specimens. Utah is in a period of rapid growth in industrial rock and mineral production; however, some commodities have grown faster than others. The robust western economy has stimulated production of construction-related commodities like sand and gravel, Portland cement raw materials, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants

Jan 1, 2007