Search Documents

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By James D. Bennett

Relationships among mine and injured miner characteristics and HSAC's degrees of injury are examined for 91,404 injuries in under- ground bituminous coal mines in the United States from 1975 through 1982. Injury severity varies by the mining system, geographical region, circumstances surrounding the injury, the injured miner's age, whether the miner was using powered equipment, the year which the injury occurred, and the location in the mine where the injury happened. Injury severity is not related to the injured miner's total mining experience, job experience, and experience in the mine in which the injury occurred.

Jan 1, 1984

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

A PDP 11/34 computer has been inter- faced to existing instrumentation in a 400 tph rod-mill/ball-mill grinding circuit and programed with a Kalman filter to estimate several unmeasured variables. A dynamic two-size- fraction model of the circuit is used to predict the complete state of the circuit including particle size distributions around the circuit, mass holdups and flowrates, the ball-mill grinding rate, water additions and cyclone parameters. Online measurements of sump level, slurry densities and product particle size are used to update the model values sequentially on a 20-second interval. This procedure results in optimal estimates of circuit variables given the relative reliability of measurements and the accuracy of the model.

Jan 1, 1983

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By W. S. Hannan

History Leaching of sulfide ore was first attempted by the Phelps Dodge Corporation about 1900 at Bisbee, Arizona, when Dr. James Douglas conducted experiments in an attempt to apply the leaching techniques then in use at Rio Tinto, Spain. Although this initital attempt was unsuccessful, research work was continued which culminated in successful leaching operations at Tyrone, New Mexico, in 1917 and at Bisbee beginning in 1920. Leaching has continued intermittently since that date, with material from the Lavender Pit being leached today. The Lavender Pit Leach Dump Stripping for the Lavender Pit was started in 1951, with mining operations on stream in 1954 and continuing to the present. All material removed from the pit has been classified as waste, leach material, milling ore, or direct smelting ore, depending upon grade and degree of oxidation. Lavender Pit leach material has been stockpiled in a single dump, called No. 7 Dump. This dump covers an area of approximately 135 acres and average about 300 feet in height. The dump has been deposited over a period of 20 years by truck haulage and contains several layers, each of which has a permeable boulder layer at the bottom and a compacted layer at the top. Leaching of Lavender Pit material was started in 1956 and has proceeded simultaneously with dump construction. Former leach pond areas and haulage surfaces have been ripped with D-9 tractors before deposition of succeeding layers of ore.

Jan 1, 1972

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By E. R. Pantos

US coal production increased 3% to a record 832 Mt (917 million st) in 1987, according to preliminary Energy Information Administration (EIA) data. Most of the increase was due to the unusually warm summer and the increased coal-fired electricity demand for air conditioning. Drought conditions in the Northwest lowered hydroelectric generation, contributing to the higher use of coal by electric utilities. However, excess production capacity and increased competition from natural gas added further downward pressure on delivered coal prices, continuing the declining price trend of the last several years. Coal production by region Appalachian coal production reached 402 Mt (443 million st) in 1987. This is about 3% more than in 1986 and just short of its 1984 peak. Virginia produced 7% more than its 1986 level, due to increased coal-based electricity demand. Smaller percentage increases were attained in eastern Kentucky, Pennsylvania, and West Virginia. Ohio and Alabama were the only major coal-producing states in Appalachia that produced less coal in 1987 than in the previous year. In the Interior region, 1987 coal production reached a record 182 Mt (201 million st), about 2% above 1986. Illinois is the largest coal-producing state in that region. Production there fell about 3.7%, primarily because of lowered demand at electric utility plants in Alabama and Tennessee. However, this was more than offset by production increases in western Kentucky, Texas, and Indiana. After falling slightly in 1986, coal production in the West resumed its upward trend to a record 248 Mt (273 million st). Wyoming is that region's dominant coal producer. It mined 7% more coal than in 1986. Wyoming's increase offset the 11% decline in New Mexico production and smaller declines in other Western states. Coal consumption and prices Domestic coal consumption reached a record 759 Mt (837 million st) in 1987. Most of the increase resulted from the unusually warm summer that led to higher than normal peak demands for electricity in the third quarter. Electric utility coal consumption was also boosted by the below-normal hydroelectric generation that resulted from low water levels in the Northwest. These factors more than offset the effects of increased nuclear power generation and competition from natural gas. As a result, coal provided 56.9% of electric utility generation in 1987, compared with 55.7% in 1986. Electric utilities consumed a record 651 Mt (718 million st) of coal. While electric utility coal consumption increased, the average cost of coal to utilities was down, from $1.58 per million Btu in 1986 to $1.52 in 1987. The average price of coal delivered to utilities in 1987 was $35.09/t ($31.84 per st), the lowest since 1981. Coal prices were held down by a glut of coal supplies and by a decline in the average price of natural gas to electric utilities. Coal consumption at coke plants in 1987 was 2.6% above the 1986's 32.5 Mt (36 million st). This increase reflects steel's recent resurgence. Coking coal demand, though, was reduced by the increased use of continuous casting and electric furnace technologies. The average price of coal delivered to coke plants fell from $56.02 to $51.35/t ($50.83 to $46.59 per st). Coal consumption in the industries other than coke plants amounted to 68.2 Mt (75.2 million st) in 1987, slightly less than in 1986. Coal lost part of its market share to natural gas, which was priced favorably relative to coal. The average price of coal delivered to manufacturing plants was at its lowest level of the current decade. It fell from $39.50/t in 1986 to $37.27/t ($35.84 to $33.81 per st). Residential and commercial coal consumption fell to 6.2 Mt (6.9 million st) that is 9.8% below 1986 and the lowest since 1980. This decline is also attributed to the relatively low price of natural gas in 1987. Coal stocks Coal consumers held 169 Mt (186 million st) of coal stocks at the end of 1987, 5.9% above the 1986 year-end level. Most of this increase was due to stockpiling by electric utilities in anticipation of a possible strike by the United Mine Workers of America early in 1988. Stocks at electric utilities increased to an estimated 154 Mt (171 million st) at the end of 1987, 5.6% higher than the previous year. This was much lower than 1984's stock buildup. Coke plants increased their coal stocks by 30% in 1987 to 3.5 Mt (3.9 million st), rebounding from the unusually low inventories of 1985 and 1986. Other industries increased their stocks slightly in 1987. Coal producers and distributors ended 1987 with 25 Mt (28 million

Jan 5, 1988

By R. C. Moe

Pelletizing studies were conducted to find ways of improving the metallurgical properties of acid and fluxed pellets. In acid pellets, melting temperature was controlled by the formation of low melting temperature fayalite during reduction. Formation of a permeable metallic shell during reduction allows diffusion of reducing gas to the pellet core, decreasing fayalite formation. With fluxed pellets, slag chemistry had the main influence on metallurgical properties. Mineralogical, chemical and structural transformations that occur during reduction were studied at various intervals for a number of Mesabi Range pellet types. Six pellet types were selected for further investigation based on significant differences in softening/melting characteristics. Retention of porosity in the metallic shell was found to be the overriding factor in determining softening/melting behavior.

Jan 1, 1990

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"BACKGROUND The design, development, fabrication, and test of a cryogenic supply for a refuge alternative is part of a larger effort funded by the National Institute for Occupational Safety and Health and managed through a Space Act Agreement with the National Aeronautics and Space Administration at the Kennedy Space Center, FL to create cryogenically based life support equipment responsive to the needs of miners as required by the Miner Act of 2008. This work is done by a joint contractor/NASA team. In particular, the Cryogenic Refuge Alternative Supply System (CryoRASS) serves to provide a respirable air source to miners confined for 96 hours in a mine refuge alternative. This system stores liquid air in a zero-loss cryogenic reservoir (Dewar) until an emergency requires use. The system does not require electric power when in use by miners. Because of the very cold nature of the liquid air, considerable heat stress relief and reduction of humidity is provided in addition to the required replenishment of oxygen. Moderate dilution of CO2 also occurs.INTRODUCTION The design of this new cryogenic refuge alternative supply system (CryoRASS) uses NASA/Kennedy Space Center technology as a development baseline. The design stores cryogenic (liquid) air that is warmed in an air handler box and the resulting gaseous air is introduced to the chamber that not only causes air circulation, but relies upon environmental and human heat to expand the liquid air to a gaseous state. Therefore, the primary benefits of the liquid air source, besides atmosphere maintenance (oxygen), is refuge cooling and dehumidification. This results in reduction of human heat stress and this occurs without the need for electrical power in the refuge chamber. This reduction is a major factor in ""apparent heat"" and the human perception of comfort. Another benefit with introduction of ""air"" vs only ""oxygen"" is the dilution of carbon dioxide. The volume of new air will displace existing refuge air and this air laden with humidity/CO2/low O2 passes out of the refuge relief valves. These RVs should be strategically placed to vent stagnant air preferentially. An initial system test was conducted in our Florida facility in a production 10-person hard chamber for 96 hours. Last year (2014) the system was tested with a 23 person inflatable refuge alternative in Bruceton. For this test, the CryoRASS air handler was redesigned to offer superior characteristics when installed in a Built-in-Place refuge alternative. This report describes the results of the modified system being tested in the Pittsburgh Experimental Mine while attached to a 30 person refuge for 96 (+/-) hours."

Jan 1, 2016

By Raymond O. Dannenberg

Potential processes for the recovery of precious metals and copper from diverse types of complex electronic scrap were investigated. Leaching-type processes were not successful, and attempts to physically separate the various gangue metals and plastics from more valuable components were also unsuccessful. The most promising approach was a smelting process, followed by electrolytic treatment to separate precious metal from copper. Recovery of precious metals from the anode sludge may follow conventional procedures. An alternative to the above process is incorporation of the scrap with the concentrate fed to an industrial copper reverberatory or converter furnace, possibly preceded by direct melting to form an assayable bullion and dross.

Jan 1, 1970

As we are all well aware, the demand for coal is increasing very rapidly. This makes the coal industry one of great opportunity for both the miner and the-supplier. Up until the middle 1960's, the price of coal had been one of the most stable of all commodities for the proceeding fifty years. In somewhat oversimplified terms this was because the inflationary tendencies had been offset by improved mine techniques and more efficient, more productive, and more reliable equipment; but, in the last seven years the price of coal has doubled. It is not the intent of this paper to discuss the many reasons for this price increase, but to show how the cost of hauling coal can be sharply decreased with a new truck concept. Not long ago a mining executive stated that all haulage trucks now available are basically the same. They look the same; they cost about the same; they have the same engine, power train, and tires; and, they have about the same operating cost. Truck size has increased which has reduced the number of drivers, but the purchase price and maintenance and repair costs have increased proportionally. Pits must be widened and loading shovels enlarged, out, all this has not reduced the cost of moving coal. Another executive said that he saw no advantage in buying new trucks because his people now know how to maintain and operate the ones they presently have. They have all the right spare parts along with a good maintenance program. Most replaceable parts of the trucks now in operation have been replaced and improved at least once and the trucks are now running better than when they were new. Besides, the trucks are no pretty well written off.

Jan 1, 1972

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997

By Christopher E. Dianora, Matthew Sorrell, Eileen Test

"Constructed between 1939 and 1945, the Rondout-West Branch Tunnel (RWBT) portion of the Delaware Aqueduct is 45 miles (72 km) long. The New York City Department of Environmental Protection (NYCDEP) first identified suspected areas of leakage from the RWBT in the 1990s. A $1 billion project is underway to mitigate the leakage through the construction of a bypass tunnel around the area of most severe deterioration, a 2.5-mile (4 km) section located beneath the Hudson River. Two shafts, 800 and 900 feet (244 and 274 m) below the ground surface, are being sunk to support the tunnel construction. The deep shafts will be subjected to high groundwater pressures and have been designed to accommodate multiple tunnel portals. This paper discusses the engineering decisions and analyses leading up to the final design. INTRODUCTION Project Background The New York City Department of Environmental Protection (NYCDEP) provides over 1 billion gallons (3.7 billion liters) of water to over 9 million residents of the City of New York and surrounding communities each day. This water is stored in upstate reservoirs and conveyed to the City via a system of aqueducts and tunnels. Water is delivered to the City almost completely by gravity and consists of three systems: the Croton, the Catskill, and the Delaware. The Delaware System is the largest of the three and supplies between 50% and 70% of the City’s daily water supply. In the 1990s, the NYCDEP discovered leaks in the central 45-mile-long (72 km) portion of the Delaware Aqueduct known as the Rondout-West Branch Tunnel (RWBT). The leaks release between 15 and 35 million gallons per day (MGD) (132.5 million liters per day) and are concentrated in two areas near Wawarsing and Roseton, New York. As part of the Rondout-West Branch Bypass Tunnel and Wawarsing Repairs Project (Bypass Tunnel Project), the leaks in the Wawarsing area will be repaired by grouting from inside the existing RWBT, and the leaks in the Roseton area will be mitigated by constructing a bypass tunnel parallel to and 1,750 feet (533 m) north of the leaking portion of the existing RWBT. Two deep shafts will be excavated on either side of the Hudson River: Shaft 5B in Newburgh and Shaft 6B in the Town of Wappinger."

Jan 1, 2016

By Raymond K. Will

Computers are becoming increasingly valuable tools in the mining industry as a greater variety of appropriate hardware and software becomes available, combined with greater acceptance by management, Within a given time period an engineering staff can evaluate or design a project to much greater detail and higher accuracy by utilizing computers once suitable programs have been developed. We are all aware that throughout the world the decreasing grade of minerals coupled with increasing waste to ore ratios necessitate larger capacity, longer term mining operations and attendant higher capital costs. Computers can be of assistance in all stages of mineral exploitation, from geologic exploration through mine feasibility studies and design, to marketing and transportation. Because of the high speed with which data can be digested and manipulated by computers, preliminary information from any stage of investigation can be analyzed to assist in further guidance of that stage. By use of preliminary mine feasibility studies, financial forecasts and sensitivity analysis, even information from a far-removed phase such as marine transportation of the product, can help guide the exploration phase to a realistic target.

Jan 1, 1973

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990