Search Documents

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By M. Kaya

This paper presents an experimental method to determine the degree of gangue entrainment in mechanical flotation cells and proposes new and inexpensive methods to lessen it. The applicability of froth washing and vibration was studied in laboratory, pilot plant, and plant scales. The effect of wash water on metallurgical performance was tested with various streams from the Falconbridge Strathcona mill at laboratory, pilot, and plant scales, with the 2nd cleaner at the Eastmaque Kirkland Lake mill, and with the 2nd and 3rd zinc and 3rd and 4th copper cleaners at Les Mines Selbaie mill. It was found that gangue recovery was closely related to water recovery in all systems. Wash water at an optimum superficial rate from 0.03 to 0.07 cm/s reduced entrainment by anywhere from 30X to 70X. Wash water can be further assisted by mechanical and ultrasonic vibration of the froth. A further rejection of 10 to 20X becomes possible. As a result of this work, a number of plants in Canada and in the United States have evaluated and/or are now using froth washing.

Jan 1, 1990

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

By Carl E. Brechtel, Edward D. Thimons

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kw (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1987

By G. R. Brunskill

The molybdenite flotation plant at Magma Copper Company, San Manuel concentrator has been in operation since 1956. In January of 1980 the plant was converted from a hydrogen peroxide - ferrocyanide process to the current sodium cyanide - sodium hydrosulfide process. This paper is an operational review of Magma Copper Company's molybdenite recovery circuit, column cell flotation experience and use of on- stream x-ray flourescence analysis.

Jan 1, 1985

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By V. A. Shea-Albin

Sandstone escarpments surrounding western coal-bearing plateaus serve as critical habitat for animal species. Effects of mining subsidence on escarpment stability are not well documented; therefore, regulatory agencies may limit extraction of coal reserves underlying escarpments. Because millions of tons of this coal exist on Federal Lands, associated public revenues from Federal royalties, and valuable coal reserves, risk being lost. The U. S. Bureau of Mines is using numerical modeling techniques to analyze effects of subsidence on escarpment stability. Finite element models that incorporate bedding plane slip, gob formation, and movement along joints simulate escarpment subsidence observed in the field.

Jan 1, 1994

By James Wm. White

Computer based dispatching in open pit truck haulage operations yields many benefits of current interest to mine management. The key tangible benefit is a substantial productivity increase with a given fleet of equipment or, alternately, a significant reduction in equipment required to meet production quotas. Other tangible benefits, depending on the operation, include minimizing rehandle, meeting several blending constraints simultaneously and ensuring a target plant feed rate. Intangible benefits include production forecasting, performance comparisons of trucks or shovels of different manufacture and extensive on-line report generation. Recent advances in mini and micro computer hardware and software and solid state electronics permit design and implementation of system features not feasible even a few years ago. Here we discuss many of these recent developments with emphasis on system aspects and dispatching algorithms.

Jan 1, 1983

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By P. R. Hervey, J. W. Foise

Quartz is the second most widely used electronic material, with approximately 3,000 t (3,300 st) of single crystals used each year. Most of the quartz used in electronics is synthetic and is manufactured using a technique called hydrothermal growth. This paper reviews the basics of hydrothermal growth, the feedstocks used for these crystals and the challenges to improving the growth process. This paper also reviews the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 2002

By A. K. Gangopadhyay

This paper discusses the effect of grinding media composition, mineral type and slurry environment on the wear rate of various grinding media (balls). Sufficient wear data have been obtained and correlated with the modes of wear determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1984

By A. Bergmann

Location The Meggen Mine and the concentrator plant of the "Sachtleben Bergbau G.m.b.H." are located in the southern part of the Ruhr-district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was built in 1962 and started up in January 1963. Goelogy and Mining The Meggen ore-body is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonion age. The average thickness of the deposit is 3 meters and, due to an intense folding of the area, the mineralized zone dips very steeply at 800 toward the north. The ore consists of 85 percent of sulfides and 15 percent gangue that mainly contains silicates from the host rocks. The principal ore minerals are pyrite (67 percent), sphalerite (16 percent) and galena (2 percent) with minor amounts of marcasite and only traces of chalcopyrite. As shown in Fig. 1, the sphalerite and galena are very finely disseminated in the massive pyrite of the Meggen ore, and a very fine grinding combined with a special flotation technique are required to liberate the valuable sulfides and to produce separate concentrates of lead, zinc and pyrite. Mining is performed by the sub-level stoping method and employs trackless equipment. Present operations provide ore from the 600 meter level. Annual ore production is 870,000 metric tons.

Jan 1, 1972

By Ronald M. Hays

During the twentieth century the Mesabi Range in northeastern Minnesota has been the major source of iron ore for American steel mills. The Mesabi Range extends along an iron bearing outcrop known as the Biwabik formation. This outcrop is some 120 miles long and up to three miles wide. The formation is from 200 to 650 feet thick and dips 5 to 10 degrees to the southeast. The iron content of the original Biwabik formation was quite uniform, but much of this formation has been subjected to alteration. Thus major variations in iron content and mineral composition exist both laterally and vertically in the present Biwabik formation. The remaining unaltered iron formation includes the magnetic taconites which are commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons. per year of iron pellets and have produced approximately 170 million tons of pellets since 1956. Capacity for another 30 million tons per year of pellets is being considered by the industry for the next ten years. This increase will be obtained by construction of new plants and expansion of present operations. Thus by 1977, it is estimated that approximately 60 million tons per year of iron pellets will be produced from magnetic taconite on the Mesabi Range. The portions of the Biwabik formation subjected to intense alteration resulted in the direct shipping, wash and heavy media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron for American steel mills. In 1966, 12 million tons of direct shipping ore and 18 million tons of wash, jig, heavy media and other gravity concentrates were shipped from the Mesabi Range. These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from about 30 million tons in 1966 to 6 to 8 million tons in 1975. This decrease will be due to depletion of reserves and poor quality product.

Jan 1, 1968

By F. J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for those of us in the coal industry -particularly in Asia -the preponderance of the power plants being planned or under construction designed to use coal as the power plant fuel. This has produced a significant increase in the demand for steam coal, which has in turn encouraged many of us in the industry to develop new coal mines. One country that has enjoyed very substantial growth in coal production is Indonesia. This developing country of 195,000,000 people who live on the nearly 13,000 islands of Indonesia have emerged very quickly to become the third largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface mining methods. This paper will examine the surface mining of coal in Indonesia, as it continues to be an important part of the supply equation for coal in Asia.

Jan 1, 1996

By Brian E. Davies, Bobby G. Wixson

INTRODUCTION The mining, extraction and refining of metals into useful materials is an honorable profession with an ancient and productive history. Civilizations have long depended upon metals for their implements, structures and machinery necessary for survival, growth, and development. Today, as in the future, metals and minerals are essential to the progress of mankind as we approach the 21st century with technologies and concepts that will require new concepts and production from the metal mining and processing industries. Today is the tomorrow we talked about yesterday and the implementation of new ideas is essential if we are to achieve "Frontier Technology in Mineral Processing". Unfortunately, the state-of-the-art mining, processing, smelting and refining methods historically employed were less than desirable environmentally, which has caused todays public to view the metal mining and processing industry with concern. Presently the ancient rock and chat tips connected with old Roman lead-zinc mines which were worked in Wales are causing stream contamination problems that must be corrected at considerable expense to the local governmental agencies (Firth, J.N.M., et al., 1981). However, improved progress has been made and the environmental control and clean-up procedures utilized by modern lead-zinc operations in the "Viburnum Trend" or "New Lead Belt" of South East Missouri may serve as a model to illustrate how alternative technologies, environmental concerns and cooperative efforts contribute to efficient mineral production within the confines of a U.S. National Forest region without significant environmental impacts. This area received international attention when it was opened within the boundaries of the Clark National Forest in the mid 1960's. By 1970 it ranked first in the world by producing 432,576 short tons of lead ore and has since continued in this position producing 451,153 short tons of lead ore in 1983 representing 91% of the total United States lead production (U.S. Bureau of idines, 1983). This production comes from a mining area approximately 40 miles long by 10 miles wide extending in a north-south direction. Geologically the lead is disseminated throughout the Cambrain age Bonneterre Formation, mostly a dolomite, at depths ranging from 700 to 1200 ft. (213.4 to 365.8 m). Galena (lead) is the principal ore mined with lesser quantities of sphalerite (zinc), chaleopyrite (copper) and silver being recovered as economic co-products. This new mining development in one of Missouri is most scenic areas could have led to a classic confrontation between industries and environmentalists. Instead, through the cooperation of industries, governmental agencies and university researchers, the Ozark environment has been protected, and may serve as a model for future coexistence of the mineral industry with the environment. Cooperative Program Development As early as 1965 five new mines and two lead smelters were being prepared for production and environmental concern was an essential part of that planning. All the mining companies became acquainted with representatives of the various federal and state agencies and scientists from the University of Missouri-Rolla (UMR). During the next six years, St. Joe Minerals Corporation, American Metal Climax, Inc., Cominco American Incorporated, Ozark Lead Company (Kennecott) and American Smelting and Refining Company participated in cooperative research efforts. The companies also participated in information exchange meetings, the development of improved analytical methods and the utilization of research findings in the modification or construction of pollution-abatement facilities. Early on research was carried out to determine background values and to establish natural baselines of trace metals in the surrounding environment. The unusual topography and drainage pattern of the mining area were helpful since it was possible to establish control sites and test sites below individual mine-mill operations to study waste-water effects on the receiving streams. The location of the ‘New Lead Belt', mines, mills,

Jan 1, 1985

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972