Search Documents

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi Theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. The authors hypothesize that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, the authors hypothesized that the results of experiments conducted with the smaller scaled model should predict the draft on an upscaled model. The results show that the relationships between draft and longitudinal penetration and operating and dynamic parameters are similar for both scaled models. Similarly, the draft on the upscaled model, predicted by using the experimental results of the small model, is similar to the measured draft on the upscaled model. The mean difference between the two is 1.71 N with 95% confidence interval of [-3.51, 6.93], which is very good given the average draft is approximately 330 N. Thus, the work indicates that both hypotheses are true for draft. However, the work shows that scaling muck pile particle sizes using the Buckingham Pi Theorem is not adequate to ensure good predictions of penetration. This work provides insights that will help design engineers to acquire useful data on scaled models and use it for various analyses on heavy machinery.

Oct 6, 2021

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By Mohammed Sakr

The empirical relationship between torque measured during installation and pile capacity has gained a wide acceptance in the helical pile industry in the last few decades. This paper presents a theoretical model developed to estimate torsional resistance of cohesive soils to helical pile installation. The proposed torsional resistance model was then used to establish torque factor, Kt, a factor that is widely used in the industry. The results of the study indicated that the Kt factor is a function of the load path (i.e. tension or compression), pile geometry and soil properties. The assessed Kt factors in tension and compression were validated by the results of 74 installation records and full-scale helical pile load tests. A parametric study was also performed to qualitatively assess the relative importance of different parameters that affect the Kt factors.

Aug 1, 2013

By L. Harris

The gold mining and ore processing operations of Minera Yanacocha S.A. are 10cated in an area 4,000 meters above sea level in the Peruvian Andes same 600 km north of Lima and 20 km north of Cajamarca. The joint venture partners are Newmont Second Capital (USA); Compania Minera Condesa (Peril); Mine Or (France) and the IFC. Newmont manages the operation. The Yanacocha district comprises several areas with mineralization evidence. The first ore with minable reserves of 28 million tonnes of ore assaying about 1.4 gpt Au is called Carachugo and is being mined and treated at the rate of 14,000 tonnes of ore per day by open pit mining methods. ROM ore is dump leached and the gold recovered in a Merrill Crowe plant. The plant design incorporates some unusual considerations to overcome the problems of the high rainfall in this area and assure the protection of the environment.

Jan 1, 1994

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By Gy. Deák

The Romanian mining industry, especially salt mining, is going through a restructuring phase taking into account the Environment Acquis of the European Union1. In order to preserve the centuries-old salt mines and to develop new ones, in the same salt rock deposit, the long term stability assessment of the saline complex is very important. This case study refers to the Praid salt mine, which includes old salt mines, with impressive sizes, located above the new mines, with activity in progress, in order to provide the means and solutions for efficient conservation and sustainable exploitation for the salt resources. The DKRControl method and FLAC 3D code were used in order to assess the confidence level for the computed prediction of the stability of the salt mine complex salt.

Jan 1, 2008

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By J. H. Howard

The purposes of this report are to summarize the findings of the Committee on the Challenges of Modern Society Non-electrical Project (a working committee of the North Atlantic Treaty Organization) and also, thereby, to provide an introduction and review of the current situation regarding non-electrical applications to those who are interested in the subject.

Jan 1, 1975

By Yiming Zhang, Yunpeng Li, Chun Feng, Ruyang Cao

In the past, the selection of the number of empty holes between blast holes heavily relied on the subjective experience of practitioners, leading to unsatisfactory blasting results. The number of empty holes between blast holes is particularly important for the perforation of explosive cracks. In order to determine the optimum number of empty holes for inducing the propagation of explosive cracks, a two-dimensional numerical model of two-hole blasting was established based on the continuous-discontinuous element method (CDEM) using polymethyl methacrylate (PMMA) as the medium, and numerical simulation of various working conditions was conducted; the simulation results are basically consistent with the PMMA model test. Through the analysis of blasting parameters, the optimal number of empty holes with a certain hole spacing is fitted. The following conclusions are drawn: (1) There is a threshold for variable x. When x exceeds 50, the presence of empty holes cannot lead to the perforation of explosive cracks between the blast holes. (2) When x is below 50, the optimal number of empty holes inducing the propagation of explosive cracks can be determined through fitting an empirical formula. By adjusting the number of empty holes between blast holes, a significant spacing between adjacent blast holes was achieved, allowing for effective penetration, so as to effectively “induce” the direction of the fracture zone and make full use of the energy of explosives. The research results of this paper are conducive to the research of directional blasting technology and provide certain references for the optimization of precision blasting parameters.

Dec 19, 2023

By Yuanyuan Wang, XUEWEN WANG, Jinzhi Wei, Ligang Wen, Muxin Jia, Zhengyao Li

The abstract discusses the use of disodium carboxymethyl trithiocarbonate (D8) as an effective depressant in the flotation separation of stibnite and pyrite. The study investigates the mechanism behind D8's selective inhibition of pyrite, utilizing techniques like micro-flotation experiments, contact angle measurements, infrared spectroscopy, adsorption capacity analysis, and zeta potential measurements. The findings reveal that D8 physically adsorbs onto both pyrite and stibnite, but its adsorption capacity on pyrite is significantly higher. This adsorption enhances the hydrophilicity of the pyrite surface, hindering the adsorption of the collector and effectively depressing pyrite flotation, while having minimal impact on stibnite floatability.

Mar 14, 2022

By Rodolfo Lagos, Nicos Pfeiffer, Ben Harding, Clayton V. Deutsch

This paper documents a probabilistic resource modeling workflow for the Round Mountain epithermal gold deposit. The set of categorical and continuous variable simulated realizations provides a model of variability and uncertainty given the current orebody knowledge. These realizations can be used to quantify and understand expected deviations in reconciliation during mining and provide a more accurate measure of expected gold than an estimated model. Gold mineralization at Round Mountain is primarily contained within tertiary tuff units, which dip gently to the west and thicken towards the southern part of the orebody. Domain boundaries are modeled as combinations of lithology and alteration; alteration domains are constrained to be within the tuffs. Large-scale geologic uncertainty is strongly influenced by parameter uncertainty, particularly the input histogram. The spatial bootstrap characterizes prior global uncertainty in the input histogram for categorical and continuous variables. Categorical models are generated using hierarchical truncated pluri-Gaussian (HTPG) simulation. Continuous variable simulation is carried out within the simulated domain boundaries using trend models to account for non-stationarity.

Aug 19, 2023

By B. Barry, M. S. Klima

"Testing was conducted to evaluate the effects of hydroacoustic cavitation (HAC) treatment on two bituminous coal slurries and the subsequent separation of each slurry in a classifying hydrocyclone. HAC treatment was performed using a pilot-scale circuit fabricated by Furness-Newburge Inc. The circuit was designed to induce cavitation by means of flow through an ultrasonic resonator chamber or enhanced cavitation by initial flow through a cavitation chamber followed by flow through the ultrasonic chamber. The test materials were nominal -1,500-micron and -150-micron Illinois-basin bituminous coal slurries, which were obtained from an operating coal preparation facility. After 5 sec of HAC treatment, the median size of the -1,500-micron material was reduced, with ash values for certain size fractions decreasing more than 5 percent compared with untreated samples. Extending treatment time led to greater degradation of the +1,180-micron material and an increase in the -25-micron material, with ash reductions occurring for material in the -850+150-micron size range. Size degradation was less for the -150-micron material. Subsequent separation of the treated slurries was carried out in a hydrocyclone with diameter of 102 mm. HAC treatment led to a decrease in the ash value and an increase in the heating value of the underflow stream compared with the feed material. For example, the ash value was reduced by about 16 percent for the -1,500-micron material and 25 percent for the -150-micron material with heating value increases of 7 and 33 percent, respectively, after HAC treatment. Overall, HAC treatment appeared to have a slight effect on the size selectivity curves.IntroductionUltrasound in the range of 20 to 1,000 kHz, referred to as power ultrasound, consists of high energy waves that can create zones of compression and expansion when used to irradiate liquids (Frederick, 1965; Leighton, 1994; Mason and Lorimer, 1988). This action generates varying pressure regions leading to cavitation or the formation, growth and near-immediate collapse of microscopic voids or bubbles (Frederick 1965; Leighton 1994; Mason and Lorimer 1988). Collapse occurs when the bubble reaches critical size and cannot absorb additional sound field energy, and the critical size is governed by the ultrasound frequency (Shchukin et al., 2011)."

Jan 1, 2015

By Ewald H. Kurt

The story of America's progressing standard of living is the story of machines. The automobile, the airplane and the telephone for example have made our transportation and communication systems what they are today. Even they depend in turn on another machine -- the rock drill. By making it possible to economically mine and quarry minerals in large quantities, this versatile machine supports virtually every American industry relying on the earth for its buried raw materials. And, like all machines, the rock drill's mechanical evolution was stimulated by production demands placed upon it. All percussion drills are mechanized versions of the original drilling unit -- man, Figure - illustrates a double jack team at work before the turn of the century. The man with the sledge hammer is the impact device while the man sitting is the rotation mechanism and feed motor. The first drifter drills (Figure 2) performed the same function but with increased mechanical efficiency. A piston controlled by a valve produced impact. A built-in ratcheting mechanism provided rotation and a hand-cranked screw provided feed thrust. As the industrial revolution proceeded into the twentieth century, the demand for raw materials stimulated refinements of all recovery machinery, including rock drills. As drills became heavier and more powerful, a mounting (or carrier) had to be provided to move the drill from hole to hole. This resulted in the development of the wagon drill (Figure 3). Propelled by muscle power, the wagon drill was for years the standard tool of the surface drilling industry (Figure 4). As drills penetrated faster and as labor increased in cost, the time consumed in nondrilling peripheral operations had to be

Jan 1, 1977

By A. J. Plumpton

Centrifugal air classification and li-quid-phase sedimentation are the principal methods of industrially sizing materials of dimensions smaller than those handled by screens. Increasing application of materials such as composites and high performance ceramics has furthered the need for closely-sized, fine, industrial mineral and synthetic products of controlled properties. Sedimentation can be used to separate very small sized particles but introduces problems of liquid-solid separation, de-agglomeration and drying. Some of the advantages and limitations of centrifugal air classification will be discussed and laboratory and plant measurements using centrifugal machines will be presented to support the discussion.

Jan 1, 1990

By Eugie Kabwe

The effective employment of a pretensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut preload. In this paper, a load indicator washer (LIW) able to withstand an assigned static loading as well as provide an appropriate pretension is presented. The different LIW breadths are numerically analyzed with ABAQUS finite-element code to estimate deformation when a designated 60 kN preload is applied. The numerical simulation employs the bilinear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nut-LIW-rock bolt connection. Therefore, long-term relaxation effect on bolt pretension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW predetermined deformation is the bolt pretension. It is drawn from the simulation results that LIWs with thicknesses of 1.5, 2.0, 3.0, 3.5 and 4.0 mm are completely flattened when subjected to 28, 42.5, 65, 76 and 88 kN preloads, respectively.

By J. R. Evans

Mining claims must have a discovery of a valuable mineral deposit to be valid. When required, a Federal government mineral examiner makes a determination of validity and recommendations thereof to authorized management officials. The examiner should show whether or not an existing mining operation, or a proposed operation have economic viability. This is accomplished through an analysis of legal entities, land status and use, geologic and mineralogic relationships, and mining, milling and processing techniques considered in an appropriate economic evaluation framework. A framework involves market and market entry studies, reserve analyses, all costs analysis, royalty buyouts, tax structure, discount rate of return, and escalation and risk factors. An income approach to value is then used by means of a simple or complex discounted cash flow (DCF) analysis to certify validity. Whether one claim is owned by a single miner, or hundreds of claims are owned by a large corporation, thorough, fair, consistent, and appropriate economic concepts should be applied by the mineral examiner.

Jan 1, 1993