Search Documents

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant's -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By I. S. Parrish

As noted by McKinstry (1948), "How to deal with erratic high samples is one of the knottiest problems in ore estimation." He described a variety of approaches and methods to alleviate the problem through the averaging and weighing of assay data and by "cutting" or "clipping" of the erratic assays. Bird (1991) elaborated on ways of dealing with the nugget effect (erratics). He listed several procedures for cutting. Bird's list has been reproduced and/or added to by several authors including Vallee (1992) and Stone and Dunn (1993). Missing from each of these otherwise excellent reviews is a definition, description or guideline to recognition of an "erratic," or just where or when cutting is warranted or justified.

Jan 1, 1997

By Stephen Njoloma, Ivan Hee, Ravi Jain, Mina Shinouda

"INTRODUCTION DC Water’s First Street Tunnel (FST) is comprised of a collaborative effort between DC Water, DC Water’s Project Consultants Organization (PCO) led by Greeley & Hansen and McMillen Jacobs Associates and the design-build team of Skanska, Jay Dee, and Parsons Brinckerhoff. The fast-track project includes elements that were designed by the PCO and released for construction by DC Water prior to Notice to Proceed (NTP) and elements designed by the Design-Builder from 30% to released for construction after NTP. This required effective communication and technical coordination for integrated engineering and efficient construction. The project, constructed in an urban residential neighborhood, included innovative construction methods such as multiple location ground freezing, utilizing a centralized freeze plant, to minimize community impact. The means and methods chosen for cast-in-place shaft linings, precast segmental tunnel lining, microtunneling, sequential excavation method (SEM) adits and near surface elements reflected the immediate and sensitive surroundings, which varied by construction staging area (CSA). Technical aspects of the project, relative to the evolution from pre-bid to construction documents, are discussed along with modified designs to suit means and methods. SCOPE OF WORK In 2012, four major storm events swept through the District of Columbia and hit the Northeast Boundary sewer shed particularly hard with the neighborhood experiencing severe flooding. The extreme nature of the flooding, the damage to private property, and the health risks associated with exposure to sewage led to a multi-agency response and community calls for answers and action. The Mayor assembled a Task Force to evaluate a range of potential actions to address combined sewer flooding including engineering, regulatory, code revision, and management improvements. The Northeast Boundary Neighborhood Protection Project was the outcome of the Mayor’s Task Force; it is a three-step infrastructure initiative designed to offload the undersized sections of the existing collection system that serves the Northeast Boundary drainage area by implementing the McMillan Stormwater Storage Project, First Street Tunnel Project and the future Northeast Boundary Tunnel Project. Until the Northeast Boundary Tunnel Project is completed, the First Street Tunnel Project will add 8 million gallons of combined temporary sewer storage in a new tunnel under First Street NW to relieve undersized sewers that traverse the Bloomingdale neighborhood."

Jan 1, 2016

By Mark Alan Marlkos

Blebs of solid bitumen from the Magmont West orebody of the Viburnum Trend were examined and analyzed in an attempt to relate hydrocarbon distribution and origin to ore genesis. The bitumen was calculated to be approximately 48 to 63 percent aliphatic and is considered to be a polymerized normal crude oil. Polymerization, which was probably caused by water-washing, hardened the bleb surfaces and appears to have "frozen" the blebs during primary migration from local source beds. Comparison of the bitumen to kerogen in local shaly partings strongly Indicates that the oil was derived locally. The polymerized oil blebs are considered to have been derived from a type II (marine) kerogen. Textural analyses indicate that oil migration occurred after lead-zinc mineralization and at temperatures that exceed normal ancient or present geothermal gradients. The following sequence of events is postulated for the Magmont West orebody: 1 Generation of hydrogen sulfide during diagenesis of a normal organic-rich carbonate sequence. 2 Introduction of pulses of hot, metal-rich fluids that resulted in: a Lead-zinc mineralization by the following reaction: Me++ + H2S ? MeS + 2H+ b Solution of carbonates by excess acid produced during the above reaction. c Brecciation of host rock in some cases. 3 Passages of the pulse resulted in: a Carbonate buffering of fluid system to more alkaline conditions. b Precipitation of dolomite c Slight temperature drop. 4 Eventually the high temperatures Introduced by heated brine caused oil generation and initiated primary migration. 5 Water-washing and mild biodegradation altered the hydrocarbon blebs to their present composition.

Jan 1, 2013

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Henk L. C. Meuzelaar

Most of us are aware of the relationship between the golden-yellow resin spots on Upper Cretaceous Wasatch Plateau coals and fossil tree resins (?amber?). Nevertheless, confusion remains about the exact chemical composition and structure of commercial coal resin preparations as well as their observed heterogeneity. In order to arrive at a more detailed chemical description we need to distinguish between micropetrographic, organic geochemical and process technological definitions of coal resins, which may include substantial quantities of constituents unrelated to fossil tree resins. New information on composition and origin obtained by Curie-point pyrolysis/evaporation in combination with isobutane chemical ionization mass spectrometry, as presented in this paper, points to the presence of four more or less distinct resin components: (1) a sesquiterpenoid polymer; (2) sesqui-and triterpenoid monomers and dimers; (3) a suite of triterpenoid alcohols, ketones and acids; and (4) a series of increasingly aromatized hydrocarbons with naphthalene and picene type skeletons. Moreover, a strong similarity is found between the composition of recent Dammar resin and fossil Wasatch Plateau coal resins. Some of the technological implications of these findings and the consequent need for a more precise chemical definition and nomenclature are discussed.

Jan 1, 1990

By Steven A. Savage

Agrico Chemical Company, as we presently know it, is the result of the coming together of several different fertilizer operations. The Williams Companies, our parent organization, first entered the fertilizer business in 1971, when it acquired the fertilizer operations of the Gulf Oil Company. This gave us, among other things, the manufacturing facility at Donaldsonville, Louisiana. In 1972, The Williams Companies acquired Agrico Chemical Company from Continental Oil Company, bringing in a manufacturing facility and phosphate mines at Pierce Florida. Our Florida Mines are in the region commonly known as the Bone Valley Region of Florida. The majority of the phosphate fertilizer produced in the United States utilizes rock mined in this region. The Donaldsonville Plant was originally built in 1967-68 on the site of the old Faustina Plantation at an approximate cost of $80,000,000. (This plant is commonly referred to as our Faustina Plant.) Until such time as Agrico was acquired from Continental Oil, the Donaldsonville Facility was solely used to upgrade phosphoric acid into finished granular products.

Jan 1, 1986

By Huijun Shao, Qiang Liu, Zhengming Yi

The increase of the proportion of high Al2O3 content iron ore fine in iron and steel enterprises has brought about a series of problems such as the increase of the viscosity of blast furnace slag and the difficulty of the separation of slag and iron. In order to solve this problem, the effect of increasing MgO content on the technical and economic index, the cold strength, and metallurgical properties of high basicity and high-alumina sinter was studied through sinter pot test. Nova400NanoSEM field emission scanning electron microscope was used to analyze sinter microstructure. The experimental results show that when the MgO content fraction in the sinter with high basicity and high aluminum increases from 1.72 to 2.49%, the vertical sintering speed decreases by 4.38mm/min, the utilization coefficient decreases by 0.51t/(m2 h), and the low-temperature reduction degradation index increases by 6.7%. When MgO content in sinter is 2.11%, drum index and reducibility index are the highest, reaching 61.93% and 86.39% respectively. Mg2+ is mainly solid dissolved in the magnetite lattice and replaces Fe2+, up to 3.64%. The generated magnesie-containing magnetite inhibits the phase transition from Fe3O4 to Fe2O3 oxidation process in the sinter cooling process, which reduces the generation of secondary hematite and is conducive to improving the low-temperature reduction degradation performance of sinter.

Jul 4, 2021

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By Frank H. Buchella

Principal factors influencing equipment selection can be grouped into five basic categories. Tonnage Requirements, Ore and Waste Loading, transporting, and ground preparation equipment are largely determined by tonnage requirements. Generally, the greater the tonnage requirements, the larger the equipment size selected. Large size equipment is appropriate for a production of about six million tons (total) per month, medium size for three mil- lion tons, and small size for one million tons or less.

Jan 1, 1973

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By T. J. Fenner

Research conducted in South African mines has demonstrated the benefit of ground penetrating radar for the detection of geologic features and hazards. This is crucial for safety and production considerations in underground mines that are as much as 4 kilometers deep. This paper describes a new ground penetrating radar system designed specifically for high quality data acquisition, in the harsh conditions of deep underground environments, for use by operators with minimal geophysical experience. Design criteria included automated functions, intrinsic safety, light weight and minimal power requirements. Data is processed on the ground surface by geoscientists using a PC.

Jan 1, 1994

By J. W. Stevenson

At this 5th U.S. Mine Ventilation Symposium I would like to focus your attention on safety and the contribution of the ventilation engineer over the past 50 years. This conference affords us the opportunity to express, to listen, and to learn. As ventilation engineers it is indeed an exciting time--a time that not only stimulates our imagination but also pin points our aims in our quest to obtain zero fatalities by the year 2000, the goal expressed by William J. Tattersall, Assistant Secretary of Labor, Mine Safety and Health Administration. In the past, coal mine ventilation has often been unfortunately synonymous with explosions and resulting fires. Those not familiar with us do not recognize the painful evolution of the coal mining industry and particularly the evolution of mine ventilation. To put my presentation into perspective, I recently reviewed a U.S. Bureau of Mines Bulletin No. 586 - "Historical Summary of Coal-Mine Explosions in the United States 1810 - 1958 prepared by H. B. Humphrey Mining Health and Safety Engineer. This bulletin was published in 1960. Mr. Humphrey stated "In 1946, factors contributing to the explosions occurring from 1941 to 1945 were: (1) The rapid increase in the use of electrical equipment at face regions where gas and dust are most likely to be found; (2) the increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost, which in many mines has resulted in neglect of even rudimentary precautionary measures; (3) multiple-shift operation without provision of time for adequate maintenance of equipment, effective rock dusting, and testing for gas; (4) decrease in supervision owing to demands on supervisors for maximum tonnage and loss of competent supervisors to other employment; (5) lack of effective supervision, owing to numerous new conditions, some of them war-connected; (6) inability to obtain adequate equipment repair and replacement parts; (7) shortage of labor and inadequate training of coal-mine workers; and (8) failure of both miners and mining officials to show regard for safety in changing from hand-loading to mechanized methods". Most of the eight factors listed by Mr. Humphrey continue to affect our work lives as mining engineers. The increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost has never changed. The local and regionalized coal industry of the 40's is today competing against the world coal market. Our mines work or shut down based on cost. This has always been the case. During the five year time-frame Mr. Humphrey was documenting, 345 miners were killed in major explosions. A major explosion was one in which five or more miners were killed in a single accident. In addition, 105 more miners were killed in minor explosions for a total of 450. What a wanton waste of life. What fears, anxieties, miseries, and sufferings were created by these accidents. However, we must remember and keep in mind that the coal mining company officials, engineers, and foremen, the governmental agencies- federal, state, and local - were using the technical tools and knowledge available to operate the mines as safely as they could. Obviously mine ventilation engineering technology was woefully inadequate.

Jan 1, 1991

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By Yoginder P. Chugh

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1980

By M. S. Moats, W. C. Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the United States. Electric arc furnace dusts, processed to recover zinc, produce a residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine its particle size, chemical composition, and predominant mineral phases. Heated, atmospheric, agitated leaching using sulfuric acid and hydrochloric acid was examined to determine the extractions of gallium, indium, and germanium as a function of concentration and temperature. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 71%, 63%, and 48%, respectively.

Feb 1, 2023

By A. Janwong

Ion exchange technology is becoming more prevalent for metal recovery from low concentration solutions. The products of ion exchange are typically a metal free stream (product stream) and a concentrated metal stream (byproduct). The metals in the concentrate stream are usually precipitated and returned to the process or discarded. The unique features of emew® technology enable metals to be recovered directly from the concentrated stream. The advantage of the IX-emew® combination is the ability to have two product streams: 1) clean metal free solution and 2) metal product for sale. In addition to recovering metals from solution, it is also possible to separate metals from each other and recover more than one metal product. In this paper, examples of IX-emew® combinations are detailed including the recovery of copper, nickel and cobalt from an industrial waste stream, recovery of nickel from a spent electroless nickel plating solution and recovery of cobalt from an hydroxide cake.

Feb 23, 2014

By H. Lind

The consumption rate of Estonian oil shale increases due to the growing rate of exported oil-shale oil. Estonian oil shale active resources in working mines are predicted until the year of 2025 when the consumption rate stays at the level of 12 tons per year. If the consumption rate stays at that level, new mines should be opened after 20 years, if the rate increases new mines should be opened even earlier. The predicted active resources in Estonian oil shale deposits are calculated for 60 years, based on the parameters of the power station technicoeconomics. As a result, there is a need to open new mines. One of the potential areas for surface mine is the Tammiku-Kose prospect area (Rheinbaun Engineering, 1996).

Jan 1, 2006

By H. Cho

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal organic components could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation is dependent on the history of coal: the extent of liberation decreased when the size of the primogeniture coal decreased. The liberation of coal macerals was analyzed by examining the Liberation Index. It was seen that although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinitie), these particles were less liberated than the coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1996