Search Documents

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By William C. Howe

This paper describes the technical status of the atmospheric pressure fluidized bed combustion (AFBC) process for utility steam generation. Major areas where AFBC development work is needed are discussed. Various approaches to solving these key issues are identified and the ongoing research and development programs addressing the key development areas are described. Other significant programs pertaining to the development of AFBC for utility steam generation are also discussed and needs for future work identified.

Jan 1, 1978

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By Gary E. Slagel

The federal Office of Surface Mining (OSW) has undertaken an effort to revise many of their permanent program regulations. Numerous procedures for compliance are being rewritten to allow for greater flexibility while meeting the requirements of the Surface Mining Control and Reclamation Act. This study investigates, for certain select provisions, the cost differential between complying with the original OSM standards and the more flexible, state-specific standards being allowed in many of the revised regulations. Estimated cost savings that could be realized under a few of the revised regulations are substantial and should provide a basis for seeking revisions to the state regulatory programs.

Jan 1, 1982

By N. Edmonson

Apart from its role as an essential input to a wide array of agricultural chemicals and industrial processes, sulfur is interesting in that its supply involves competition between primary product and by-product. This general production structure is found repeatedly among markets for metals and other industrial minerals, and research results from the sulfur market potentially carry over to other markets with similar structures. The purpose of this paper is to present an analysis of the recent and prospective market for sulfur. The analysis will rely heavily on simulation using a comprehensive model of the North American sulfur market developed by the author. A brief description of the model is offered by way of introduction

Jan 1, 1993

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By Jorgen Elbrond

The calculation of open pit operations&apos; capacities has been the subject of many studies using computer simulations. The common problems of simulation are that if one desires a realistic picture of an operation the programming work becomes long and expensive and that the program requires a large computer and long time to run. The method presented in this paper overcomes these problems by using a straightforward calculation procedure. It is based on the queuing theory&apos;s simple formula for waiting time in a closed circuit and uses a system of correction factors, which reflect the loading, travel, and dumping times&apos; relative variabilities and which have been found by 1) mathematical analysis and 2) simulations of basic circuits. The method includes the main parameters of the operation: numbers, sizes and operational availabilities of trucks, shovels and dumping point, distribution of the production over shovels, trucks&apos; loading, travel (loaded and empty) and dumping times as well as their variabilities, shift&apos;s composition. The procedure models: the average duration of a complete truck cycle during stationary and non-stationary periods during the shift as a function of the number of trucks in the circuit, the composition of the average 100% operated shift, the simultaneous probabilities of operationally available shovels and trucks and the distribution of shovels and trucks according to production and cycle times. The procedure can be programmed for a small computer and requires only short computing time, which makes extensive studies of various parameter combinations practical to carry out. The development of the method is an extension of previous work by Morgan and Peterson {1}, who by simulation established the relation between the match factor (which is the ratio between the sum of one loading time pr truck in the circuit and the complete net cycle time) and the shovel&apos;s efficiency, and by Hayes, Splaine and Whitaker {2}, who established this relation from a large number of observations in the Nchanga pit in Zambia. The present method establishes this relation by a straightforward calculation procedure. Theoretical solutions to some situations are found in the litterature on the queuing theory. The papers {3},{4} and {5} give solutions to situations, which fall outside those encountered in the shovel-trucks circuit. These solutions together with simulations of in-termediary situations have been used to establish an interpolation procedure for the correction factors to be applied to the waiting time formula in order to cover the situations encountered in practice.

Jan 1, 1977

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By I. J. Jansen

Successful soil construction involves preparation of an adequate base, selection of high quality soil materials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experiments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construction. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By Weiguo Xie, MARK LAPUTKA

The pyrometallurgical industry plays a vital role in producing metals for our modern life. With growing demand for metals and declining grade of mineable ore, innovations become critical for many mining companies. This has given rise to the need for a review of recent improvements to the pyrometallurgical industry in terms of analytical measurement techniques, process and equipment improvements, and computer-based modeling/simulations. Because many of these innovations tend to be applied to a wider scope of metals, not restricted to a specific metal, we studied the broad applications of many improvements to a wide range of metals. We found that the challenge of a lack of robust measurement techniques under high-temperature conditions within a furnace hinders optimization of a pyrometallurgical process. Some future opportunities in the pyrometallurgical industry on analytical measurement techniques, computer modeling, and processes and equipment were also outlined and discussed.

By Clifford W. Schultz

Four native copper ores, two conglomerate and two amygdaloidal, were tested to determine their amenability to sorting. One of them, a conglomerate ore from the Kingston mine, showed a high sortability as evidenced by an 80 pct recovery of copper in the minus 6-, plus 1/2-inch size range. Using the Kingston as a case example, the cost of mining and concentrating was estimated for a standard case and five optional cases involving varying degrees of sorting. This analysis indi¬cates that the production cost per pound of copper can be reduced on the order of 1 to 1-1/2 cents per pound along with a significant decrease in capital investment.

Jan 1, 1975

By J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit-optimization stages of a mining project. This paper presents an approach for optimizing final pit limits concurrently over all realizations in a stochastic model and using a risk-management framework to manage the geologic and economic uncertainty. A heuristic pit optimizer is used to find multiple uncertainty-rated pit shells. These uncertainty-rated pit shells follow the mean-variance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk-management framework to further eliminate suboptimal solutions along the efficient frontier. This results in a smaller set of final pit shells that can be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits, and two regions are targeted as potential regions for further exploration.

By D. Hong, K. N. Han

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant was studied. Experiments were carried out in an autoclave to investigate the effects of stirring speed, temperature, solution pH, and iodine and iodide concentrations on the dissolution of rhenium. It was found that a high temperature and a high solution pH were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by the mass transfer of iodine with an apparent activation energy of 15.8 kJ/mole.

Jan 1, 1999

By R. R. Klimpel

In this first report, we present a preliminary model based on the simple binary sys¬tem of component B occluded in a matrix of compo¬nent A, for the case where fracture planes can pass with equal ease through A or B. By assuming that the volume fraction of B in AB in the overall matrix is small, which is realistic for many prac¬tical systems, the problem is reduced to a one-¬dimensional treatment which is conceptually easy to understand. The model was programmed for Monte Carlo simulation, and an analytical solution also developed based on the assumption of zero or one mineral fragment per particle. Preliminary ex¬perimental confirmation using a synthetic "mineral¬-host matrix" of known amount and size of B in AB is presented.

Jan 1, 1983

By Steven J. Schatzel, Kayode M. Ajayi, Marcia M. Harris, Zoheir Khademian

Predicting rockmass permeability is critical in evaluating various engineering designs, including estimating gas inflow to a longwall mine in the case of a hypothetical breach in the gas well. This study conducted field permeability measurements to validate a geomechanical model capable of predicting rockmass permeability during longwall mining. A series of slug permeability tests were conducted in an active mine in Pennsylvania. A model of the mine was constructed in 3DEC numerical modeling software, and permeabilities were calculated. The modeling results agreed well with the pre- and post-mining permeability measurements, showing the applicability of this tool to evaluate gas well stability near mine workings.

Feb 1, 2024

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By G. F. Weaton

1.1 The purpose of this paper is to show the way by which estimates are made of the tonnage and grade of iron ore and taconite reserves of Minnesota. 1.2 The procedures include those of estimating the open pit reserves of: (a) Natural iron ore, and (b) Taconite 1.3 The methods of estimation which will be discussed are primarily based on the information from exploring iron ore deposits. They consider the geology of the deposit as well as the contained mineral of potential value. 2.0 Some geologic, engineering, and economic principles. 2.1 Ore 2.11 "In the broad economic sense, and from a legal standpoint as well, ore is mineralized rock, which under appropriate conditions of time, space, technology, economics, and politics, can be mined, processed, and made to yield a saleable metal , or other mineral products at a profit."(Parks, 1957) Stated differently, metallic ore is rock material from which presently known methods of beneficiation, a merchantable concentrate, suitable for use in the manufacture of metals at a profit, can be produced. Crude ores as low as 0.38% metal, as in the case of copper and even lower in the case of the precious metals.

Jan 1, 1985

By Robert T. Chapman

Many of us are privileged in that we have witnessed the transition from mining methods used in the first quarter of the twentieth&apos; century to those practiced today. In the late Twenties, for example, many mines still used hand mucking methods. In the middle Thirties, more than one large metallurgical limestone quarry still used the 4 cubic yard railway steam shovel formerly in use at the Panama Canal. Mules could occasionally still be found underground, where they provided the-main-source of motive power. Within the last decade, and even within the past five years or less, great improvements have been made in blast-hole drilling, ore loading, and ore hauling equipment. Industrial demand for minerals can be expressed in exponential terms as compared to that at the turn of the century. Even marine mineral resources are receiving accelerated attention. One overall result is that larger and lower grade orebodies can be exploited at a profit. This profit must be made despite, for example, a static monetary price for gold, and despite the continual cost escalation involving labor, materials, supplies, and equipment. Accordingly, the application of the necessary degree of knowledge and judgment required to meet production, cost, and profit goals is paramount.

Jan 1, 1966