Search Documents

By James D. Navratil

Although liquid membranes have several advantages over conventional liquid-liquid extraction, problems such as membrane instability remain. In order to solve these problems, we have combined an electrostatic field with the principle of liquid membranes and developed a novel reactor system for rare earth recovery. Our cylindrical reactor, filled with extractant and diluent, is divided by means of a perforated cylinder into an outer annular extraction cell and an inner stripping cell. Below the extraction and stripping cells are two settlers for the aqueous solutions. The design of the reactor permits the organic solution to flow freely through the special perforated cylinder and the added feed and strip solutions, outside and inside the perforation, respectively, to be completely separated.

Jan 1, 1990

By A. V. Tarasov

An environmentally clean and virtually waste-less technology for treatment of domestic solid waste and other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations. The proposed process resolves the acute and globally significant problem of dioxin formation. The purpose of the proposed technology is to ensure such destruction of the structural lattice of toxic compounds that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. The preconditions that are required to achieve this purpose are: temperature of >125O0C; an oxidant excess coefficient of >I .05; a certain retention time of the products under these conditions (ADZ s); and thermal instantaneousness of the process involving a transition with no intermediate phase. These conditions were achieved with the experimental development of the Vanyukov furnace design commonly used for sparged smelting processes at non-ferrous metallurgical plants in Russia and Kazakhstan.

Jan 1, 2002

By P. A. Botha

The coal seams in the Waterberg basin occur in correlates of the Vryheid and Volksrust Formations as developed in the main Karoo basin. In the Vryheid Formation, five thick seams of predominantly dull coal are present, whereas a multitude of thin, lenticular seams (a few millimetres to 2 metres}, predominantly of bright coal, are developed in the overlying Grootegeluk Formation. During exploration, the coal seams were divided into 11 zones. Analytical data on float and middlings fractions (RD less than 1.40 and between 140 and 1.80, respectively} were used mainly for stratigraphic correlation of the zones in the Grootegeluk Formation. The affinities of the major and trace elements for different mineral phases and/or organic material are discussed on the basis of correlation matrices and vertical variation diagrams. Titanium and vanadium clearly show some degree of organic affinity. P 205' AI203 and alkaline-earth elements are also positively correlated by the presence of goyazite in the coal. This type of investigation gives an indication of the degree to which undesirable elements like P and S can be removed during coal beneficiation, of which coal zones are unsuitable for the production of metallurgical coal on account of a high content of these elements, and to what extent the blending of different coal zones is required to keep the concentration of these elements within acceptable limits.

Jan 1, 1991

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By Kuiting Wang, Jinshan Liu, Ninglei Sun, Aiguo Dong, Yeda Lu

"Eliminating the environmental threat caused by waste effluent containing magnesium sulfate derived from the process of nickel laterite sulfuric acid leaching and subsequent nickel precipitation is always a focus in the metallurgy field. A new flowsheet whose procedures include vaporization, crystallization, two stages precipitation of magnesium, causticizing treatment of filtrate and ammonia recycle was investigated. Both the details of the flowsheet and its application are described in this article. It is confirmed to be an effective and economical method to prevent the pollution by the waste effluent, simultaneity, a series of magnesium products recovered during the process own good economic returns.IntroductionSulfuric acid leaching is the conventional procedure of extraction valuable metals from ores in hydrometallurgy field. During the process of nickel laterite sulfuric acid leaching, several metals, including Ni, Co, Al Mn, Fe, Mg etc., migrate into the leachate in the form of soluble metal sulfate. After subsequent procedure of purification, precipitation of Ni and Co and neutralization, an enormous stream of waste effluent which contains a concentration of approx. 15-40g/L Mg is exhausted. Such solution containing magnesium sulfate is toxic, which causes diarrhea for both human and animals. On the other hand, large amount of sulfate acid was consumed during the process of leaching by the compound of Mg, which increases cost of a hydro nickel plant.In arid areas, the waste effluent mentioned above is treated via evaporate pond owning large acreage, which needs not only the appropriate meteorologic condition, but occupies much land. In coastal areas, it is directly discharged to the sea, which probably deteriorates ecological system of offshore strip. The most widespread method to treat with the waste effluent is neutralization by lime cream, the residues of which containing magnesium hydroxide and gypsum are transported to residues pool. Neutralization is a simple process, but it never recycles the Mg and sulfate anion into new application, meanwhile, the residues are potential threat to the environment."

Jan 1, 2012

By B. Sereda

As it is known the creation and development of new titanic alloys has been problematic up to now. They can be used in aircraft and vehicle construction, shipbuilding and as materials for keeping static loadings in high-temperature environments. In this work the synthesis of various titan aluminides is investigated. Mathematical model of structurization process was done. On the base of retrieved model the mechanisms of structurization in systems Ti + Al and Ti + 3Al was determined. Experimental researches were done at two different modes: burning and thermal spontaneous ignition. The method of retrieving compacted products combusted in SHS conditions (SHS-compacting) was used to gain these intermetallic compounds. The physical and thermal characteristics of technological process and their influence on structurization, homogeneity of structure and porosity of titan aluminides have been simulated and researched. It is established that the SHS-compactizing technology is fully capable of supervising the process of structurizations with the whole complex of advantages and can be applied for receiving qualitative titan aluminides with the set of chemical-physical properties.

Jan 1, 2010

By Congcong Yang, Jian Pan, Deqing Zhu, Yang Zhong

A study of pelletization of one imported chromite concentrate with coarse site, poor ballability and refractory roasting performance was conducted in small scale tests, and high pressure grinding rollers (HPGR) was used to improve the pelletization. The mechanism of HPGR was revealed by means of SEM images and optical microscopy. Compared with the ball milling pretreatment, HPGR pretreatment can not only enhance the ballability of pellet feed but also drop the roasting temperature. Fired pellets, containing proper chemical compositions with high compressive strength of 2917N/pellet and good metallurgical performances, have been manufactured. The mechanism of HPGR reveals that chromite particle surface turns to more irregular after HPGR treatment and more new surface being formed because of more cracks, sharp corners and edges appearing, resulting in higher surface chemical activity, all of which improve the ballability of the chromite concentrate and contribute to the consolidation of fired pellets.

Jan 1, 2015

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By Roberto Parra

The operational control in a Flash Smelting Furnace is based on the mass and energy balance of the chemical and mineralogical composition of the concentrates. It is well known that many troubles in the dust formation and slag quality occur without a clear correlation to a specific process parameter such as the matte grade or heat balance. This paper outlines two new considerations that could both help improve the entire quality of the process: blend characterization and versatile slag composition control. Related to the blend control, laboratory scale study has shown that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of2 or 3 types of concentrates can be identified. Related to the control of stag composition, the quantification of the slag liquidus temperatures and viscosity could be an effective operational tool for both for ferrite and fayalite slag that can also directly help deciding the blending parameters. From these viewpoints the benefits of the combination of these two approaches for high temperature operation is discussed. Keywords: Optimization, Copper concentrates, Flash combustion, Blends, Slag composition

Jan 1, 2003

By Carlos G. Levi

"The principles involved in the rapid solidification of supercooled metal droplets and existing numerical models are reviewed. The limitations of these models for studying alloy solidification are discussed in terms of the effects of alloying elements on the relevant heat transfer, thermodynamic and kinetic parameters. Analysis of the enthalpy-temperature diagram reveals how the extent of rapid solidification is hindered by the addition of solute. A solidification model incorporating thermodynamic and kinetic relationships into a Newtonian heat transfer formulation is used to analyze the thermal history and concurrent solute redistribution during recalescence. IntroductionIt is well acknowledged that microstructural evolution during solidification is intimately associated with the thermal history of the liquid-solid interface. Structural parameters like chemical homogeneity, morphology and size scale of the phases can be related to the interfacial temperature and velocity. These in turn change by the interaction of the interface with the thermal and solutal fields in its neighboring environment.The thermal history of powder solidification can be conveniently described on the enthalpy-temperature diagram for a pure metal shown in Figure 1 and discussed in detail elsewhere [1). A system can conceivably follow any path of decreasing enthalpy in the supercooled region of Figure 1 (~ < 1), starting at the nucleation temperature (oN < 0) on the liquid line, and ending at some point on the solid line. A vertical path represents an isothermal transformation, of which a limiting case is solidification without significant barriers to nucleation and growth, with the interface at the equilibrium temperature TM (path one in Figure 1). A horizontal path represents isenthalpic (or adiabatic) solidification whereby the system could form an amount of solid proportional to the initial supercooling of the liquid without further heat loss to the environment. A liquid that can completely transform to solid under adiabatic conditions is said to be ""hypercooled""."

Jan 1, 1986

By Hal dun Kurama

In thus-study, Bigadic upper zone zeolitic tuff, which contains about 87% clinoptilolite was used as an ion exchanger for removal of Pb++, Cu++, Cd++ and Hg++ ions from wastewater. Bench scale experiments with two different glass columns, were carried out continuously under the closed/ open circuit conditions. Before ion exchange tests, zeolite samples were treated with NaCI (6ml/ min. and 42BV). The effects of particle size, bed volume, pH and flow rate on the ion exchange capacity were determined. Under the best operation conditions, the effect of initial influent solution concentration on ion exchange selectivity was tested. As a-result, it was found that the Bigadiç clinoptilolite had the following ion exchange capacities;

Jan 1, 1995

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By Jitka Jandová

In this study, hydrometallurgical processing of waste ZnO flue dust arising during zinc removal from galvanized low-alloy steel sheets was investigated on a laboratory-scale to obtain electrolytic zinc. The flue dust was separated from flue gases, generated during heating waste galvanized steel sheets in an electric furnace under air atmosphere at temperatures of about 1000oC. The dust, comprising tetragonal ZnO and insignificant amounts of SiO2, was contaminated by Fe, Mn, Pb, Al, Mg, Pb, Cu and Ca. The dust was leached in 0.5 and 1.0M H2SO4 and/or in 20 and 30% NaOH at different temperatures and different liquid-to-solid ratios to determine the optimum conditions leading to the highest possible selectivity of leaching and efficiency of Zn extraction in minimum time. The subsequent electrowinning process was performed with refined zinc sulphate leach liquors and/or with untreated zinc caustic solutions. Zinc sulphate leach liquors were purified using a combination of a hydrolytic pH-controlled precipitation, cementation and carbon refining. Effects of operational variables on Zn electrowinning have been studied for both sulphate and caustic electrolytes. The conventional plate-plate electrowinning cell has been explored in this study. Comparison of results obtained for both zinc electrowinning from acid sulphate and alkaline solutions is presented contribution.

Jan 1, 2003

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006