Search Documents

By Marco D. Boscardin, Paul A. Roy, Kevin J. DiRocco, Andy J. Miller

The North Shore Connector Project for the Port Authority of Allegheny County involves TBM mining a pair of subway tunnels through soil and rock under the Allegheny River and a narrow city street. Along the tunnel alignment are a historic building on shallow foundations and modern buildings on deep foundations, one constructed directly over the alignment during the latter phases of design. This paper provides an overview of the general site conditions, and technical basis for excavation support and tunneling decisions. Deformation limits, ground improvement, monitoring and mitigation plans, geotechnical baseline report development, and risk management will also be discussed.

Jan 1, 2007

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By D. M. Weinberg, S. R. Novascone, R. R. Reynolds, J. H. Cole, C. D. Christensen

The mechanical properties of the rocks surrounding an orbital vibrator alter the shape and amplitude of the vibrator’s orbit. Detecting these changes with driving point impedance measurements promises to reveal fractures and, possibly, identify the in situ stress state and significantly increase the depth that can be investigated. Our research emphasis has been on detecting vertical fractures through casing. Experimental and numerical results to date indicate that our new logging tool has excellent potential for determining both the vertical extent and azimuthal orientation of such fractures. Fracture and in situ stress orientations are useful in mine planning.

Jan 1, 2002

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By M. Ahrens

The paper describes the main drive systems of an iron ore pelletizing plant and related important design aspects. It is shown how today?s drive systems provide the desired flexibility for the process and lead to high energy efficiency and system reliability. With respect to electric drives expansion projects have many technical issues in common with green-field installations. However, there are aspects where important, distinct differences occur. It is shown which considerations for selecting and sizing drive systems for such a plant as well as for integrating them into an overall plant control concept need to be taken into account. Besides the design of the drive systems a key aspect for such an expansion project is the network interaction. Harmonics levels at different points in the plant network need to be checked carefully with simulations during the design phase to avoid problems later-on during operation. The power factor compensation and the harmonic filtering of the new production line cannot be designed independently of the already existing plant. The paper highlights areas where problems could occur and which points need to be paid attention to when a plant is expanded.

Jan 1, 2008

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

By Felix E. Mutschler

Alkaline rock-related precious metal deposits include: • orthomagmatic platinum group elements (PGE) ± gold (Au); • porphyry copper-silver-gold (Cu-Ag-Au, ±PGE); • epithermal Au-only, and Au-Ag-base metals; • submarine exhalative Kuroko-, Cyprus-, seamount- and Yellowjacket-type deposits; and • enigmatic deposits akin to Olympic Dam. Coeval epithermal deposits related to porphyry deposits suggest the two types represent separate immiscible fluids evolved in oxidized, CO2-rich alkaline magma chambers. Alkaline rock provinces develop above mantle hot-spots, but crustal structures control the final distribution of magmas and ore fluids. Prospecting guides for alkaline rock-related precious metal deposits include the presence of evolved alkaline rocks, pervasive K-metasomatic, redox and carbonatic alteration and low level Au (±Te, etc.) anomalies. Although alkaline igneous rocks crop out in less than 1 % of the area of the North American Cordillera and craton, alkaline rock-related ore deposits have produced nearly 13% of the total United States and Canadian lode gold production. Large (31-t or 1 million-oz) deposits are common (Fig. 1), and additional deposits and reserves are being discovered. New genetic models are evolving, making alkaline rock-related precious metal prospects attractive exploration targets.

Jan 1, 1991

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

By F. X. Spachtholz

"Raw materials industry is crucial for national economy. German mining companies are known for their high degree of resource efficiency based on modern technology and know how. K+S is one of the world’s leading suppliers of standard and specialty fertilizers. In the salt business, K+S, with sites in Europe as well as North and South America, is the world’s leading producer. The mine sites of K+S are distributed all over the world producing mainly potash and magnesium salts and rock salt. Focus is on the sustainable use of the natural deposits in order to stay competitive. For this reason a raw material policy, both national and international, is necessary to ensure access to new mineable deposits which are still available in Germany. Further on, knowing market conditions is a must for sustainable development. At least sustainability and resource efficiency in potash and rock salt mining are achieved by constantly developing new technologies as well as optimizing the organization and improving qualification of workers."

Jan 1, 2011

By Robert S. Shank

Introduction The Pinto Valley open-pit copper mine is located in southern Arizona, 11 km (7 miles) west of Miami. Production at Pinto Valley began in 1974. About 350 Mt (386 million st) of ore and waste was removed by the end of June 1982. At that time, the mine was using more than 90 major equipment items with a total mobile fleet numbering 320. Some of the major equipment consisted of four Marion M4 rotary drills; six P&H 15, 11.5- and 19.1-m3 (15- and 25-cu yd) shovels; and 24,136- and 154-t (150¬and 170-st) Wabco haulage trucks. This equipment was used to move more than 139 kt/d (154,000 stpd) of ore and waste. The mill was processing more than 50 kt/d (55,000 stpd) of mine ore. Shutdown A two-week vacation shutdown began in July 1982. Maintenance jobs were scheduled, and most employees left for the vacation. During the vacation period, copper prices fell below $1.32/kg ($0.60 per lb). Inventories remained at alarmingly high levels. At this point the mine was losing more money operating than it would by being shut down. The vacation shutdown was first extended to five weeks. But, after further evaluation, the mine was shut down indefinitely. In Dec. 1982, Cities Services Co., owner of Miami Operations (which included the Pinto Valley mine and mill), was acquired by the Occidental Petroleum Corp. On March 1, 1983, Occidental sold the operations to Newmont Mining Corp., and Newmont created Pinto Valley Copper Corp., as a wholly owned subsidiary. Copper continued to be produced by the Pinto Valley solvent extraction-electrowinning (SX- EW) plant because of its low cost per pound of production. To ensure proper equipment care during the shutdown, maintenance management was given three goals; • maintain the SX-EW plant; • maintain the environmental and pollution control systems such as domestic water pumps and mine dewatering; and

Jan 4, 1985

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

By D. L. Murr, J. R. Jensen

Testing was conducted on a Minnesota Iron Ore concentrate with Cook Clay as a binder using compressive sheer mixing to enhance the performance of the agglomeration mechanism. The testing was conducted on a bench scale at the Midland Research Center the summer of 2004. Results of the test program will be presented that shows the impact of compressive sheer mixing had on the strength achieve in a green ball.

Jan 1, 2006

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By A. A. El-Midany

Traditionally, the choice amongst different upgrading techniques or in finding the optimum operating conditions for a given upgrading technology depends on whether one is looking at the grade or the recovery of the valuable mineral in the concentrate. In fact, the conclusions are not usually the same. This is because the best technique or optimum operating conditions for the highest grade are not the same as the conditions to achieve the maxi-mum recovery. Therefore, a unique measure that takes into consideration both grade and recovery is urgently needed. Finding such a measure is the objective of this paper. A proposed measure provides a selectivity index in the range of 0 to 1, where 0 is no selectivity and 1 is ideal selectivity. The index can be obtained by plotting the so-called Fuerstenau upgrading curve, which relates the recoveries of the components in products of separation and a running regression applying a one-parameter equation. The measure was applied to assess the selectivity of selective flocculation under different operating conditions when used as a sensitive upgrading technique for ultrafine ground ores. After applying the proposed selectivity measure in the case of the selective flocculation of ultrafine Egyptian iron ore without the addition of cations, it was found that the optimum conditions are pH 11, 1 kg/t sodium silicate and 0.4 kg/t potato starch with a selectivity index of 0.55. With the addition of cations, the optimum conditions were found to be pH 11, 1 kg/t sodium silicate and 2 kg/t potato starch with a selectivity index of 0.65. It should be noted that determining these optimum conditions using the traditional grade or recovery measures was highly ambiguous.

Jan 1, 2008

By Mitchell L. Fong

The Bay Area Rapid Transit (BART) District will be extending BART service south along an 8.7-km (5.4-mile) -long corridor in the city of Fremont, California as part of the Warm Springs Extension (WSX). The WSX project will link the existing BART system to the future BART to San Jose extension. A segment of WSX is located in Fremont Central Park (referred to as the Fremont Central Park Subway Project). The Fremont Central Park Subway is considered the most complicated and geotechnically challenging portion of the project with an underground subway box being constructed near the active Hayward Fault which is capable of ground motions up to 0.75 g and is located in an aquifer which is used for water storage and supply. Soil-structure interaction analysis was used in the design of the subway box to resist deformations due to earthquake ground motions. A water-tight excavation support system has been designed to allow subway box construction while minimizing impacts to the aquifer.

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By P. A. Dimas

A new family of sulfide flotation collectors has been developed in our laboratory. These formulations are comprised of novel renewable materials combined with conventional reagents. The resulting diversity permits tunability of collector chemistry to meet a range of flotation problems. Several attributes of the new collectors are presented.

Jan 1, 2012

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004