Search Documents

By S. Gaillard, E. Cauda

"Diesel particulate matter (DPM) is an occupational health hazard in underground mines. It generally occurs in the submicron range, and is often present in the mine atmosphere with significant concentrations of dust particles that tend to occur in the supramicron range. Since dust can interfere with analytical methods to measure DPM, it is often removed from a sample stream using impactor-type size selector (diesel particulate matter impactor, DPMI). Because the DPMI physically removes oversized particles from the stream, its performance may be gradually reduced with aging. Sharp-cut cyclones (SCCs) represent an alternative size selector for DPM sampling applications, with a major advantage being that, by design, they should not be susceptible to rapid aging. This paper presents results of a field study designed to compare the performance of aged versus new/clean DPMIs and SCCs in an underground mine. DPMI aging resulted in clogging of the device, and eventually a reduction of its effective particle cut size – though, when sample flow rate was maintained, DPM sample mass collection was not affected until significant aging had occurred. Under the conditions present for this study, effects of SCC aging were observed to be minimal by the end of the study period. INTRODUCTION Submicron particles are increasingly recognized as significant respiratory health hazards (Cantrell and Watts, 1997; Kenny, et al., 2000; Ristovski, et al., 2012). Diesel particulate matter (DPM) represents a major source of submicron particles in both public and occupational environments (Kittleson, 1998; Abdul-Khalek et al., 1998). Due to their work around large equipment in confined spaces, underground miners have some of the highest exposures to DPM (EPA, 2002; Grau et al., 2004). DPM largely consists of solid elemental carbon (EC), commonly known as “soot”, and organic carbon (OC) that may be sorbed to EC particles (Kittleson, 1998; Abdul-Khalek et al., 1998). EC and OC can be measured by thermal-optical methods such as the NIOSH 5040 Standard Method (Birch, 2016), and their sum is referred to as total carbon (TC). While the complex nature of DPM does not allow for its direct measurement, both TC and EC have been accepted as suitable surrogates for monitoring occupational exposures to DPM (Noll et al., 2007 and Birch, 2016)."

Jan 1, 2018

By Ping Li, Baokun Zhou, Lei Yang, Changfeng Li, Erhui Zhang

A uniaxial compression experiment was conducted on standard sandstone specimens to explore the sandstone’s mutation characteristics and early warning interval during deformation and failure. Meanwhile, acoustic emission (AE) and digital image correlation (DIC) techniques were introduced to realize multi-field analysis and cross-validation from the stress field, deformation field, and elastic wave field. The mutation characteristics of rock failure were investigated based on the cusp catastrophe theory. The results showed four mutation points in the destabilization process of sandstone: compressional density, yielding, destruction, and residual retention. As an internal activity characteristic of the sandstone failure process, AE directly reflected the dynamic failure process of sandstone. The stress variation was closely related to the evolution of AE characteristics. Sandstone loading failure was a process of the mutations of releasable elastic strain energy, dissipative energy, and releasable elastic strain energy. The mutation of dissipative energy was used as the starting mark of the sandstone warning state, and the second mutation of releasable elastic strain energy was used as the end mark of the sandstone warning state. Besides, the warning range corresponded to the loading time of 178 to 208 s. Finally, the sandstone instability warning interval was re-determined from deformation field evolution characteristics in the sandstone damage process, with a loading time of 180–204 s. This was consistent with the warning interval specified using the cusp catastrophe theory. The combination of AE, DIC, and cusp catastrophe theory revealed the mutation characteristics and early warning interval of sandstone failure. Hence, the results provide significant importance to predicting rock failure.

Aug 23, 2023

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By J. O. Marsden, C. Green

In 2003, a high-temperature pressure leaching circuit to treat copper sulfide concentrates was commissioned at the copper/molybdenum operation at Bagdad, AZ. In late 2007, a medium-temperature pressure leaching circuit was commissioned at the Morenci mine in Arizona. The Morenci circuit was shut down in mid-2008, following a fire in the autoclave circuit. The onset of the global financial crisis in late 2008 resulted in significant changes to the operating profile in the Southwestern United States with respect to concentrates production, concentrates treatment, acid production and acid consumption. As a result of these changes, the Morenci concentrator was shut down, and the pressure leaching circuit remained offline. In late 2014, the increasing acid requirements in the Southwestern United States prompted a reevaluation of the Morenci concentrate leaching facilities. As a result, the pressure leaching circuit was restarted in high-temperature (200 °C) mode in May 2015 and has operated successfully for three years since recommissioning. This paper describes the current pressure leaching circuit configuration and the factors leading to the successful application of copper sulfide concentrate leaching at this location.

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By Yongjun Peng, Yufan Mu

Pyrite depression in the flotation of copper ores is difficult due to the activation of Cu2+ ions on pyrite surface. In this study, the radical chain reaction involving the redox cycling of Cu(I/II) induced by sodium metabisulphite (MBS) was exploited to selectively depress the flotation of copper-activated pyrite at pH 8.0. Electrochemical measurements revealed that the presence of Cu2+ and O2 was essential to the formation of SO•− 5 through sulphite oxidation, the main entity to convert the activating species Cu(I)S on pyrite to Cu(II)-hydroxide/sulphate, causing deactivation of pyrite. The depression role ofMBS on pyrite flotation was closely associated with the type of grinding media which affected the electrochemical conditions of flotation. When forged steel was used as the grinding media, a high dosage of MBS was required to depress pyrite, but a low dosage of MBS could almost completely depressed pyrite when high chrome steel grinding media was used. This is because high chrome steel produced a stronger oxidation condition with a higher amount of Cu2+ and O2 which promoted the formation of SO•− 5

Jan 26, 2021

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By Dongjie Zhang, Fengyu Ren, Xudong Li, Yanjun Zhou, Yang Liu, Rongxing He, Jianli Cao

Based on the limiting-equilibrium analysis of roof processive caving in hanging wall caving method and the critical medium column theory, a new model of subsidence prediction caused by sublevel caving mining method was proposed in this study, considering the drawing influence and the dynamic process of filling granular media. Meanwhile, the distribution rules for lateral pressure with different orebody dip were studied under drawing ore, and subsequently complemented the model. This model indicated that the surface subsidence scope decreased as the unit weight of crack rock and the orebody dip increased. In addition, the height of critical medium column showed a decreasing trend as cohesion of rock mass, the internal friction angle and the unit weight of rock mass. Also, the method of predicting the scope of surface subsidence in the Dabeishan Iron Mine was applied. The results showed that the relative errors are less than 9% and the prediction method could be used in practical application.

Feb 24, 2022

By Zhibiao Guo, Jinglin You, Dongshan Yang, Yuanxin Zhao, Yuhui Li, Jingwei Gao

By utilizing collapsed gangue to create gob ribs, roof cutting and roadway maintenance (RCRM) technology enables coal pillar-free mining, presenting a novel approach. Due to their inherent structure, faults, which are common geological formations, can lead to various hazards, including fault sliding and significant deformation of roadways. In this study, a selfdesigned underground engineering simulation test device is utilized to imitate the cross-fault mining of the 11,101 working face in the Qipanjing Coal Mine (East). The objective is to examine the behavior of the surrounding rock and stress evolution. Generally, the experimental findings demonstrate that compared to the return air roadway, the RCRM roadway experiences a 3.3% decrease in maximum coal rib stress. This suggests that the implementation of this technique can effectively alleviate the stress on the surrounding rock of the roadway. The maximum coal rib stress, lateral pressure of the gob rib, and maximum deformation of the roof near the fault of the RCRM roadway are 11.3%, 25.6%, and 86.1% greater than those of the conventional geological conditions, respectively. The roadway deformation is negatively impacted by the fault structure. Based on experimental data and field measurements, a discrepancy in the maximum roof deformation between the test and field monitoring results under typical geological conditions is 8%. This indicates a favorable alignment between the test results and the real-life scenario. In conclusion, the proposed targeted control technique is implemented in the field by integrating the mining invariant equation and gangue volume expansion equation. This not only validates the effectiveness of the technology but also offers valuable insights for the future utilization of RCRM technology under comparable circumstances.

Feb 20, 2024

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By Jieliang Wang, Shiwen Yi, Zhao Cao, Peng Zu

Bayan Obo ore contains mainly bastnaesite, monazite and associated iron, fluorite, calcite, dolomite, barite, and trace amount of columbite. Due to its complex mineral compositions and similar mineral properties, it is difficult to separate and obtain rare earth and fluorite concentrates with high purity by conventional magnetic separation and flotation. In this paper, a stepwise magnetic separation process comprised of wet permanent magnetic separation (PMS), wet electromagnetic separation (EMS), and superconducting magnetic separation (SCMS) was proposed to pre-concentrate iron, rare earth, and fluorite minerals from Bayan Obo ore. The results showed that iron, rare earth, and fluorite preconcentrates with high purity and low impurity content could be achieved, which might be helpful to shorten the technological process and improve the separation efficiency for the subsequent flotation of iron, rare earth, and fluorite minerals.

Sep 15, 2020

By Wu Aixiang, Zhou Qian, Zhou Zaibo, Liu Juanhong, Wang Hongjiang

To improve the pumping capacity and engineering efficiency of fresh thickened tailings slurry, a high charge density superplasticizer was developed to improve the rheological properties of tailings slurry. The effects of superplasticizer content, the concentration and fineness of tailings, the proportion and type of cementitious materials, temperature, and hydration time on the rheological properties of unclassified tailings slurry and backfill materials were studied. The variation characteristics of the slurry yield stress, plastic viscosity, and thixotropy with different factors were measured by a Brookfield R/S-SST plus rheometer. The experimental results of fresh thickened tailings illustrated that the higher the concentration of the slurry and the finer the tailings, the worse the rheological properties of the slurry. The results of cemented paste backfill materials indicated that the rheological parameters increased as binder content and time increased. The rheological parameters decreased as the temperature increased. The addition of a superplasticizer reduced the rheological parameters and improved the rheological behavior of the fresh thickened tailings and cemented paste backfill materials, which was beneficial to the slurry’s pipeline transportation. This paper can provide technical guidance for slurry transportation in the backfill system and provide a reference for designing the superplasticizer used in tailings.

Jan 5, 2022

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021

By Ing. E. h. Martin Herrenknecht, Werner Burger

In recent years, there has been a dramatic increase in the number of machine driven soft ground tunnelling projects. This increase is largely due to the technological development of slurry and EPB Shield systems. A new generation of soft ground tunnelling machines, markedly different from those of five years ago, now overcomes ground conditions that until now were too costly and impractical to undertake. The paper reviews the latest soft ground tunnelling machine developments in material transport, guidance and control, seismic surveying, soil conditioning, settlement control, cutting tool applications and variable mode operating systems. Specific projects where this technology has been applied will be highlighted.

Jan 1, 1999

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau's coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964