Search Documents

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Roof stability in the belt entry is critical for safe and continuous production of coal during longwall mining. Previous studies of roof falls that occurred in belt entries have shown that the roof falls were largely associated with high in situ and longwall-induced horizontal stresses [1,2,3,4]. To properly support the roof in a belt entry, it is important to understand how longwall-induced horizontal stress changes can affect roof stability in the belt entry. Monitoring of horizontal stress changes was conducted in the belt entries of two Pittsburgh seam longwall panels oriented unfavorably to the major horizontal stress. Numerical models were also set up to investigate how horizontal stress concentrates and relieves in the belt-entry roof near the face as panel orientation changes. Both measurements and modeling results show that high horizontal stress concentrates in the belt entry roof within about 15 m outby the face. The study demonstrates that longwall-induced differential horizontal stress can be used to evaluate the horizontal stress concentration factors. The horizontal stress concentration factors change with panel orientation, resulting in high stress concentrations at orientations between 20 and 110° and low stress concentrations between 130 and 180°. Roof support strategies are given for the belt entries under the influence of high horizontal stress. For unfavorably oriented panels in weak roof conditions, supplementary support should be installed during development, and cable bolts should be anchored into a stable roof horizon. The bolting pattern should be designed to cover both entry corners and the entry center to prevent potential roof cutters and sagging.

Jan 1, 2023

By Joe B. Rosenbaum

Waste solutions from sea water desalination processes are enriched in minerals by a factor of two or three. This suggests that extraction of selected mineral components from the concentrated brine might help pay desalination costs. The possible recovery of gold has received particular mention. Sonstadt, in 1872, reported the gold content of sea water as 65,000 micrograms per cubic meter, or 65,000 parts per trillion. At $35 an ounce, this is equivalent to $0.065 per ton of sea water. Fritz Haber, however, after his abortive venture to restore Post War I Germany to economic health by recovering gold from the sea, concluded the gold content was 4 micrograms per cubic meter. Haber's analysis is equivalent to 0.0004 cent per ton. In the past 10 years, investigators using advanced analytical techniques reported from 4 to 27 micrograms per cubic meter. Our brief experiments to determine a threshhold value for the gold in sea water employed solvent extraction for initial concentration, evaporation of the gold-loaded organic for further concentration, and atomic absorption analysis of the gold in the concentrated organic. Radioactive gold was used as a tracer for monitoring the gold through the concentration and analytical steps. Our method established that sea water contains about 11 parts gold per trillion parts sea water, or 0.001 cent worth per ton. This agrees closely with results of recent studies by other investigators employing ion exchange resins and neutron activation techniques.

Jan 1, 1969

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By Y. J. Wang

Optimal sizing of a ventilation shaft is a classical subject in mine ventilation economics.. The shaft size is optimized by minimizing the sum of shaft-construction and ventilation-power costs, or owning and operating costs. The length and air quantity of the shaft are held constant, and the location of the shaft, affecting its depth, and construction and ventilation power costs, is not considered (Hartman, 1961; Lambrechts, 1974; Wang et al., 1978). This paper proposes an approach by which the location and size for a new pair of shafts (intake and return shafts) are optimized for a coal-mine ventilation network. Specifically, the problem is to determine the location and size for a new pair of shafts, and the distribution of air between the new and old shafts so that the combined cost of shaft construction and ventilation power is minimized. The shaft length or depth corresponds to the height of overburden at any shaft location. To simplify the problem, the shaft locations will be limited to the line along the main or submain entries, and the connection entries at the shaft bottom neglected. In order to calculate the ventilation-power cost, the air power of the system should be determined. This in turn requires the calculations of the air quantity and pressure of each fan in the network, satisfying Kirchhoff's laws and Atkinson equation. After obtaining the air power, the cost calculation is straightforward. In the following, we shall assume that the resistances of all airways, and the quantity for each mining section, which is controlled by adjusting the air regulator, are all known. The resistances for the shafts are determined from the estimated friction factors, and shaft dimensions and lengths. Furthermore, it will be assumed that the fans can be selected to meet the duties called for by any network solutions.

Jan 1, 1982

By Heinrich H. Becker, Vladimir L. Konyukh, Sergey P. Koltsov, Valery A. Davidenkol

Ramifide conveyor transport of the biggest russian coal mine "Raspadskaya" is simulated by Petri nets. There are 6 longwalls with accidental output. 12 belts, and 5 transfer bunkers at this mine. It is necessary to coordinate transport links for recon- structed conveyor system. Many tasks were solved by dynamic simulation, such as estimation of transport lateness, influence of transfer bunkers on an unevenness of total coal flow, maximum filling of each bunker, maximum time of main conveyor refusal, co-ordination of unloading for dependent bunkers, choice of main conveyor. The problem of mine-wide conveyor transport animation for dispatcher is formulated in reference to mine "Komsomolets". OBJECT OF SIMULATION The biggest russian coal mine "Raspadskaya" is situated on a south part of Kusnetski coal basin (West Siberia). One mines about 20.000 tons of coal out of flat seams by 2.2-4.5 m thickness in a day. There are 6 fully- mechanized longwalls by output 720- 3600 tons in a shift in mine. Coal haulage to surface is carried out by 12 belts having 1.6 - 4.3 km length. For a smoothing over un- evenness of coal flows 5 transfer bunkers to 300 tons were intro- duced. The designed conveyor system is divided into two parts (Figure 1). In the upper part some coal from Face 1 comes through belt road C, into transfer bunker 8,. From the opposite side that bun-

Jan 1, 1996

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Thomas O’Neil

Part 2 of this article continues with a discussion of features that distinguish contemporary investment analysis in mining from earlier methods. Part 1 traced the evolution of evaluation methodology from the traditional and discounted cash flow methods to the present. Quantitative investment models of the past 20 years played an important role in mine evaluation, but a new integrated approach to mine investment decision-making is now developing because of growing economic, technical, and political uncertainties. One of those uncertainties -inflation-was discussed in Part 1. Increased Risk At a time when mineral production technology and analytical evaluation tools have never been more sophisticated, it may seem anomalous to claim that mining ventures are riskier. Whereas technical risk has, indeed, been notably reduced, business risk the chance of a major loss due to market factors-has increased. This has been caused by two factors: the rapidly rising capital requirements of new projects and increasingly unpredictable future economic conditions. These difficulties are compounded by the long lead times of large, new mining projects. Rising Capital Requirements A $100 million investment is no longer considered to be a large mining project in most cases. For a large metal mining project, the total cost of the concentrator alone can exceed $100 million. Amoco Minerals' Thompson Creek molybdenum mine being developed in Idaho will cost over $350 million, for a relatively modest sized (23-kt/d or 25,000-stpd) ore operation with no extraordinary features. For a major grass roots copper operation producing blis¬ter or refined copper, the capital requirements are billions of dollars, not millions. Project costs are higher for two reasons. One, the projects themselves are larger; and two, the capital cost per unit of production is rising rapidly. Projects are larger because lower grade ores, yielding smaller margins, must be mined in greater volume-particularly in view of the high fixed costs of modern technology. When analysts contemplate any capital project, an important consideration is the minimum economic size of the facility. This is the smallest size that can be built and still be competitive on a total unit production cost basis. In the conventional copper smelting business, for example, a production rate of at least 91 kt/a (100,000 stpy) of blister copper is about the absolute minimum for reducing unit fixed costs to competitive levels. Clearly, many variables affect the minimum economic size of a mining facility, but with few exceptions that size continues to grow. Unit capital costs of new mining projects also are continuing to rise. The accompanying table shows that the capital costs in primary copper production have risen faster than the cost of living. Of particular note is the capital charge of over $1.70/kg (77411b) required for a new, fully integrated facility in 1981. Thus, the mid-1982 copper price would not even cover the cost of capital for a new copper producing complex without considering the direct operating costs for such a facility. The breath-taking costs of new mining projects are caused by factors such as increasingly complex technology, the rising social costs of creating attractive living and working conditions for employ¬ees, and the expenditures re¬quired for environmental protec¬tion. For whatever reasons, how¬ever, unit capital costs in mining continue to exhibit staggering growth rates. Future Economic Conditions Risk is not only a function of the size of the potential loss-an im¬portant measure of which is the capital intensity of mining dis¬cussed above-but also of the like¬lihood of incurring the loss. It is here that the ever increasing lead times of mining projects and the glaring limitations of economic forecasting are so important. In comparison to nearly all other in¬vestments, mining has more capi¬tal at stake for a longer period of time before commercial uncer¬tainty is resolved by distant eco¬nomic conditions that are subject to high forecasting errors. A sobering example of the pre¬ceding points occurred with the Lakeshore copper mine in south¬ern Arizona that Hecla Mining Co. undertook to finance and manage in 1969. The project was a joint venture of Hecla and the El Paso Natural Gas Co. and included two mines-one producing oxide ore and a second in the sulfide zone¬and a complex processing facility producing both electrowon cop¬per cathodes and copper precipi¬tates. The project originally was

Jan 12, 1982

By Carlos Fonseca, Gustavo Usero, Roberto Mentzingen Rolo, Gabriel Moreira, Octavio Rosa de Almeida Guimarães

Geological domain modeling is an important step in mineral resources evaluation. The procedure can be laborious and time-consuming, especially in multivariate settings. However, estimates are significantly improved when carefully limited by geological variables. This paper proposes a workflow for geological domain modeling suited for stratigraphic deposits. The workflow consists in automatically defining the domains by using clustering algorithms, generating the surfaces that represent the contacts by interpolation and subsequent triangulation, and simulating the surfaces. The proposed workflow produces consistent and realistic results and allows the user to test different domain configurations and assess volumetric uncertainty automatically and quickly.

Jun 25, 2023

By Charles Bruce

Although much has been said about the high cost of exploration, both at home and overseas, little of a specific nature has been published on actual finding costs, if indeed such data has been developed. This contrasts sharply with our sister industry, petroleum, where finding costs for oil and gas are available for virtually any country In the world. The reason is largely attributable to the genetic complexity of the hard minerals, as opposed to petroleum, and the increasing difficulties we are facing in the search for new orebodies. We have available to us data on the annual exploration budgets of most of the major mining companies which show them to run into the tens of millions of dollars. My co-panelist, Dr. Walthier, Director - Corporation Exploration, St. Joe Minerals Corporation, New York, NY, summed up the feelings of many explorationists in a recent keynote address when he stated, "I would not recommend a mineral exploration program of a general nature in North America budgeted at less than three to four million dollars annually, spread over four to five years -- or smaller amounts for more years". We have the fact that many of the major companies now prefer to "buy into" a new mineral discovery, particularly overseas, because of the high-risk and high-cost of exploration. Is there, then, a place for the small investor, let us say with a budget of under $200,000 per year and, if so, where and how? This paper is directed toward the above question and is based on experience gained while managing a limited international exploration program, on a shoestring, over the past three years.

Jan 1, 1976

By Víctor Vázquez, Guillermo Tiburcio, Martin Encinas, Jesús L. Valenzuela, Erick Montaño, Alejandro Valenzuela, José Parga

Merrill-Crowe is the primary process used for the concentration and purification of silver in a cyanide solution. The Langmuir Adsorption model for silver recovery in a cyanide solution was used for the study. The maximum adsorption capacity was 6.19 mmol/g for silver. This model properly adjusts the experimental results of the adsorption equilibrium with high correlation coefficients, which also favors the formation of a single layer of molecules adsorbed for the silver in the electrocoagulation- generated species. The thermodynamic parameters ΔG, ΔH, and ΔS were estimated, and it was found that the adsorption process is exothermic and spontaneous. For the kinetic study, the Lagergren second-order equation was used to study the adsorption speed. To characterize the solids coming from the electrocoagulation, X-ray diffraction (XRD), and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) were used; the results of this study suggest that silver is present in aluminite, hydroniumjarosite, and alunogen.

Oct 30, 2021

By L. F. Nicolai, W. J. Schlitt

Lateral migration of leach solution in heaps and dumps is attributed to two phenomena. One is site-specific anisotropic conditions that exist on a macroscopic scale on the surface or within the rock piles. The second is associated with a random walk phenomenon that causes dispersion of solution, especially at gradients in flow or hydrostatic pressure. The latter phenomenon is a general condition that will occur in any leaching operation. Its effects are modeled by computer analysis and are compared with available field data on heap leaching. Under appropriate assumptions, the observed 58° angle of solution dispersion can be reproduced by the model. The combined effects of both anisotropy and random walk are also discussed. Finally, the impact of lateral solution flow on actual leaching operations is considered.

Jan 1, 1988

By Euler De Souza, Jason Chew, Aldrich Philip Dirige

Sillmats are structural elements upon which the safety and economics of underfill mining or sill pillar recovery in stopes of moderate width with steeply dipping ore zones, depend. The traditional stability design of cemented sillmats appears to have developed from experience and from standard static physical model tests such as uniaxial and triaxial compression. Such standard static physical model testing approach arrives at some approximate parameters, normally used to describe or predict the behaviour of sillmats in analytical or numerical models. This approach offers inherent limitations and generally results in conservative designs. Centrifuge modeling studies are combined with numerical modeling in this paper to provide insights into sillmat strength behaviour. The results of both modeling techniques suggest that, in stopes with smooth rock wall conditions, sillmat failure is driven by the fill self-weight and has minimum dependency on the fill binder content. In stopes with rough rock wall conditions, however, the wall roughness contributes significantly to the stability of the sillmat during underfill mining. This study indicates that the stability of paste fill sillmats can be designed with confidence using centrifuge physical modeling in combination with numerical modeling.

Jan 1, 2001

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By C. D. Mann

INTRODUCTION The sublevel stoping mining method is usually applied to a relatively steeply dipping, competent ore body, surrounded by competent wall rock. Ore is produced by drilling and blasting longholes, which can range from 50 mm (2 in.) to 200 mm (7% in.) diam, with lengths up to 90 m (300 ft). Longholes can be inclined in any direction, but the ring or pattern usually forms a plane, and the holes are blasted as a unit. Recently developed mobile drilling and loading machinery, as well as new explosives products, blasting techniques, and cemented sand and rock fill have made sublevel stoping a highly efficient and versatile mining method. When designing a sublevel stoping production sys- tem, it should be kept in mind that production rates from conventional sublevel stopes vary widely through- out the life of the stope. Early production is at a low rate, coming only from the drawpoints near the slot, but increases as new drawpoints are reached by the stope face. As the stope nears completion, again, fewer drawpoints are productive. Enough drawpoints must be available at any time to provide required production. Drawpoint availability should be compared to equipment availability; plan for more drawpoints than are needed at any one time. Accurate, realistic scheduling is essential to smooth production rates. Also, initial recovery of ore in a stope/pillar block is normally from 35% to 50% in sublevel stoping. Planning of pillar recovery, representing the majority of ore tonnage in a production block, must be done during early mine planning. Since much of the development already done for primary stoping (access for drilling, drawpoints, and haulageways), can be used for pillar recovery, early production from pillars is highly desirable. The following description of components of the system is an attempt to highlight some of the most important features and requirements of mechanized sublevel stoping methods. Similar comments would apply to the use of older equipment (column-and-arm drill setups, slushers, etc.) in similar methods. As in any good mining system, maximum economic recovery of the resource in the ground is the primary consideration. STOPE DESIGN CHARACTERISTICS Length and Width The following are some of the factors which affect sublevel open stope length and width dimensions: ore body geometry, principal stress directions, competence of stope back, optimum drill pattern, and drilling drift layout. In new mines initial stope layout design may occur before the ore body is actually intersected by mine workings. Stope dimensioning is a critical decision, and assistance from as many knowledgeable people as possible at this stage is essential. Operators with past experience in similar ore bodies, rock mechanics experts, and others with mine design experience should participate at this stage of stope planning. Height The following are some of the factors which must be considered in determining stope height: competence of stope pillar and stope/fill walls; slenderness ratio of adjacent pillars; ore body dip; ore body thickness; hole depth capability of the drilling machine; fragmentation characteristics of the ore; and level intervals in existing mines. In competent ground, drill-hole length and accuracy are the most important determinants of stoping height. Frequently entire drilling sublevels can be eliminated because of the depth capability of sophisticated drilling equipment, resulting in significant development cost savings. Drawpoint Location and Design Some of the most important considerations of a good drawpoint system are optimum spacing of draw- points, within the constraints of stope dimensions, for uniform drawdown and maximum recovery; excavations designed for stability for the life of the ore block to be drawn-primary stope ore as well as subsequent pillar ore; floor or roadway design including type of surface, reinforcing, grade for water runoff; orientation with respect to the main haulageway, for optimum loader maneuverability and ground stability at the inter- section; and length, to allow articulated front-end loaders to work in a straight configuration. Careful drawpoint design and construction are keys to successful production. Extra care in development, such as smooth wall blasting, rockbolts or grouted rebar, wire mesh, and shotcrete usually will ensure long draw- point life. Human exposure during production loading is of longer duration than during development or production drilling, and consequently preparation of draw- points is easily justified, particularly when pillar ore can be drawn through the same drawpoints. Secondary blasting of boulders can weaken drawpoints, also justifying good ground control techniques. A smooth draw- point floor of poured, reinforced concrete, on a grade of +3% or +4% toward the ore pile facilitates water flow out of the drawpoint, and ease of loader bucket penetration into the muck pile. Slot Raising, Slotting A slot or other space for rock expansion is necessary in conventional sublevel stoping where vertical rings or rows of holes are blasted. The slot can be started at a slot raise driven by conventional raising methods, raise boring, drop raising (predrilling and blasting a raise from the top, using small diameter-less than 200-mm (7%-in.)-holes for relief), or crater blasting (similar to drop raising, but without relief holes). The slot usually extends from the extraction level to the back of the stope. It is normally expanded to full stope width by

Jan 1, 1982

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By Gerald G. Griswold, Allan G. Provost

"To Sink or Not to Sink"; this play on the Bard's words sums up the considerations and problems that face the owner on every potential shaft sinking project. The growing demand for access into the earth is pressing construction into new areas and to greater depths. The following discussion will entertain some of the effects of these new and unknown aspects upon the approach to designing and sinking of deep shafts. We will also look at the current shortages of equipment, materials and skilled manpower, and their effect upon the planning and sinking of shafts. Particular emphasis will be placed upon equipment selection, and we will discuss how economics, while always a prime consideration, is now, more than ever, both an incentive and a detriment to the industry. FUTURE CONSIDERATIONS Shaft construction is assuming ever increasing importance both in mining and civil endeavors. The rapid depletion of near surface mineral reserves is requiring the mining industry to look deeper into the earth for new sources. These greater depths increase the exposure to unfavorable geological conditions; heavier ground, high water pressures, and high temperature. South African gold mines have now reached depths of 12, 000 feet, where the rock temperature is 1380 and water bursts from the fissures. In North America depths to 7, 500 feet have been sunk, but deep shafts are still generally considered to be those of

Jan 1, 1974