Search Documents

By Frank H. Buchella

Principal factors influencing equipment selection can be grouped into five basic categories. Tonnage Requirements, Ore and Waste Loading, transporting, and ground preparation equipment are largely determined by tonnage requirements. Generally, the greater the tonnage requirements, the larger the equipment size selected. Large size equipment is appropriate for a production of about six million tons (total) per month, medium size for three mil- lion tons, and small size for one million tons or less.

Jan 1, 1973

By Huijun Shao, Qiang Liu, Zhengming Yi

The increase of the proportion of high Al2O3 content iron ore fine in iron and steel enterprises has brought about a series of problems such as the increase of the viscosity of blast furnace slag and the difficulty of the separation of slag and iron. In order to solve this problem, the effect of increasing MgO content on the technical and economic index, the cold strength, and metallurgical properties of high basicity and high-alumina sinter was studied through sinter pot test. Nova400NanoSEM field emission scanning electron microscope was used to analyze sinter microstructure. The experimental results show that when the MgO content fraction in the sinter with high basicity and high aluminum increases from 1.72 to 2.49%, the vertical sintering speed decreases by 4.38mm/min, the utilization coefficient decreases by 0.51t/(m2 h), and the low-temperature reduction degradation index increases by 6.7%. When MgO content in sinter is 2.11%, drum index and reducibility index are the highest, reaching 61.93% and 86.39% respectively. Mg2+ is mainly solid dissolved in the magnetite lattice and replaces Fe2+, up to 3.64%. The generated magnesie-containing magnetite inhibits the phase transition from Fe3O4 to Fe2O3 oxidation process in the sinter cooling process, which reduces the generation of secondary hematite and is conducive to improving the low-temperature reduction degradation performance of sinter.

Jul 4, 2021

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

The 1997 Rapid Excavation and Tunneling Conference (RETC) was held at the Mirage Hotel, Las Vegas, NV. The RETC is a biennial event jointly sponsored by SME and the American Society of Civil Engineers (ASCE). Conference attendance was 573 members, nonmembers and students, an increase of seven attendees from the 1995 conference in San Francisco, CA. Exhibitors occupied 51 booths at the Las Vegas RETC. The 1997 conference encompassed 58 presentations in 15 sessions. Participants were given details on achievements and advances that have resulted in new design solutions, alternative work practices and increased productivity within the industry. The page at the end of this article tells how to get your copy of the RETC proceedings, either hardbound or on CD-ROM. Or, if you wish, for the first time a CD-ROM is available with the complete RETC proceedings from 1972 to 1997. This two-disk, archival volume has key-word search capability, is in portable file format and is compatible with PC and Macintosh platforms. RETC program sessions included design and planning, ground support, tunnel boring machine (TBM) case histories, conventional excavation, new technology, difficult ground, geotechnical, shafts and raises, future/special projects, new Austrian tunneling method, international projects, soft ground case histories and water and gas. What follows are highlights of some of the RETC presentations.

Jan 1, 1997

By Yoginder P. Chugh

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1980

By T. J. Malterer

Peat has unique physical, chemical, and biological properties. These include high porosity and water retention, high absorption and adsorption properties, high buffering capacity, and it is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste treatment purposes. This paper reviews North American literature on the use of peat for waste treatment applications. The literature indicates promising use of peat in treating municipal and on-site effluent, removal of low concentrations of heavy metals from wastewaters, and adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1995

By Sara J. Heinlein, George Malkos, James E. Lindell, Tony Pestonatto

The 79th Street Water Tunnel Extension Project was initially designed by the City of Chicago, Department of Public Works, to increase the capacity of the City’s south side water distribution system. MWH preformed a design review, prepared the final design and provided construction management for the City of Chicago Department of Water. Construction commenced in September 1995 and was completed in October 1999. The Project connected two existing water tunnels with a new 5.8 km (19,044 ft.) long, 4.9 m (16.08 ft.) finished diameter concrete lined rock tunnel utilizing TBM, drill-blast and mechanical hoe-ramming methods. In addition, approximately 61 meters(200 feet) of concrete lined variable cross section tunnel, a new gate shaft and a temporary construction shaft were constructed. This paper describes the construction of these features and the geological conditions encountered.

Jan 1, 2003

By M. S. Moats, W. C. Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the United States. Electric arc furnace dusts, processed to recover zinc, produce a residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine its particle size, chemical composition, and predominant mineral phases. Heated, atmospheric, agitated leaching using sulfuric acid and hydrochloric acid was examined to determine the extractions of gallium, indium, and germanium as a function of concentration and temperature. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 71%, 63%, and 48%, respectively.

Feb 1, 2023

By J. Wiebmer

The two most important influencers of cost-per-ton in an underground mining machine are its productivity (tons/hour) and its availability-utilization (hours/year). Operating cost and initial price have far less impact. This paper reviews a cost-per-ton sensitivity analysis for underground mining equipment and discusses benchmarks for measuring its performance. The conclusion is that miner-supplier partnerships and the Information Age are the two most significant trends in cost-per-ton reduction.

Jan 1, 1997

By A. Janwong

Ion exchange technology is becoming more prevalent for metal recovery from low concentration solutions. The products of ion exchange are typically a metal free stream (product stream) and a concentrated metal stream (byproduct). The metals in the concentrate stream are usually precipitated and returned to the process or discarded. The unique features of emew® technology enable metals to be recovered directly from the concentrated stream. The advantage of the IX-emew® combination is the ability to have two product streams: 1) clean metal free solution and 2) metal product for sale. In addition to recovering metals from solution, it is also possible to separate metals from each other and recover more than one metal product. In this paper, examples of IX-emew® combinations are detailed including the recovery of copper, nickel and cobalt from an industrial waste stream, recovery of nickel from a spent electroless nickel plating solution and recovery of cobalt from an hydroxide cake.

Feb 23, 2014

By H. Cho

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal organic components could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation is dependent on the history of coal: the extent of liberation decreased when the size of the primogeniture coal decreased. The liberation of coal macerals was analyzed by examining the Liberation Index. It was seen that although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinitie), these particles were less liberated than the coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1996

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

By C. E. Ekburg

Gold Quarry is a sediment-hosted, epithermal disseminated gold deposit located along the Carlin Trend. Gold, hosted by allochthonous Ordovician siltstones and cherts, is localized at the intersection of structures sympathetic to the major Good Hope and Gold Quarry faults. The magnitude of Gold Quarry was discovered in 1979 by surface exploration and by percussion holes drilled near the Maggie Creek orebody. Four years of development drilling delineated an open pit mineable gold deposit that contains 130 Mt (144 million st) of ore at an average 1.68 g/t (0.049 oz per st) of gold and includes a high-grade core of 46 Mt (51 million st) that average 2.64 g/t (0.077 oz per st) gold. Milling of the higher-grade portion began in 1985.

Jan 1, 1987

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

By E. J. Rorem

Rockfall and unstable rock slopes can be con-trolled by using steel wire-rope net systems as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting. This flexibility and strength permits kinetic energy dissipation with low maintenance requirements. Mining activities can produce temporary or long-term unnatural slopes and unstable rock faces that may produce rockfall hazards. Such conditions can necessitate efforts to minimize the hazard to workers, structures and equipment.

Jan 1, 1996

By Robert J. Garino

Around two-thirds of world silver mine production comes from mines where the majority of ex-mill revenue is obtained from other metals. In this talk I will illustrate the importance of this output of silver as a by-product of the mining of various base metals. I will also consider the impact of relative changes in base and precious metal prices on mill-head revenue, and therefore, on production decisions. During the latter half of 1982 improving silver prices encouraged re-openings at several base metal mines. Thus some production of lead, zinc and copper can be regarded as partly conditional on the prevailing silver price. Conversely, a good deal of silver production can be considered to be independent of the silver price and dependent on the production of some base metal. It is the degree to which the value of silver mined affects the revenues of nominally, base metal, producers that is the central concern of this presentation.

Jan 1, 1983

By G. V. Sullivan

The Federal Bureau of Mines examined tailings samples from 13 western copper operations to determine the potential for recovering rutile. Results showed that six of the samples contained sufficient liberated titania to be considered potential sources. One sample contained 0.75 percent Ti02 or 0.40 percent liberated rutile. Batch flotation studies developed a procedure that recovered 70 percent of the liberated rutile at a grade of 34.7 percent TiO2. Sulfuric acid leaching studies on 12 of the samples dissolved 100 to 2,200 grams Cu per ton of tailings; leaching of the slimes showed slightly more copper was dissolved, 1,800 to 3,300 grams Cu per ton of minus lo-micrometer material. Bulk sulfide flotation of nine of the samples resulted in concentrates that contained 0.38 to 2.0 percent Cu and 0.7 to 2.1 and 6.9 to 42.9 grams per ton Au and Ag, respectively.

Jan 1, 1981