Search Documents

By W. F. Riggs

INTRODUCTION Flotation equipment is becoming more definitive in design as well as greater in dimension. The last ten years have witnessed the implementation of large flotation cells ranging in size from 28 to 85 cubic meters. However, small plants still operate with cells as small as 3 cubic meters. These changes have increased the operational sensitivity of the flotation system to the chemical reagents used. No scientific study has been undertaken to develop the relationship between the size of equipment and the response of reagents in the flotation system. Hence, this article is an attempt to present several observations from past experience for the purpose of stimulating future research in an area previously ignored and perhaps subsequently not used to advantage. CONVENTIONAL FLOTATION Recent advances in conventional flotation cell design have been made in two areas: a. Flotation cells are becoming larger, and b. Basic design of flotation cells has changed. They can be classified into two types: deep cell and shallow draft cell. Size and design changes of flotation cells have a greater effect on frother performance than on the performance of other chemical reagents. Hence, the discussion in the following sections is restricted to the impact of frothers in the flotation system. Flotation Cell Size The advent of increasing flotation cell size has resulted in the increase of frother consumption. There appears to be a correlation between reduced horsepower (kilowatt) consumption and increased frother consumption per ton of ore processed in the circuit. This is more prevalent when the frother chemistry remains unchanged. Another reason for increased frother consumption is the increased distance between the rotating central shaft and the lip of the cell for larger flotation machines. Increasing this distance results in increased surface area corresponding to the larger cell size. Reduced power input per ton combined with the need for longer, stronger load support of the froth bubble as a result of increasing cell size has resulted in the development of a new series of stronger and more persistent frothers. By the same token, these newer, stronger frothers are difficult to control when applied to the smaller cells. This is true even at lower dosages because the break point between too much frother and not enough frother for optimum metallurgy is normally very narrow. This problem is often exaggerated when operators have established an optimum setting for pulp level and air for the particular frother in use. Generally, the tendency is to operate the flotation cells simply by adjusting frother dosage. The increase in frother strength to accommodate the large cells often results in the realization, after a retrofit, that the existing pump box or sump which is still handling the same volume of concentrate is no longer adequate in size. Flotation Cell Design The two most common flotation cell designs installed during the past ten years are the deep cell and the shallow draft cell. The deep cell provides for complete mixing of air and pulp at the bottom of the cell. The shallow draft cell does all the mixing/pumping in the bottom haft of the cell whereas the mixing of the air is performed further up the shaft and is brought into contact with the pulp midway up the vortex. There are many preferences for one or the other. It is the author's contention that both designs have very valid concepts and must simply be suited to the particular situation as required by the operator. The following comments are subjective observations which should be explored in greater detail. The deep cell mixes both air and pulp together at the bottom of the cell requiring a full depth ascending of the homogenized air to the surface to form the froth layer. This design, in combination with charged air, provides for good concentrate grade control under adverse conditions of selectivity, especially when faced with a fine grind and a slime-laden gangue. A selective frother can be applied without a competitive loss in recovery. One of the conditions for good selectivity in this environment is operating at medium pulp solids concentration in the range of twenty-six to thirty-four per cent (26-34%). When a higher solids concentration is used in combination with a coarse grind, it becomes difficult to maintain the same recovery with a selective frother due to higher pulp viscosity. This condition sometimes results in an unacceptable coalescence of the air bubbles as they ascend the full height of the deep cell. The increased pulp viscosity at higher solids concentration can also retard the flotation kinetics. The combination of decreased surface area of dispersed air and slower kinetics can result in reduced recovery causing coarse particles to continue to drop

Jan 1, 1989

By Jozef Stachulak

Prof. H. Bystron: "An Application of the First Law of Thermodynamics to Winter Dry Air Flow in Mr. Stachulak's Mine Model". [ ]

Jan 1, 1980

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By R. J. McGregor, Deepak Malhotra

Engineers frequently encounter situations where decisions that are counterintuitive to the logically trained engineering mind are made because of other influences, whether they be financial, social, cultural, or environmental. Such influences can overrule the "logical" decision-making process. The aim of this book is to explore some of the nontechnical issues, which most engineers don't learn about in school, that can have a major impact in the mining industry. This chapter gives a brief overview of this volume and introduces the topics that will be addressed.

Jan 1, 2001

By R. G. Reddy, A. E. Torma

Bio-treatment of uranium contaminated soils from Fernald using the bacterium Thiobacillus ferrooxidans was investigated. The experimental results showed that extraction of uranium upto 99 percent from soils were obtained with 10 percent pulp density suspension and with addition of iron (3000 mg/l) after bio-remediation time of seven days. Application of the results to industrial practices is discussed.

Jan 1, 1995

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By William R. Nash

Case histories of water problems in underground mine shafts and tunnels are outlined to illustrate varying degrees of sophistication in grouting techniques currently applied in such construction. The interception of water underground can be one of prior knowledge, i. e., the site investigation provides necessary data to plan a grouting program prior to construction start, or excavations may encounter "changed conditions" or unplanned water. The latter includes catastrophic inflows and emergency situations where the structural integrity of a building or concrete shaft lining are jeopardized. The presentation of this paper outlines some applications of grouting work in underground mine construction throughout the United States in a variety of geological provinces and for a variety of minerals.

Jan 1, 1984

By G. Davis

It is well known that the anticipated mineral price at the start of a prospective mineral project can have an overwhelming effect on a property's ex ante value. However, possible price movements throughout the life of a project can also have an impact on this value. This paper demonstrates how different potential price paths can affect project value. When considering commodity price projections for mine valuations, it is thus necessary to estimate not only the expected commodity price at the start of the project, but also the manner in which that price is likely to fluctuate throughout the project's life.

Jan 1, 1995

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By H. Shafick Hanna

The beneficiation characteristics of low grade Birmingham red iron ores of the Big Seam and Ferruginous Sandstone seams were investigated using flotation and magnetic separation after reduction roasting. Samples of Bib Seam Ore responded more readily to concentration than the Ferruginous Sandstone ores. The impurities inherent with the iron oxide minerals limit the grade of concentrates recoverable from these ores to a maximum of about 61% Fe if reasonable iron recoveries are sought. Flotation concentrates assaying 60-61% Fe and about 0.1% P with attendant iron recoveries of about 63% were achieved from Big Seam ore charges while those obtained from the low phosphorus Ferruginous Sandstone samples analyzed 54-56% Fe. Reductive roasting and magnetic separation of ground charges of the two ore samples yielded concentrates assaying 60-61% Fe. Iron recoveries were better than those achieved by flotation, but the magnetic products of Big Seam ore were high in phosphorus (0.2-0.3% P).

Jan 1, 1983

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The effectiveness of the grouting of saturated, fractured rock in the vicinity of underground workings depends to a great extent on the correct interpretation of the specific hydrogeological conditions at the site. During the planning of grouting operations, calculations of the hydrogeologic co-efficients and of the parameters of the isolating grout curtain(s) and the procedures for forming the curtain(s) must be based on valid hydrogeologic characteristics of the fracture system of the rock within each hydrostratigraphic unit (Anon., 1976). This chapter presents a discussion of the background information that must be collected for these purposes. Details of testing are presented in Chapter 3. The general design of new or the reconstruction of existing underground workings requires a broadly based organization having the expertise to develop a grouting operations plan once it acquires the necessary information. The needed information includes: 1) general information about the hydrogeologic section, 2) the engineering design of the underground workings, 3) the geology of the region, 4) the hydrochemistry of the ground water, 5) the hydraulic properties of the rock, 6) the characterization of all gases present, and 7) characterization of the rock's physical-mechanical properties which is necessary to avoid or control hydrofracturing . The geological documentation portion of the hydrogeological investigation is prepared based on the results of geologic mapping, geophysical surveys and on geo-exploratory operations at a regional and local scale. Geological data from the excavation of other underground workings in adjacent areas of the region is also included. Finally the results of site specific investigations in boreholes constructed at the site of the proposed underground activity are incorporated. A section of the preliminary report entitled "General Information about the Project Site" patterned after the parent STG guidance document on this subject must be com- piled based on the contents of geological reports and on the general construction plan for a new project or the plan for reconstruction of an existing operation. This section of the preliminary report must contain concise information about the conditions under which the planned grouting operations are to be conducted. The information must cover the geo- graphic, administrative, and economic subject areas also. Information about sources of electrical power, heat and water supplies, the presence and characteristics of local construction materials suitable for making grout (particularly clay and cement for the clay-based grout), transportation, and the status of communication lines and other services must be included in this section. Map scales for this section should be on the order of 1:25,000. The technical characterization of planned underground workings is presented in a project report chapter called "General Construction Plan for a New or the Restoration of an Old Operation. " The characterization comprises concise information about the purpose of the workings, the planned depths (for shafts) and the length (for horizontal and inclined workings), the inside and excavated diameters (for shafts), the cross-sectional area (for inclined and horizontal workings), and the face and mouth markers. If excavated underground workings exist in the region, then a concise description of them must be provided. The characterization of all excavations and all operational conditions must be specified. The location within the general structure of the proposed operation is specified. Flow charts must be included in this section that show: 1) the plan for opening the deposit, 2) the plans of the mining operations, and 3) the planned geological sections as they relate to the main workings. These graphical flow charts and appendices are drawn in scales of 1:2000 or 1:5000. 2.1 GEOLOGICAL CHARACTERIZATION The geological characterization of a site of proposed underground workings includes the following principal subject areas: stratigraphy, lithology, structural geology and a characterization of the status of fracturing. 2.1.1 STRATIGRAPHY AND LITHOLOGY A description of the geological section of the rocks to be intersected by the planned underground workings is complied on the basis of: 1) research data derived from core extracted from exploratory boreholes and monitoring boreholes, 2) the documentation and mapping of all natural out- crops in the region, 3) the data from all existing under-ground workings in the regions where operations are being canied out already, along with data from adjacent regions, 4) the data from surface and borehole geophysical investigations (standard and specially developed logging methods, and 5) regional stratigraphy. The geological description of the rock must express the maximum detail possible. The description provides the name of the rock, the granulometric composition (for fragmented rock), the composition and type of stratification, the drilling characteristics of the rock, a visual estimate of porosity and density for each stratum identified, the karstic

Jan 1, 1993

By John T. Atkins

Utah International's Shirley Basin Mine is located in the Southeastern High Plains of Wyoming at an elevation of about 7,100 feet. The Shirley Basin area is a gently rolling semi-arid land. The uranium ore zone occurs at depths ranging from 270 to 350 feet below the surface. Overburden consists of poorly consolidated sandstones, siltstones, and clays. Underground mining was begun in 1960. Conditions were made difficult by high rates of water inflow and ground support problems. The development of a solution mining I or in-situ leaching technique allowed underground operation to be abandoned in 1964. Solution mining provided limited production from 1963 to July 1970. In January, 1969, large scale development of open-pit mining was begun. A 1,200 ton per day mill went "on stream" in March, 1971.

Jan 1, 1973

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By Samuel S. M. Chan

Rock surrounding mine openings frequently is an impermeable type such as shale or granite. Most rock, however, has joints, bedding planes, cleavage planes, or other potential discontinuities. Permeability to fluids (gas or liquid) may exist via natural joints or fractures in an otherwise impermeable rock. In the mining situation, tectonic and induced tensile and shear stresses may be great enough to cause joints to open or fractures to develop in previously solid rock. The rock, as a result, becomes less self-supporting and may - require artificial support such as rock bolts or timber. Simultaneously, as fractures develop, permeable paths may be created. If fluid can be injected into a previously solid and impermeable rock mass, a logical conclusion is that a fracture (crack) flow path must be transmitting that fluid. The U.S. Bureau of Mines Laramie (Wyo) Energy Research Center has been evaluating results of in-situ oil shale fracturing (hydraulic or explosive) and retorting experiments by. a fluid (air) injection , and borehole air flow profile logging technique since 1956 (1, 14, 15). In the oil shale case, it is imperative to know the location and flow capacity (permeability) of natural fractures, if they exist, and induced fractures that inter-connect vertical wellbores at depths of fifty to several hundred feet. By injecting air into one wellbore in a system of several wells and measuring input volume and pressure while simultaneously measuring the output of other wellbores, the minimum areal extent of interconnecting permeable fractures can be determined. Exact locations (depths) of fractures and individual fracture flow capacities between wellbores can be determined by air flow profile logging (14, 15). Knowledge of fracture locations and permeability is essential to rational experimental in-situ retorting design.

Jan 1, 1973

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By R. E. Brewer

Phelps Dodge Mining Company (Phelps Dodge) is operating a pressure leach vessel (PLV) for copper concentrates at the Bagdad Mine facility in Arizona. This single PLV unit was engineered and constructed based on continuous laboratory testing, reaction chemistry and kinetics, and available pressure vessel technology. The challenge of designing for optimum process retention time, agitation, oxygen mass transfer, temperature and pressure will be reviewed in this paper. The PLV interior lining, agitation equipment and compartment configuration chosen for the PLV will also be reviewed.

Jan 1, 2004