Search Documents

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By K. H. Nimerick

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 1, 1977

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By Y. Akin

The floatability of a typical boron mineral, colemanite (Ca2B6O11.5H2O), is shown to be hindered by the presence of montmorillonite type clay minerals. The clay is found to act in the form of slime coating. The mechanism of slime coating is investigated using pure colemanite and clay and their mixtures with an anionic reagent in a microflotation cell. Adsorption, flotation, solubility, zeta potential and scanning electron microscope studies reveal that slime coating occurs through electrostatic attraction. It is possible to minimize the effect of slime coating either at high surfactant concentration or at high pH values.

Jan 1, 1997

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today's ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980

By O. J. Malacarne

The use of a series of thickeners for-washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The, common, practice is to wash the sand fraction in classifiers and, the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear, Company, a total ore' acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1,000 to 1,300 tons per day in a series of washing thickeners. A typical screen. analysis of the ore being washed in these thickeners, is 25 percent -200 mesh, 3 percent +35 mesh and about, one' percent +l4 mesh., The amount of slimes (-200 mesh) will vary from 20 to 30 percent s the mill receives ore from 150 different mines The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and of course ally acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Company is located in Montrose County, Colorado and is physically located on a canyon wall along the San Miguel river. The thickeners referred to in this, paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north.

Jan 1, 1962

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By Donald G. Foot

The Bureau of Mines, U.S. Department of the Interior, devised a direct flotation method for treating low-grade carnallice (KC1.MgC12. 6H20) and sylvinite (a mixture of KC1 and NaC1) ores characterized by a high content of water-insoluble impurities. The procedure consists of (1) flocculation-depression of the insoluble slimes, (2) decomposition leach (carnallite only), (3) potash rougher, cleaner and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid-phase KC1 from carnallite ore and 79.7% of the KC1 from sylvinite ore in final products containing 60.5% and 60.9% K20, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1981

By Drummond Earley III

The U.S. Bureau of Mines is currently conducting laboratory experiments to study the reactions occurring during in situ leaching of oxide copper ores hosted by biotite-poor granite and biotite-rich granite porphyry. Detailed pre-leach and post-leach petrographic examinations of the rock samples are combined with the leach solution chemistry resulting from core leaching experiments to enable an evaluation of the various reactions which are responsible for the observed fluid chemistry. The information resulting from these laboratory studies is being utilized to support the design of the Bureau's ongoing field research project at the Santa Cruz deposit near Casa Grande, AZ. Atacamite and chrysocolla are the primary copper minerals present in this deposit, and both are readily soluble in the dilute 5% sulfuric acid solutions used in these experiments. In addition to the dissolution of copper minerals, biotite dissolution also occurs during the experiments, contributing K, Mg, Fe, and Al to the leach solution. The biotite dissolution appears to be non-stoichiometric, as it is progressively altered to vermiculite and finally, amorphous silica. While K, Mg, and Fe concentrations in solution steadily increase with time, Al quickly reaches a maximum, and then remains relatively constant for the remainder of the experiment. This suggests that Al saturation is achieved, and this Is supported by the presence of precipitated Al sulfate and aluminosillcate clay mineralization in the post-leach rock samples.

Jan 1, 1990

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961

By A. D. Davis

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well defined drainage in a heavily mineralized area of the northern Black Hills. The basin contains numerous inactive and abandoned mines as well as a currently active heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer and thus can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted, and two abandoned mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 1997

By F. B. Brost

In 1976, a decision was made by Anamax Mining Company to install an unusual conveying system to transport ore 10.3 km (6.4 mi) from the new Eisenhower Mine to the Twin Buttes concentrator. The system, supplied by Cable Belt Limited of the United Kingdom, represents a radical departure from conventional belt conveyors. The driving tension is applied through two endless wire ropes driven by a single 2 240 kw (3 000 HP) drive while the belt acts only as the ore carrying medium. Full production was begun in January, 1979. Start-up problems hampered production for several months but were resolved by a joint Anamax-Cable Belt effort. The system has been operating at design capacity for 4-1/2 years, and has proven itself as a reliable, low cost ore transportation system.

Jan 1, 1984

By L. G. Closs

Gold continued to be the primary focus of minerals exploration worldwide during 1995. Other targets, though, included primary diamonds and base metals, especially copper deposits amenable to solvent-extraction/electrowinning (SX/EW) processing. The discovery of nickel, copper and cobalt at Voisey Bay in Labrador, Canada was an unusual surprise. Meanwhile, exploration geochemistry continues to evolve to meet new challenges. The major event in this category during 1995 was the17th International Geochemical Exploration Symposium (IGES) held in Townsville, Queensland, Australia in May. The meeting was sponsored by the Association of Exploration Geochemists, which celebrated its 25thanniversary of service to the mineral industry, and the Economic Geology Research Unit of James Cook University, Townsville.

Jan 1, 1996

By Elza Burch

Introduction The feeding to zero concept involves feeding 600 µm x 0 (28 mesh x 0) size raw coal to heavy media (magnetite) cyclones along with the +600 µm (+28 mesh) size coal. Traditional circuits employ desliming or removing the 600 µm x 0 (28 mesh x 0) size fraction and feeding the cyclones +600 µm (+28 mesh) size coal. The feeding to zero concept recirculates 600 µm x 0 (28 mesh x 0) fines in the circuit. At the same time, a portion of the fine material is continuously withdrawn and recovered. This, in turn, prevents a fines buildup. This concept eliminates desliming screens and secondary fines circuitry for recovery of 600 x 150 µm (28 mesh x 100 mesh) coal. The result is a very simple circuit. Feeding to zero at Island Creek Island Creek Corp. was the first involved with the new concept in 1976. The company needed a temporary plant for the 9.5 mm x 0 (0.4 in. x 0) raw coal at its Pond Fork mine, near Madison, WV, while a full-scale plant was being designed and built. At that time, the Childress Corp., of Beckley, WV, became interested in the feeding to zero concept. Island Creek awarded a contract to Childress to build a single cyclone modular plant, incorporating this feeding to zero concept. The plant was erected in three months. The Pond Fork modular plant proved successful in attaining the desired feed rate of about 63.5 t/h (70 stph), while maintaining good separating efficiencies and low magnetite consumption rates. The 9.5 mm x 150 µm (0.4 in. x 100 mesh) clean coal was recovered and the 150 µm x 0 (100 mesh x 0) size was disposed of to waste. The full-scale plant was completed about two years later and the Pond Fork modular plant was moved to Holden, WV. There, it was incorporated into the Holden 29 preparation plant as a separate circuit for cleaning -25 mm (-1 in.) coal. In 1976, a similar plant was installed in Virginia by another company. These two plants are believed to be the first two operational plants in the United States incorporating the feeding to zero concept. Island Creek subsequently contracted with Childress for an identical plant at the Coal Mountain operation in West Virginia. The plant operated for three years before the mine was closed. The unit was then moved to the Spurlock mine near Martin, KY where it continues to operate. The successful operation of the Pond Fork and Coal Mountain plants before and after relocation proved both the performance and moveability of this type of circuit when constructed in a modular fashion. Since the first two plants were built, Island Creek has incorporated the feeding to zero circuit in nine additional plants. A grand total of 33 cyclones have been installed using this concept. One is the Providence mine, near Providence. Providence preparation plant Island Creek contracted with J.O. Lively Corp. of Glen White, WV in July 1978 for the construction of the Providence preparation plant. The plant began operation in February 1979. The construction period was about halved by building the plant with modular design concepts. Prefabricated sections, floors, and sides were brought in as units and then bolted in place. The Providence plant has a good track record of processing coal at a feed rate of 454 kt/h (500 stph). Feed coal to the plant has an average ash content of about 18% and sulfur content of about 4.5%. It contains about 22% refuse. The coal product has an average ash content of about 8% and sulfur content is about 3%. Raw West Kentucky No. 9 seam coal is conveyed from a box cut in the Providence mine to a rotary breaker. The breaker is fitted with 74 mm-diam (3 in.-diam) opening breaker plates. Therefore, it is well suited for removing trash, roof bolts, wood, and pyritic balls that are common in Illinois Basin coal. The -75 mm (-3 in.) coal is conveyed from the rotary breaker to

Jan 8, 1987

By J. M. Mutmansky

This paper outlines patterns of methane emission in both longwall and room-and-pillar operations and the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane drainage system will be discussed as well as the costs related to the production of coal. The important issue of production slowdowns and gas outs will also be discussed as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems will be made as well as justification for more intensive economic analysis of coalbed methane extraction and utilization.

Jan 1, 1998