Search Documents

By R. Y. Wan

Acid ferric sulfate solution has been used for heap and dump leaching of low-grade chalcopyrite ores and is being considered as a possible lixiviant for the hydrometallurgical processing of copper sulfide concentrates. For many years, researchers have attempted to explain the leaching behavior of chalcopyrite, since the reaction rate kinetics are extremely slow and seem to be significantly influenced by the nature of the reaction product. A summary of conclusions drawn from reported literature on chalcopyrite leaching is found in the paper by Munoz, Miller, and Wadsworth(1) and more recently by Dutrizac.(2) Lowe(3) and Jones and Peters (4) attributed rate control to a surface reaction. Linge,(5) Dutrizac,(6) Bauer,(7) and researchers at the University of Utah(1,8) reported that the reaction rate is limited by transport in the chalcopyrite lattice or through the elemental sulfur reaction product layer. Munoz et al.(1) presented a model, derived from the Wagner theory of oxidation, which is based on the formation of a protective sulfur layer with rate control by electron transport through the insulating sulfur layer. By utilizing Wagner's parabolic oxidation relationships, (9) the following equation was obtained: [ ] where a is the fraction of CuFeS2 reacted at time t, pB is the molar density of CuFeS2, do is the initial diameter of the particle, e is the electronic charge, s is the total electrical conductivity of the sulfur layer, and ?G is the Gibbs free energy for the reaction:

Jan 1, 1984

By Furuyama Takashi, Mori Sukeyuki, Hara Tsuyoshi, Fukushima Yujin

In mineral processing practice, flocculation is largely established as an engineering technique of waste water treatment and the study of parameters increasing the settling velocity of particles is still of great importance to improve the process. Further investigations were made using quartz (Q89) and fluorite samples (F91) which included 58.8% and 65.8% of -2.3 µm particles respectively. In all the experiments the flocculation phenomena were observed varying the pH value of the aqueous suspension. In contrast to quartz particles (Q89) which did not flocculate for all pH values, it was, noticed that fluorite particles (F91) flocculated in the alkaline range of pH over 11. With an aqueous suspension containing equal quantities of Q89 and F91, a hetero-flocculation of particles was observed at a range of pH below 10. In this case, the maximum floc size of the hetero-flocculation was 37.0-26.2 µm This size was about three times larger than when quartz (Q84) and fluorite particles (F85) were used with 32.4% and 40.4% of -2.31 µm particles respectively. Besides, in the experiments using Q89 and F91, the maximum size of hetero-flocculated single particles was found to be 6.54 µm instead of 3.27 µm as obtained with Q84 and F85.

Jan 1, 1995

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By Anuradha Khetwal, Sandeep Khetwal, Andrea Panciera

The observation method is a design optimization approach for the drill and blast method in tunneling. This method includes first identifying the hazard scenarios through site investigation, formulating suitable solutions, obtaining feedback during construction, and finally using that data to optimize the design methods. This paper illustrates the application of the observational method for T-48, a railway tunnel project in the Himalayas. It is a 10.2 km long tunnel with a parallel escape tunnel and 26 cross passages. The use of observational methods in this project optimized the overall tunnel design and considerably saved the overall project cost.

Jun 23, 2024

By W. D. Monaghan

One of the major ignition sources of fires and explosions in underground U.S. coal mines is flame cutting and welding. On May 20, 2006, a flame-cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On Jan. 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame-cutting and welding operation at the Loveridge Mine caused a fire that required sealing the mine for an extended period. On March 19, 1992, an explosion initiated by welding at the Blacksville No. 1 Mine resulted in four fatalities. These examples of mine incidents demonstrate the need to conduct research to develop best practices for safely conducting flame cutting and welding in underground coal mines. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame-cutting and welding operations to determine the root causes of these types of incidents. The methodology included interviewing mining personnel who perform flame-cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations. In addition, MSHA reports of investigations and accidents statistics were analyzed. The findings were used to identify and compare differences between flame-cutting and welding practices and techniques in small and large mines, eastern and western mines, low-seam and high-seam mines, room-and-pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices were developed to reduce the number of ?res and explosions caused by flame cutting and welding. This paper provides a summary of this research.

Jun 1, 2010

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The history of Duluth commences with Daniel de Greysolon du Lhut, one of the explorers of the Upper Mississippi who came to the head of the lakes in the summer of 1679. Radisson and Groseillier, and Claude Allouez, a Jesuit priest, are supposed to have visited the head of the lakes, -but there is no authentic record previous to that of du Lhut.In 1792, the fur traders established a fort at Fond du Lac, fifteen miles up the St. Louis River from Lake Superior, but within the limits of the present city •of Duluth. In the early 50's, there were a few scattering settlers at Oneota and around the George Stuntz trading post on Minnesota point. In 1855-6, the settlement on Minnesota point was called Duluth, commemorating the name du Lhut, and organized as a town in 1857. The first board of trustees and town council consisted of -William Nettleton, J. B. Culver; Robert E. Jefferson, Grin W. Rice and William Old: In 1870, the city of Duluth was incorporated, and five years later a portion of the same territory was incorporated as the village of Duluth, and the two municipal corporations were still in existence on March 1, 1887, when the city and the village of Duluth were incorporated as the present city.The first saw mill in Duluth was erected in 1856-57, on the present site of the ship canal. It cut logs from a virgin forest at the upper end of Minnesota point.The first railroad was built to the head of the lakes in 1870. The charter for this road had been granted in 1861 to the Lake Superior and Mississippi Railroad Company, afterward called the St. Paul and Duluth, and which is now a part of the Northern Pacific Railroad."

Jan 1, 1920

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

By X. Tang, N. Ripepi

The Langmuir model has been widely used for the coal-methane sorption process through an isothermal test. However, even though the temperature-dependent Langmuir model was recognized theoretically and experimentally, the quantitative relationships between the Langmuir constants a and b and temperature have not been clarified and confirmed by laboratory test data. This paper collects 158 methane-coal sorption data under different temperatures that apply the Langmuir model to the relationships between the Langmuir constants a and b and temperature. Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters a and b. The results from these published isothermal tests indicate that (1) there is no consistent relationship between Langmuir constant a and temperature, (2) the Langmuir model is a temperature-dependent model whose temperature-dependent feature is mainly shown by the relationship between the Langmuir constant b and temperature, and (3) the relationship between the Langmuir constant b and temperature can be described by both exponential and linear relationships with dried coal. This paper provides a database for the temperature-dependent Langmuir model that can be used for the reservoir simulation of coalbed methane reservoirs and for the coal seam degasification modeling of underground coal mines, considering the heating effects induced by geothermal and heat injection through factors such as hot water, hot steam and ultrasonics.

Jan 1, 2016

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By Louis M. Schlesinger, Michael J. Garska, Joel F. Hutwelker, James T. Jr. Tanner

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P205 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Variables examined included superficial air velocity, throughput (superficial feed velocity), frother type, frother dosage, and bias rate.

Jan 1, 1993

By Natalie White, Joel Asp, Allyz Kramer

"Minnesota has robust reclamation standards and have proven results in the taconite mining industry. Reclamation of overburden spoils, lean ore spoils and fine tailings from taconite production has generally been successful on the Iron Range, using a low input standard reclamation practice. Success at reestablishing vegetation on these landscapes is likely due to fairly favorable chemical and physical properties (e.g., few limitations due to acidic generating materials, metal toxicities and water and nutrient holding capacities). However, coarse tailings reclamation has proven more difficult, presumably due to lower nutrients and challenges with moisture holding capacities. Research efforts conducted since 1990 have struggled to develop a reclamation strategy for coarse tailings that meets the Minnesota Mineland Reclamation Rules, Chapter 6130. However, new breakthroughs in scram mining technologies are producing fine and coarse tailings that have not been encountered nor reclaimed in northern Minnesota. Scram mining in Minnesota is defined as those mining operations that produce natural iron ore concentrates. Innovative research is underway to investigate and determine successful reclamation strategies to reclaim scram mining tailings from these scram mining operations. The research program is conducted through collaboration with SEH, Prairie Restorations, Inc. (PRI) and Mining Resources, LLC with funding support from the Iron Range Resources and Rehabilitation Laurentian Vision Partnership minescapes grant program.The research program was divided into three phases:Phase I. Bench-scale testing to identify successful treatments to reclaim and restore scram tailings through evaluating surface soils amendments, viable seed mixes and plant germination, growth and densities. Phase I was completed in early 2015.Phase II. Field-scale pilot trial to test larger scale effectiveness of the treatments deemed successful in Phase I and test various vegetative assemblages and planting techniques focused on the unique challenges with scram tailing basins. Phase II was completed in late 2016 with a summary monitoring report.Phase III. Produce a technical report of results for the research undertaken in this study, as well as compile prior reclamation results used during previous Minnesota iron mining reclamation projects on tailings basin applications. Phase III was completed in 2017 with a summary monitoring report and recommendations."

Jan 2, 2018

By X. X. Jiang

An efficient recovery of finely divided magnetite particles of 400/500 mesh from a mixture of magnetite/silica particles has been investigated by imposing a delicate balance between centrifugal and surface tensional forces on these particles. The effect of centrifugal force, surface tensional force, density and size of particles on the overall metallurgical efficiency has been examined. A mathematical model based on a momentum balance on the particles at the liquid/liquid interface has been developed. The validity and limitations of the model are discussed in view of the experimental results obtained.

Jan 1, 1992

By O. B. Bucklen

The Coal Research Bureau of the School of Mines at West Virginia University, using a modified design of a Russian flotation device, was able to obtain a clean coal product containing 7.64 percent ash with 94 percent yield and 97 percent coal recovery. This favorable performance was obtained with the semi-pilot scale flotation cell operating as a simulated three stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient "operation on high density feed slurry, and absence of moving parts.

Jan 1, 1964

By Rihab Guellala

In Tunisia, the Paleocene-Eocene series has an important socio-economic interest. It contains profitable oil and water accumulations. Moreover, it encompasses phosphate reserves. The present study uses seismic reflection prospection and borehole data for the reconstitution of the Paleocene-Eocene deposit structure in the Jerid area (southwestern Tunisia), a crucial step for the phosphate exploitation. Firstly, lithostratigraphic correlations incorporating water and petroleum wells were established according to different directions for a tentative approximation of the Paleocene- Eocene deposit geometry by following their lateral evolution. To give more details, seismic reflection profiles were interpreted in the second step. The Paleocene-Eocene formations were associated with their corresponding reflectors on the closest seismic profile using the relation of time and depth in petroleum wells. Analysis of lithostratigraphic correlations shows notable variations in the Paleocene-Eocene series thickness and depth. Seismic profile interpretation explains these variations by highlighting different buried tectonic features. The results confrontation reveals that the phosphatic deposit geometry in the Jerid area is mainly influenced by the (1) emergence of the Saharan platform and the Chott northern chain since the Late Cretaceous, (2) syn-sedimentary normal activity of E-W and NE-SW faults during the Paleocene-Eocene epoch, (3) reverse-reactivation of these faults, and (4) major Tortonian folding phase. This study can enormously enhance the Jerid area socio-economic development by presenting useful findings that may orientate the phosphate exploration.

Aug 15, 2021

By J. H. Daniel

The reduction of accidents will play an ever increasing role in the mining of coal and hardrock ores as mining operations become more mechanized, the equipment becomes more costly and sophisticated, and as mineral production exploits deeper and more marginal coal and ore deposits. The most effective means to reduce accidents is through the design of mining systems and equipment. Results of safety research by the U.S. Department of the Interior, Bureau of Mines, to design safer coal extraction and haulage systems and to reduce electrical accidents are presented.

Jan 1, 1991

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961