Search Documents

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By D. D. Runnells

In order to establish meaningful remediation goals and monitoring programs in areas disturbed by mining, it is desirable to determine the natural metals concentrations that existed in the area prior to mining. At Iron Mountain, California, several natural sources exist for acid drainage and loading of metals to Slickrock and Boulder Creeks. This paper describes methods to determine the contribution of copper and zinc to groundwater and surface water from those sources, including natural gossan rock outcrops, mineralized bedrock, and colluvial materials. Methods used include evaluation of: 1) historical information, 2) literature values of unmined, mineralized areas, 3) analyses of water from monitoring wells, 4) leaching studies, 5) statistical analysis, 6) isotopic studies, and 7) identification of background by elimination of mining sources. Results from this natural background determination show that Boulder Creek and Slickrock Creek carried elevated concentrations and loads of copper and zinc prior to mining activities. With repeated rinsing of reclaimed and remediated mine materials by rainfall, there will be a diminishing contribution from residual waste rock and tailings at Iron Mountain, and natural background will become an increasingly larger proportion of the total load.

Jan 1, 1999

Experimentation was performed on the flotation of apatite and dolomite separately using anionic collectors in the presence of Mycobacterium phlei. Also, the flotation of mixtures of dolomite and apatite in the presence of anionic collectors and in the absence and presence of the bacterium were studied. It was found that M.phlei functions as a depressant for both minerals. However, it functions as a better depressant for dolomite than for apatite. Experimentation was extended to two different Florida dolomitic phosphate rocks. In this investigation a concentrate grade of less than 1.0% MgO was achieved.

Jan 1, 1997

By G. Bonifazi

The study of minero-petrographical characteristics and the subsequent textural and structural characterization of an ore mineral represents the first step of each industrial processing whose aim is the beneficiation of each valuable mineral phase present inside the ore. Analytical, mineralogical and petrographical, chemical and multispectral image analyses based investigations, applied to eclogitic ore samples deriving form "in situ" sampling campaigns, were applied. These procedures enabled to point out some textural and structural aspects characteristics of ore litotypes belonging to eclogitic-amphibolitic dikes. Such dikes are characterized by a paragenesis constituted mainly by siliceous gangue and accessory "useful titanium minerals" as rutile [TiO2], "pseudolilmenite", ilmenite [FeTiO3] and sphene [CaTiSiO5]. In the beneficiation process applied to ore s is of preliminary importance to establish a strategy in order to obtain a recovery of high quality "mono-minerals concentrates" as rutile, "pseudolimenite", ilmenite and phene. To reach this goal is thus necessary to develop a preliminary study of the textural, structural, petrochemical and minerochemical characteristics of the samples. Different ore samples (eclogitic rocks), resulting from sampling campaigns carried out in the Piampaludo area (Sassello district: Savona, Northern Italy), are examined.

Jan 1, 1994

By R. H. King

Suboleski and King (1990) analyzed the reasons for the dramatic increase in underground coal mine productivity during the last 10 years. This paper examines whether this increase can be extended. The paper forecasts whether the mix of technological, procedural and other factors that produced the increase will change in the future. The forecast is based on the base case and spreadsheet production model described in the previous paper.

Jan 1, 1991

By D. E. Healy

In 1989 an Autogenous Grinding Task Force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding at the National Steel Pellet Plant located in Keewatin, Minnesota. Pilot plant test work performed by the Hanna Research Center (HRC) indicated that fully autogenous grinding with pebble extraction and crushing could feasibly be incorporated into the existing circuits. In 1990, one of the existing ten grinding mills was converted for an in-plant test incorporating pebble crushing. The full scale test work conducted in 1990 and 1991 verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit utilizing pebble crushing being greater than throughput of the existing SAG mill circuits.

Jan 1, 1992

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

By J. R. Dyni

The lacustrine Green River Formation of Eocene age in the Green River Basin, southwest Wyoming, contains the world's large resource of natural sodium carbonate in bedded trona (Na2CO3? NaHCO3? 2H2O). In this study, 126 billion tons are estimated to be present in 22 beds, ranging from 4 to 36 feet in thickness. These 22 beds underlie areas of about 50 to more than 775 square miles at depths ranging from about 650 to more than 3,000 feet below the surface. The total resource of trona ore in the basin for which drilling information is available is estimated to be about 149 billion short tons. The undeveloped deeper trona beds in the southern part of the basin may be exploitable by solution mining. Additional unevaluated sodium carbonate resources are present in disseminated shortite in strata interbedded with the trona and in shallow sodium carbonate brines in the northeast part of the basin.

Jan 1, 1995

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By Michael A. Redfearn

The use of nitrogen in molybdenite flotation circuits is a relatively new concept utilized by only a few mines around the world. This paper briefly discusses circuit chemistry and the reason for its success. It follows the entire testing process which resulted in a sodium hydro-sulphide dosage reduction from 18.5 to 4.4 lbs/ ton (9250 to 2200 g/t) through to the final installation of an inert gas generator which will produce reagent savings in excess of one million dollars annually. A description of the various types of nitrogen generators commercially available is included.

Jan 1, 1983

By Atmesh K. Sinha

Death and injury rates in mining have been the highest of any industry; the injury severity rates in mines have also been the highest. Tentative figures reveal that 1971 was the best year yet for the bituminous coal indus¬try with the lowest number of fatal accidents. Nevertheless, 177 men were killed at a frequency rate of 0.76 per million man hours. Coal mine accident statistics have been described at various times as unacceptable and intolerable and recently resulted in the enactment of massive legislation. The 1969 Coal Mine Health and Safety Act was passed by Congress "to improve the working conditions and practices in coal mines and to prevent accidents and occupational diseases originating in the coal mining industry." The prevention of accidents in coal mines is the statutory responsibility of mining engineers and the moral responsibility of all who have any part to play in mining coal. The questions to be answered by these men may well be - What are the reasons for the high accident rate? Are the mines as safe as they can be? Are our mines sufficiently manned to insure proper supervision of production cycles and safety requirements? Are our plans for safety committees, safety campaigns, and safety inspections sufficient? Are they producing the results intended? If not, how can these be reorganized to have a greater impact? What is the real cost of an accident? What are the immediate and long-term plans for further improvements? These questions are in no way exhaustive, and the answers are not easy. There are many aspects of mine safety, and any one of them can be the subject of a lengthy discussion. The aim of this paper, therefore, is to limit the analysis to documented fatal electrical accidents in mines so that meaningful conclusions for improvement in electrical accident-experience statistics can be made. In doing this, it is also the intention to emphasize areas of missing information and propose a few suggestions for better hazard analysis.

Jan 1, 1972

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By Donald B. Buddecke

The large walking dragline has been the most commonly used overburden-stripping equipment in Texas lignite mines. These draglines, operating on the highwall side of the pit, can excavate to a depth of 45 m. Considerable overburden rehandling is required beyond 30 m and may reach 100 percent by 45m. As pit depth increases, dragline operation also becomes more complex, with two or three passes being necessary to make a cut 30 to 40 m wide. Multiseam operations also require extra passes. At pit depths greater than 45 m, the dragline must be operated also from a spoil bench. This can be difficult in the unstable alluvial deposits in which lignite occurs.

Jan 1, 1985