Search Documents

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

By Jim Morris

This paper will describe the excavation of a 5.4 percent decline at the Montanore Project for Noranda Minerals Corporation. The 5.3 m by 4.9 m tunnel was driven to provide access for the exploration of a major copper-silver deposit. Soft ground and conventional drill-blast mining were used on the 4,270 m tunnel. Ground support consisted of steel sets and concrete in the soft ground and pattern rockbolts providing the majority of the rock support. A special feature of the project was the use of conveyor haulage in conjunction with the drill-blast excavation.

Jan 1, 1993

By P. Bevilacqua, M. C. Williams, T. P. Meloy

We will bet you that, without prior programming within 10 minutes, we can design and simulate a 10,000 unit operation separation circuit. We will even do it at your place. We do it all the time. [ ] There are no tricks; we do it in a spreadsheet. We do it in those user friendly spreadsheet such as Quattro Pro. Spreadsheets must be user friendly. Accountants use them as do managers, business men, lawyers, doctors and salesmen. What these users seldom realize, is how powerful a mathematical tool a spreadsheet is. Among their other capabilities, spreadsheets can do a finite element analysis. That is why they are useful for accounting. That is also why they are more useful to engineers in the mineral industry. Spreadsheets are ideally suited for the engineering problems in the mineral industry. We have used then for solving problems in: a) mine ventilation; b) circuit design and optimization of dense media, flotation and sizing; c) comminution circuit design; d) shaking tables; e) Humphrey spirals; f) sluice ways and channel flow; g) lock particle and liberation problems; h) tunnel and shaft stress problems; i) cascadograph simulation; j) complex heat transfer problems; k) flow in porous media; and sheet flotation (Figure 1). Mineral industry problems presented on or with a spreadsheet are an excellent teaching instrument, problem statement and solution tools and sales devices. Spreadsheets answer easily, quickly and reliably many mineral industry engineering problems. What makes spreadsheets so useful to the mineral industry. The short answer is: they are easy to use; mineral industry problems fit the spreadsheet format. Those reasons are part of the answer. The real answer lies with the structure of the spreadsheet itself. Essentially, a spreadsheet is a "finite element analysis" form of computer software. Many mineral industry problems are readily solved by finite element analysis techniques. While some in the mineral industry may think they have never heard of finite element analysis, most use it weekly if not daily. Any profit and loss statement is essentially a finite element instrument. In fact, any array of numbers where one number is related to another may be construed as a finite element analysis product. Finite element analysis is a common daily activity. To get an appreciation of a finite element analysis, think of a monthly sales forecast for the next year. For each product and for each month, there exists a dollar figure for the forecasted amount of sales. In the forecast statement, for a given product in a given month, there is a "box" where the forecasted figure is presented. The forecast figure in that box was arrived at through some type of formula. The formula probably required some information from other neighboring boxes in the master forecast statement. Voila, one has a finite element analysis. Today the analysis would be done in a spreadsheet. A typical mineral industry problem is ventilation in an underground mine. Think of a rectangular room and pillar mining operation. Each room has air entering at a given pressure and velocity and air leaving at another pressure and velocity. During steady state, the air entering and leaving the room is determined by conditions in the adjacent rooms. One can readily model the room and pillar mine layout in a spreadsheet, and then find the flow in and out of each room at steady state. Change the flow by moving a brattice cloth or blocking off a path way and one gets a new air flow profile. Change the numbers on the spreadsheet that reflect

Jan 1, 1993

By Maurice C. Fuerstenau

INTRODUCTION The term, chelate, from the Greek for 'claw,' has its origin in the pincer-like representation of more than one atom of a single ligand bonded to the same metal atom, forming a ring-like structure. Depending on how many attachments exist on the sphere of coordination around the metal ion, ligands are referred to as bidentate, tridentate, tetradentate, pentadentate and hexadentate According to Calvin and Martell (1952) and Somasundaran and Nagaraj (1984), chelating agents must contain suitable functional groups, and their location within the ligand molecule must enable ring formation that is sterically possible. Typical structures that meet these requirements have been given by Fuerstenau and Herrera-Urbina (1988) and are listed in Figure 1. As noted, the functional groups of these reagents contain electron donor atoms such as oxygen, nitrogen and sulfur. Basic groups, such as amino (-NH,), are those that contain an atom with a lone pair of electrons. Acid groups are those, such as carboxylic (-COOH) which lose a hydrogen ion and coordinate with the metal atom. Examples of each of these types chelating reagents are given in Tables 1-4. The specificity of chelating agents for various metal ions has long been known and was utilized early in the search for new flotation collectors. In 1927, Vivian used ammonium nitrosophenylhydroxylamine as a collector for cassiterite. Holman (1929) tested dimethylglyoxime as a collector for nickel oxide. He also suggested taurin as a collector for oxidized lead ores. DeWitt and von Batchelder (1939) suggested the use of oximes as flotation collectors. Gutzeit (1946) conducted an extensive investigation on the use of chelating agents as collectors and as depressants for gangue minerals. The depressants are those reagents that form soluble chelates with metal ions that could function as

Jan 1, 2005

By Howard M. Wells

Investment in minerals development usually entails big financial outlays. which will remain at risk for a long time before the venture can begin to generate a return cash flow. Before 'committing himself to such a venture the investor would be wise to carefully examine the possible consequences of his exposure to risk. In this context risk is defined in multiple terms, which relate the magnitude of possible loss with the probability that such loss may occur--normally the probability will decrease as the amount of possible loss increases. The analysis of risk is an essential component of the decision making process, especially so in the case of low grade high tonnage mining ventures where a very real possibility exists that future unfavorable circumstances may lead to losses that could cripple or ruin even the richest corporation. Wells (1979) postulates a rationale for making the investment decision under uncertainty based on the comparison of two independent risk criteria: 1) the risk inherent in the venture represented by the negative portion of the cumulative distribution of the net present value (NPV), as derived by a stochastic evaluation procedure, 2) the limits of risk the decision maker is willing to accept, taking account of the financial capacity-of the 'firm to absorb various levels of future cash shortfall should the venture prove disappointing. The chance the investor would be prepared to accept can be expected to decrease as the amount of the possible shortfall increases. The limits of acceptable risk are-defined by a curve called the "LL-curve" which can be directly compared with the cumu¬lative NPV curve. A positive investment decision is implied if the limits of acceptable risk are not exceeded.

Jan 1, 1982

By J. B. Gwiazda

Maintenance of a constant load setting throughout longwall support units and selection of the proper initial bearing capacity depending on the type of roof strata are the basic factors that ensure good performance of roof support in a longwall. These requirements can only be met by hydraulic support. The greatest advantage of hydraulic support is achieved when uniform pressure is imposed on the roof throughout the length of the longwall. Such support, however, is provided only if each of the support units acts with the same force against the roof, i.e., has the same setting load. In such cases, the roof behaves like a uniform plate without bending and shearing stresses, thereby ensuring an undisturbed structure. Without a positive set value system, achieving an equal setting load for all units of the longwall support is impossible. Due to alterations of the feed line pressure of support units as well as some reasons related to man's psychology, operators extend the height at different setting loads. This produces nonuniform roof stress, and disturbs the structure. Consequently, the roof usually cracks. The author has developed a positive set value system, which is described in this Technical Note. Selection of the setting load Two pressure values in the feed lines are usually applied in longwall hydraulic systems. Lightweight support is fed by 25 MPa (250 bar) liquid, while heavy duty units receive a nominal pressure of 31.5 MPa (315 bar). Such pressure is required not only for the props but also to power the adjust¬ment jacks and the advancing ram. If the feed pressure is too low, there will be difficulty in shifting the unit despite the inversion system of the advancing rams. On the other hand, for many roof types, the feed pressure often appears to be too high when applied as the setting load pressure. An excessive setting load acts too strongly against the roof, crushing weak strata close to the roof. The author has recognized a case where an excessive setting load destroyed not only the nearby roof strata but also the strata above a 2-m (6.6-ft) sandstone layer. In addition, an excessive setting load relieves the side¬walls, increasing the resistance when using cutting machines. As a result, the yield of coarse coal is diminished, and increased fines dominate in the final product, lowering its economic value. As indicated, selection of the proper setting load, depend¬ing on the mining and geological conditions of the extracted seam, is extremely important. In some mines, measures applied to prevent disturbances include reduction of the feed line pressure by adjusting the feed pump valve. The disadvantage accompanying reduced feed line pressure is more difficult operation in advancing the ram. Due to the reduced feed line pressure, the force of the advancing ram is much lower than the designed value. Other designs suggest using a third feed line. However, installation of supplementary valves on the support units is required, a time-consuming and expensive procedure. The disadvantages of the powered supports are eliminated by a system designed by the author. So far, such a method of setting load control has not been used in any type of support. Setting load control unit The designed positive valve set for prop loading and the setting load control correspond to existing control systems for hydraulic powered support. The layout of the unit connected to the hydraulic prop control is presented in Fig. 1. The unit is marked LIDS. It incorporates three valves that may operate separately or connected. Valve A automatically opens and closes with liquid flow in the prop feed circuit. The valve is opened when the canopy touches the roof and closed when the support unit is withdrawn. Valve B serves as the setting load control. Valve C automatically opens and closes the flow in the line connecting the under-piston space of E to the prop F with the separator G. The valve block of each support prop is marked BZ. The UDS unit is connected by the hydraulic lines to the F prop control circuit. A valve is connected by H to pressure line J and by K to the G separator. In the UDS-3 version, line L is connected to M, linking the over-piston space of F prop with the G separator. Valve B is linked with valve A by a connector; it is also connected to the under-piston space E of prop F by line P. Valve C is fixed between lines K and P, connecting space E of prop F with the separator G. When setting the support, the liquid flows from line J through separator G, the BZ valve, and valve C to the space E of prop F. When reaching the roof with the canopy, valve A is opened and C closes. In this way it is impossible for the operator to cause the liquid pressure in space E of prop F to reach the level of line J. The prop pressure is set by valve B of the UDS unit. When withdrawing the support, valve C is automatically opened and A closed. Three UDS units have been fabricated and are designated

Jan 1, 1990

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the micro- computer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user pro- grams to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to en- courage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Har- mon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the com- puterized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage ) , the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 1, 1988

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By Kevin Schraden, Andrea Pezzi

environmental and social/political changes the world is currently experiencing. Three of major challenges facing the mining industry today are: water scarcity, unpredictable weather conditions that generate a risk of tailings dam failures as well as the correlating social pressure and government regulations that prevent the development of new or expanded tailings dam projects. It is estimated the total number of active, inactive and closed storage facilities globally is over 8,500 containing over 217 km3 of tailings (46% are from copper mining)1 which at some point will need to be addressed. Technologically, there are several solutions for tailings management, including conventional ponds, thickened tails, paste backfill and filtered dry stack tailings. The use of pressure filters, for tailings dewatering is currently being evaluated and often selected as the preferred technology where dry stacking is the chosen solution for residue disposal. This is mainly due to the pressure filters ability and flexibility to address and achieve the current challenging aspects of tailings processing including: • Extremely high capacities of >80,000 dry tons/day • Lower ore grades which require finer grinding and result in a higher amount fine fractions and clay content • Residual moisture targets required for the geotechnical specifications for dry stacking

Feb 1, 2024

By M. D. Flavel, J. C. Motz, G. V. Jergensen

Introduction Compared to the gyratory crusher, the cone crusher is character¬ized by its higher speed and a flat crushing chamber design which is intended to give a high capacity and reduction ratio for materials suitable to this type of processing. The aim is to retain material longer in the crushing chamber to do more work on material as it is being processed. A concept of how a piece of stone might flow through a secondary crushing chamber is shown in Fig. 45. The number of times material will be nipped during crushing will depend on material size, friability, and the geometry of the crushing chamber as well as its speed and eccentric throw. Cone crushers are usually specified in terms of closed-side setting (CSS) and a given quantity of material passing a particular square-mesh screen size. A criterion of product passing closed-side setting is often available. This value will vary according to the particular crusher design and the details of its applica¬tion. Essentially, cone crushers can be classified into distinct types, depending on their duty. Crusher sizes for all duties are described by terms arising out of common industry usage, such as 3-ft, 7-ft, etc., which refer to the crushing-head (mantle) diameter. At present the range of sizes available varies from approximately 2 to 10 ft diam. Weights vary in the range of 5 to 200 tons, and connected horsepowers range from 10 through 700. There are so many variations that specifics should be obtained from machine manufacturers. The crushing chambers that are fitted to various machines are also often referred to by terms arising out of common usage, such as standard for secondary crushers, and short head for tertiary crush¬ers, which refer specifically to the Symons design. Also used are more specific but equally vague descriptions, such as coarse, intermedi¬ate, and fine chambers. Some manufacturers such as Allis-Chalmers with their Hydrocone crushers refer to the model number of the machine by the feed opening and the diameter of the mantle. For example, a Model 10-84 Hydrocone crusher has an 84-in. diam man¬tle, and is capable of accepting a 10-in. diam sphere at the feed point to the crushing chamber. Rexnord and Telsmith define crushing cavi¬ties in their capacity tables as feed openings at minimum recommended discharge settings (closed-side settings). Each practice offers guidelines which should be carefully defined for the specific crushing problem. The utilization of a cone crusher depends on how well it is controlled and the features of the circuit in which it operates. Normally, it will operate in the range of 75 to 85% of the peak capacity. It is likely that industry pressures will call for a standarized de¬ applied crushing power. Experience has shown that the crushing process is more controllable if certain reduction ratios are adhered to for each stage. Technically, this is defined as that size of feed (in. or mm) of which 80% will pass, divided by the size of the product (in. or mm) which 80% will pass. Secondary Crushers These are the cone crushers which accept suitable feed size material either prepared by a primary crusher or occurring naturally, and reduce it to a size suitable for marketing in one stage, or make feed for subsequent crushing or grinding stages. Secondary crushers have feed openings of 4 to 25 in. in the larger (7-ft) models down to a 2'/a to 4 in. in the smallest 24-in. models. Reduction ratios normally range between 3:1 and seldom more than 5:1. In the 7-ft models, the cone crusher typically makes a product all passing 2 in., but this is dependent on the machine design and properties of the material being treated. Secondary crushers most commonly operate in open circuit. They also are operated in closed circuit with a vibrating screen, depending upon product requirements and conditions where the reduction ratio does not cause excessive power draw and build-up of circulating load. Screening ahead of secondary crushers is generally recommended, especially where the feed contains more than 25% material smaller than the desired closed-side setting. Tertiary Crushers These are cone crushers that normally take secondary crusher product and reduce it to a marketable product or make it suitable for subsequent comminution steps. The reduction achieved is a func¬tion of the crusher design and the properties of the material to be treated. The reduction ratio is normally in the range between 1.5 and 2 to 1, and seldom more than 3 to 1. The tertiary crusher normally operates in closed circuit with a vibrating screen and makes a product smaller than all passing 'h or 5/8 in. Fine Crushers Sometimes these machines are called sand crushers and are called by various manufacturer brand names, such as Gyradisc, Hydrofine, V.F.C., and others. A cross section of a Symons Gyradisc crusher is shown in Fig. 46. Essentially, these crushers would be used in a fourth-stage crushing operation, but could be called on to reduce a screened feed size fraction from a secondary or primary crushing operation. This type of crusher normally receives feed no coarser than 1'h in. that is scalped of all over-sized material and operates in closed circuit with a vibrating screen. For average materials, typical product is '/e in. top size, although a -10 mesh product can be produced on those materials having suitable characteristics. The crusher is nor¬mally operated in a separate circuit from the main crushing plant because of the variations in output rates that are caused by varying physical properties in the feed. The reduction ratio is generally less than 2:1, and circulating loads are generally high. More interparticle crushing takes place in these machines than with conventional cone crushers and capacities can be more sensitive to changes in moisture content, feed size graduation, and other physical properties. Design Features For the various applications, crusher manufacturers normally have a range of crushers of different sizes and power ratings to select from.

Jan 1, 1985

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By Manuel S. Rivera

Abstract. Instrumentation in concentrators has evolved from a few isolated indicators to compu- terized control within twenty years. This evo- lution has caused a drastic change in the phil- osophy, personnel and equipment used in a pro- gram of servicing and utilization of present day automation.

Jan 1, 1980

By William S. Pintz, William A. Vogely, Charles J. Johnson

This chapter on the role of minerals in developing economies is oriented toward economic policy issues. The discussion and analysis cut across the technical, economic, legal, and policy fields. The goal of this chapter is to pro- vide relevant background information important to individuals involved with the minerals sector in developing countries. Where possible, trends are shown to provide a basis for understanding the evolving role of minerals in developing economies. This chapter is divided into the following five sections: (1) characteristics of developing countries (which presents selected statistical comparisons); (2) government objectives in developing countries; (3) government policy formulation in developing countries; (4) determinants of future trends, and (5) a summary of the chapter's major points combined with the authors' view. CHARACTERISTICS OF DEVELOPING COUNTRIES There are 155 nations in the world categorized as "developing countries." In total these nations represent about one third of the value of the world's mineral production, three quarters of the world's population, and over half of the world's land surface area. The group of so-called developing countries is quite diverse and there are exceptions to almost any general observation about the group as a whole. Most definitions of the term "developing country" are based on levels of per capita income. However, if per capita income is the sole criterion used in categorization, then several oil-exporting countries would jump from the category of developing country to the category of developed country.a Obviously, this results in a poor fit with respect to other measures. In general, the majority of developing countries can be characterized by relatively low per capita income, high population growth rates, high levels of unemployment, low levels of education, short average life ex- pectancies, income distribution skewed toward the highest 20% of the population, and a large share of exports represented by primary commodities. b For the purposes of this chapter a slightly modified version of the widely used World Bank system of classification (shown in Table 1.2.1) is used. As summarized in Table 1.2.1, developing countries are divided into three main groups based on estimated gross national product (GNP) per capita. It should be noted that the high- income, oil-exporting countries have characteristics of both developing and industrialized countries; however they are included for most statistical comparisons within the group of developing countries. Of the 155 developing countries in the world, approximately half produce minerals other than common building materials, and only 32 account for more than five percent of world pro-

Jan 1, 1985

By Alfred Jr. Petrick, William A. Vogely

INTRODUCTION The scope of mineral finance extends beyond the economic aspects of property evaluation to all of those activities involving acquisition and utilization of funds with an objective to optimize the value of the firm. It must, therefore, en- compass consideration of the overall financial goals of the firm, decisions involving external versus internal growth and domestic versus foreign investments, management of working cap- ital, efforts to minimize the cost of capital, and decisions with regards to the instruments of long- term debt and equity financing. The scope of this section is limited to considerations of special interest to the mineral or petroleum engineer, which include the following aspects of mineral finance: (1) The technical aspects of mineral or coal property or oil and gas reservoir evaluation which provide the basis for estimation and forecasting of revenues and costs. (2) Estimation and forecasting of costs and prices in a inflationary economic environment. (3) Calculation of cash flows which model .. , the investment in minerals, coal or oil, and gas. Such models require assumptions as to the timing of cash flows, escalation of capital and operating costs, base prices, and escalation, the tax regime, royalties, division of profits and the economic aspects of loans. (4) The role of discount rate in the economic analysis of an investment which requires consideration of the opportunity costs of the firm, cost of capital, risk premiums. (5) Risk analysis including application of the concepts of conditional net present value, expected value, and risk preference as well as the application of the techniques of sensitivity and simulation. (6) Selection of application criteria for in- vestment decision making. (7) Capital structure with particular reference to the effect of debt financing. (8) Consideration of sources of funds utilized by the minerals industries. (9) Long-range planning including portfolio analysis. This section is limited to principles, methodologies, and trends in mineral investment, finance, and long-range planning in the United States with a perspective from the year 1984. Consideration of the key concepts is supplemented by case examples of investment risk analysis and financial structure. Important factors affecting mineral investment evaluation during the 1980s include volatile metals prices, cost inflation, and the introduction of techniques requiring the computer and its capacity for improved technical and economic analysis into the hands of those who know most about the industry. The personal computer is replacing the calculator on the desk of the individual analyst and is rapidly becoming a required tool for the study of engineering and economics. Examples of change brought about by the micro-computer include greatly improved techniques of cost estimation, wider application of the computer for project analysis, computer graphics, reserve estimation, geostatistical analysis, mine design and other techniques that capitalize on the ability of the computer to handle

Jan 1, 1985

By H. J. Marais, P. C. van Aswegen

The Biological Oxidation (BlOX®) Process for the treatment of refractory gold ores was commercialized in 1988. During the last decade, the technology has developed into a mature, commercially viable process, with five additional operations commissioned, including operations at Sao Bento in Brazil, Harbour Lights and Wiluna in Australia, Ashanti in Ghana and Tamboraque in Peru. With ongoing development, the efficiency and cost effectiveness of the process have both improved, making it an attractive alternative to conventional refractory treatment processes such as roasting and pressure oxidation. The bacterial culture is robust and can withstand the normal fluctuations experienced on an operating plant. The plants are simple to operate, making it ideal for remote areas. The scale-up potential of the process has been proven, and it can be applied to large refractory ore bodies. The process is environmentally friendly. Neutralization of plant effluents produces precipitates that comply with the most stringent environmental regulations.

Jan 1, 2000

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003