Search Documents

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By I. R. Miller

The purpose of this discussion is to try to offer some suggestions as to how the zinc and lead markets will perform over the balance of the decade, review some of the factors influencing production and come to some conclusions regarding prices. The past 2 years have been simply awful in terms of consumption, prices and overall profitability for the industry. In looking ahead to the year 2,000, it is probably not a bad idea to look back about 20 years to see where we have been and how we got to where we are. Zinc consumption from 1950 to the early 1970's increased steadily and rather nicely at an annual average rate of close to 4.0%. It was starting in the early 1970's that things started to get volatile and at times, difficult for the industry. The general economic boom of the early 70's was marked by annual consumption rates close to 5.0 million tons, a level not seen again for over 10 years. The First Oil shock of 1973-74 was followed by the sharpest consumption drop in memory. In two years, Western World zinc consumption fell 27%. While our chart shows a rather dramatic recovery thereafter, the average annual growth rate since 1970 has only been a rather modest 1.5%.

Jan 1, 1992

By Robert J. Timko

New methods of reducing stopping leakage have been investigated by Mine Safety Appliance Research Corporation, working under contract to the U. S. Bureau of Mines. It was found that proper construction techniques are far more important in reducing leakage than the type of sealant used, provided the sealant has sufficient adhesion and strength. Leakage could also be substantially reduced by brushing on modified mortar sealants rather than using the accepted method of trowelling them on.

Jan 1, 1982

By G. Wang

Industrial minerals processing has gained importance lately, not only due to its wide range of new and regular applications in processing different industrial minerals, but also due to the strict specs under which products are commercialized. Among the processes applied to industrial minerals, flotation is a leading technology. The laboratory study and commercial operation demonstrate that the sulfonated reagents are very effective collectors for industrial minerals. This paper compares synthetic petroleum sulfonate with fatty acid on iron reduction in glass sand processing and describes the effect of conditioning pH on iron reduction using synthetic petroleum sulfonate as collector, the effect of molecular weight of natural and synthetic petroleum sulfonates on their flotation performance and the enhancement made for certain products.

Jan 1, 2011

By Kevork Chouzadjian, Gary Davis, Nicholas Katsikaros, Bruce Kelley, Mellie Mavatoi

A process has been developed to recover gold and copper from two waste materials at the Bougainville Copper Limited mine in Papua New Guinea. It involves the bioleaching, in reactors, of a pyrite concentrate to liberate refractory gold and generate sulphuric acid, ferric sulphate and biomass for bacterial leaching of a chalcopyritic waste rock dump. Gold is to be recovered by cyanide leaching and copper by solvent extraction/electrowinning. The reactor bioleaching was developed in continuously operated reactors of 1 m3 capacity by CRA Advanced Technical Development at Cockle Creek, while the dump leaching was developed in 750 kg columns on site at Bougainville Copper Limited. The process was to be piloted on site.

Jan 1, 1990

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By H. Sevim

A new method of designing haulage systems, consisting of belt conveyors and hoists for underground mines is discussed in this paper. Efficient and economic design of such systems will prevent operational bottlenecks and provide savings. The developed model uses a heuristic algorithm to optimize the design parameters and to select the proper equipment specifications. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate belt conveyor networks of any configuration and hoisting systems that can be either drum or friction hoists for single or multiple-level operations. The model also has the option to internally determine the required capacities of the bunker(s) and shaft- bottom bin. The objective of the optimization process is to minimize the "expected cost per ton of ore hauled" from the working faces to the surface. A numerical example is included to illustrate the capabilities of the model.

Jan 1, 1987

By Robert W. Miller, Rhoda S. Kriesel

INTRODUCTION With each passing year, the general public becomes increasingly aware of the potential hazards associated with many products and services previously considered unharmful. This new consciousness is especially evident in the workplace, both as the result of advances in scientific understanding and the influx of concerned, responsible professionals into the labor movement. For example, data produced by epidemiologists doing retrospective mortality studies which related mortality to toxic substance exposures has often been the prime motivating factor behind reductions in exposure standards. This certainly has been the historical case with many radiation exposure standards, including the limitations set for "Working Level" exposure. The concept of "Working Level" was introduced in PHS Publication No. 494 as a result of both the difficulty in relating radiation units to biological effects and the complexity of interaction of radon daughters with the physical environment. WORKING LEVEL One working level is defined as any combination of radon daughters in one liter of air that will alternately release 1.7 x 105 MEV of alpha energy during decay of 210pb (RaD). Its usefulness is that working level can be readily measured in both the field and the laboratory. Because of this, existing occupational exposure standards for radon daughters in both the U. S. and other countries use working level as their basis. In the U. S., the last twenty years has witnessed a significant reduction in radiation exposure standards from 120 working level months to 4 working level months per year. New international standards are being proposed that would be only slightly higher than these current U. S. standards. POTENTIAL EXPOSURES TO RADON DAUGHTERS The universal use of nuclear power, along with the transfer of nuclear technology to developing nations, has significantly increased the demand for fuels. As a result, uranium mining operations have expanded and increased numbers of miners are regularly exposed to radon daughters. In addition to potential exposures in uranium mines, other deep mines such as tin, gold, platinum and tungsten, also have potential exposures due to the distribution of uranium and its accompanying radium throughout much of the earth's crust. The energy crisis has also prompted interest in general population exposure to radon daughters in buildings. Many homeowners, using additional insulation and caulking to seal cracks and conserve energy, have reduced indoor ventilation to the point where working level exposure could become significant, especially in homes with unventilated crawl spaces. In fact, several serious exposure situations have occurred where mine tailings were used for building materials. MEASUREMENT TECHNIQUES Historically, rapid and convenient measurement techniques have been actively sought to improve the ability of ventilation engineers to limit mining exposures through ventilation control. A number of measurement techniques have been developed, including the Kusnetz method (further elaborated by Shalaynev) and techniques developed by Rolle and Tsivoglou. All, however, suffer from similar handicaps that prevent their usefulness in the mining environment. Their main limitation, in terms of minimizing employee exposure, is the elapsed time from the start of sampling until the results can be calculated. It is usually 40 to 90 minutes. This time delay presents both serious economic limitations as well as the potential for exposing workers to high radon daughter concentrations until calculations are completed and corrections made. Further reducing the utility of the Kusnetz and Tsivoglou techniques is the need for tedious calculations that increase the possibility of human error along with the need for cumbersome sampling equipment that is not ideally suited to the mining environment. INSTANT WORKING LEVEL METER To alleviate these problems, the idea of an Instant Working Level Meter was conceived by several groups. Several such instruments were proposed, built, and tested with disappointing results. Although the concepts behind them were sound, the instruments simply failed to measure working level without excessive distortion. In addition, their cost was relatively high, gamma background presented a problem, and sophisticated computations were necessary to determine working level. In short, these systems lacked the design engineering that would make them suitable for the demands of a mining environment.

Jan 1, 1981

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the 'T' bracing principle. Previously, Jarva's line of tunnel boring machines, even their smallest, was designed on the 'X' or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the 'T' scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

By R. D. Rein

The Henderson mine is a large continuous panel caving operation in central Colorado. The orebody is roughly 760 m by 910 m and will be extracted from two production levels. Each level is divided into three north - south panels 244 m to 317 m wide. The general arrangement of a production level and its associated undercut drifts is shown in Figure 1. The production drifts (3.6 m by 3.7 m) are spaced 24 m apart center to center and have undercut drifts (3.4 m by 3.8 m) 17 m directly above them. The production drifts are interconnected with drawpoint crosscuts (4 m by 4.3 m) driven on 12 m centers. Drawpoint crosscuts receive substantial brow steel and concrete support prior to undercutting. The brow steel is a 15 cm by 46 cm wide flange beam with a 2.5 cm wear plate to box in the 'cave' side of the beam. The concrete is a minimum of 0.3 m thick and the batch design results in 27 500 kPa strength. The finished drawpoint opening is 3.7 m by 3.2 m with a choke area of 3.7 m by 2.4 m. (Figure la) Undercutting and bell formation is accomplished by blasting rings of 7.6 cm holes drilled from the undercut drifts. The rings have a burden of 2.0 m and six rings develop one complete bell.

Jan 1, 1985

By Larry Lynott

This paper summarizes the benefits ofusing an in-situ analyzer in a sampling and valuation program. The tests and studies cited quantify the problems associated with current conventional sampling techniques and contrast conventionally-obtained results with those obtained through in-situ analysis. Data are presented to show the improved precision in valuation resulting from the in-situ method. Greater precision in estimating the mineral content of unmined ground becomes increasingly important as mines strive for optimum exploitation of their deposits. As the following analysis shows, the variable distribution of minerals within a deposit, along with the difficulty and the cost of high density sampling limits the precision which is currently possible in practice. An inherent problem exists in the conventional method of sampling. The erratic values of ore grade necessitate the collection oflarge numbers of samples for statistically accurate valuation and ore reserve estimation. Owing to the cost of manpower, current sampling techniques do not allow for the collection of sufficiently large numbers of samples. The most common method of sampFng in current practice is chip sampling, although bulk sampling is sometimes used. The intent of sampling is to obtain an estimate of the value of blocks of ground prior to mining. This information is used to plan the rate and sequence of mining, yet the sampling intervals which are possible in practice cause these block estimations to be ubject to considerable uncertainty. This inevitably leads to mcorrect mining decisions which may be vy costly.

Jan 1, 1998

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By Gunder Homstvedt

The paper presents a new method for boring of blind inclined shafts. The machine, called BorPak, developed by The Robbins Company, operates similar to a mini TBM. It is a remote operated, self propelled drilling machine mounted on a crawler for high mobility and launched out of a starting tube for quick collaring. A short history of the operation of the prototype in Scandinavia and Canada is included in the paper. The BorPak is capable of boring raises at angles from 30° to 900 from horizontal in sizes ranging from 1.2m-2m diameter without the use of drill pipe. The BorPak represents an innovative tool for improved performance, reduced costs and creating a safer working environment.

Jan 1, 1993

By R. W. Barbaro

The limitation of sulfur dioxide in power plant emissions dictates that sulfur in coal be reduced to the lowest possible level before combustion so as not to aggravate the emission control problem at the stack. For coal fired power plants, the methods in practice to achieve low sulfur coal include mining areas with relatively low sulfur. reducing sulfur in the mined coal through preparation techniques and blending high and low sulfur coals. A prerequisite to the successful implementation of any of these practices is the knowledge of the spatial distribution and the capability to predict sulfur values in a coal seam.

Jan 1, 1988

By John D. Morgan

The United States is the world's most productive nation and its citizens enjoy one of the highest material standards of living of any people in the world. Materials and energy are the lifeblood of any industrialized economy. Annually the United States uses over 4 billion tons of mineral materials and fuels, or 40,000 pounds per person as detailed in Figure 1. Domestic processed materials of mineral origin and energy are valued at more than $150 billion annually, and they are derived largely from domestic sources, supplemented by imports, as detailed in Figure 2. In recent years the superior productivity of the United States has also enabled it to give food and manufactured articles to many other less fortunate nations and peoples of the earth. What then is our concern with materials at this time? Seeing the burgeoning increases in our mineral demand: from 2 billion tons in 1950, to over 4 billion tons today, and projected to 11 billion tons by 2000 - we are getting questions concerning our ability to continue to increase production sufficiently for the future.

Jan 1, 1974

By Robert C. Schenk

The rapidly expanding, globally based mining industry provides many opportunities and challenges for the engineering construction business. This paper reviews some of the innovations that the industry is implementing to provide increased value in the design, construction, and successful start-up of new mine plant facilities. Approaches being taken to reduce installed-plant costs as well as related value-enhancement opportunities are discussed. Included are comments on new technology developments, use of automation and global communications networks, application of economic models as a project design tool, and management approaches being adopted to make the engineering construction process significantly more effective.

Jan 1, 1998

By T. W. Conrad, B. Kerr

During the last decade grassroots minerals education programs have blossomed throughout the United States and in other countries. At the same time an environmental education movement has been gaining momentum. While this offers a unique opportunity to share the mining industry’s story, it also has some potential pitfalls. In this paper the authors will discuss some of the benefits of participating in environmental education and provide some practical tips for success, based on New Mexico experiences. It will conclude with a presentation on a successful environmental education program at Heights Middle School in Farmington New Mexico.

Jan 1, 2001

By K. -A. Björkstedt

INTRODUCTION Strassa lies in the central part of Bergslagen, a tradi¬tional mining district, on the eastern side of the Stora Valley at an elevation of about 200 m above sea level. A railway siding runs between the mine and the Stora railway station from which there are railway connections to the shipping port and iron and steel works in Oxelosund, about 224 km away. The distance to the provin¬cial capital Orebro is about 60 km. The climate is typi¬cal for this part of central Sweden and is illustrated by the diagram of monthly precipitation and temperatures for the years 1968-1975 (Fig. 1). HISTORY There is no certain information as to when the Strassa mine was first worked, but it is known from sur¬viving accounts of mine inspectors that there were smelt¬ing works in operation in nearby villages in the 12th century. An example is the Gusselhytta ore smelting works, 10 km south of Strassa, which dates from this period. Around the year 1540 there were two smelting works in Strassa, the Upper Karberg and Lower Karberg works. Ore for these smelters was probably taken from Strassa and from the adjacent Blanka mine. In the year 1624 Strassa is mentioned by the painter Jons Nils Krook in an account of the iron mines in the Linde mining district (Linde Bergslags Jarngruvor). Several mines were listed in the area, the deepest being about 30 m. An impressive power installation is mentioned in 1639, including a piston system of lashed poles for transmit¬ting power from the Stora River to the Strassa fields. Its length was 2670 m. Common ground comprising about 20.2 km2 (5000 acres) of forest was allocated in 1689 for the furtherance of mining operations. Until the beginning of this century only the rich cen¬tral parts of the ore body were mined and these yielded, after handpicking, lump ore suitable for smelter feed. An example of the ore grades from these early times is an analysis of ore from the "Big Mine" (Storgruvan) from the year 1873: 48.5% Fe, 0.008% P, and 0.06% S. This same year a total of about 18 000 t was ex¬tracted from the Strassa mine. OWNERSHIP The mine was owned and run until 1874 by a min¬ing association made up of 119 so-called "bergsman," who were homesteaders often engaged in agriculture and timber-cutting as well. In that year the Strossa Grufvebolag (Mining Co.) was founded. In 1906 it was con¬verted into a joint stock company, the Strossa Gruveaktiebolag. This was acquired in 1907 by Metallurgiska AB for the implementation of Gustav Grondal's beneficiating and briquetting methods, for which the Strassa ore was well suited. The same year saw the completion of a new ore dressing plant with an annual production of 46 000 t of ore concentrate. In 1911 the mine passed to new hands, and in 1913 it was purchased by an Austrian company. Extensive new installations were made and in 1915 a new dressing and briquetting plant was completed with twice the capacity of the old one. In 1917 the Strassa mine was acquired by Granges. Be¬cause of unfavorable business trends and technical diffi¬culties, mining operations were brought to a close in 1923. Pumping kept the mine free of water until 1933 but it was completely filled ten years later. Up to 1950 the surface buildings and installations remained intact but the large dressing and briquetting plant burned to the ground in that year. Today only the machine shop re¬mains from this earlier period of operation, now housing parts of the Mineral Processing Laboratory. The decision to take up mining operations again was made in 1955 and construction work began the follow¬ing year. Of the old installation, only the "southern shaft" could be used for some development drifting after it had been completed with a new headframe. Other¬wise, all the buildings and installations required for the operations had to be rebuilt. New installations ready by 1960 were office and personnel facilities, a new shaft and headframe, a sorting and concentrating plant, a macadam plant, settling basins, pump stations, and a railway and yard with transport equipment. The instal¬lation was completed with two plants

Jan 1, 1982

By Thomas D. Barkand

Investigation of several serious hoisting accidents identified machine brake failure as the most common cause. The recent revelation of this potential hazard has prompted regulatory authorities to require an additional, independent, emergency braking system. As a result of this initiative, a new generation of braking systems have been developed and applied to mine elevators. This paper will discuss the design and testing of an electrical dynamic brake, pneumatic rope brake, and traction sheave brake. The effect of compound braking on hoisting systems equipped with multiple brakes will also be addressed.

Jan 1, 1992

By C. V. Deutsch, J. B. Boisvert, M. A. Cuba

The amount of information available for characterizing a deposit increases over time due to the continuous acquisition of data during mining. This additional information is collected from different sources, including geologic mapping, production data and infill drilling. Throughout the lifetime of a mining project, the block model and the mining sequence are periodically updated to account for this new data. In general, the acquisition of additional data increases the accuracy of the block model, reduces uncertainty in ore/waste limits and clarifies the optimal mining sequence. There has been extensive research on mine planning, but current techniques do not consider the decrease in uncertainty as additional information becomes available. Conventional paradigms assume either 1) the kriged model is correct and uncertainty due to multiple realizations does not change the mining sequence, or 2) the mining sequence is unrealistically adapted to each realization. A new paradigm is proposed for evaluating minable reserves of surface mining projects, which accounts for the acquisition of additional information in the design of the long term mine plan. Multiple scenarios characterizing the dynamic nature of mining and data collection are created. In the proposed methodology, the performance of the long-term mine plan depends on both mining and data acquisition strategies. Each scenario considers the same extracted volume for the first period, resulting in a set of scenarios that diverge from a common initial period, accounting for how the mine may develop over time as new data are acquired and provide a more realistic evaluation of reserves with an appropriate level of uncertainty. A synthetic example is presented to illustrate the implementation of the methodology and the benefits over conventional paradigms.

Jan 1, 2013