Search Documents

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

A machine that improves safety during the cutting of boxholes (ore-passes) and travelways in underground mining operations has delivered impressive results in trials conducted at a South African platinum mine. The technology is a joint effort by Sandvik Mining and Construction and platinum mining company Lonmin. The ABH 1600 boxhole borer was built by Voest-Alpine Bergtechnik, Sandvik’s Austrian subsidiary. It was delivered to the Lonmin Eastern platinum mine in February 2005. There, it was deployed underground on the Number 8 Level (320 m or 1,050 ft below the surface) at the mine’s Newman incline shaft.

Jan 1, 2006

By W. M. Hart

Business Process Improvement (“BPI”) Change to Survive “It is not the strongest of species that survive, nor the most intelligent, but the one most responsive to change.” [Charles Darwin] “If you want to understand something, try to change it.” [Kurt Lewin, social scientist] Many companies have tried one or more process management initiatives. Each effort may help develop a culture that is more receptive to change. Executive Management needs to be unwavering in support of change with systems and structures, staffing, development of people, measures, with incentives and rewards. General Electric developed principles for quality change management that are necessary for effective, continuing Business Process Improvement (BPI). Change Acceleration Process (“CAP”) One of the tools General Electric developed has been used successfully by companies around the world in a wide variety of industries. This tool, named Change Acceleration Process (“CAP”), is designed to improve acceptance of change. Acceptance is the method by which the creative energies of the workforce can be fully tapped. Over time, every employee receives CAP training at least once, and in many instances three (3) or four (4) times, and will work on one or more High Performance Teams. Thus, BPI can achieve and maintain its goals. The CAP tool focuses on: • Leading Change • Creating a Shared Need • Shaping a Vision • Mobilizing Communication • Making Change Last • Monitoring Progress • Changing Systems and Structures

Jan 1, 2006

By D. Dunbar

Flooding of open pits now receives considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit lake deep waters can effectively eliminate oxidation of pit-wall sulphides. A state-of-the-art, coupled physical-geochemical pit lake model is used to verify that a cost-effective, environmentally responsible closure strategy for the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia is to adopt a controlled, two-stage infilling of the open pit upon cessation of operations. By filling the pit initially with highly saline waters from evaporation/infiltration basins and naturally saline deep groundwater, followed by capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within 1 to 2 years, followed by the rapid onset of sulphate reducing conditions in the bottom waters. Hydrogen sulphide produced by sulphate reduction will readily react with dissolved metals to form highly insoluble metal sulphides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental management strategies. The proposed plan allows for: 1) safe storage of saline evaporation basin waters; 2) the potential for passive treatment in anoxic bottom waters of ARD seepages from other mine site operations should they arise; and 3) a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2001

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By B. Swarbrick

Today’s mining occurs in a dynamic world of conflicting objectives. Mining companies have to look further than a traditional cash flow analysis to determine the potential value of developing a mine. In particular, proposals for new mine developments undergo rigorous scrutiny by a variety of stakeholders including regulators, NGO’s, and the local communities. From a business risk perspective, how mining companies address stakeholder concerns can have a dramatic impact on the success of the project. In today’s mining environment mining companies must continue to ‘walk the talk’ to stay in business, particularly during downturns in the business cycle. Falconbridge’s Raglan Mine is an example of a project that was successfully developed in a region that is sensitive from many perspectives, including environmental, socio economic, and regulatory. Close working relationships with local stakeholders along with strong environmental management systems are necessary elements of continued success for the project.

Jan 1, 2000

By James L. Poole

The gold and silver markets from the late 1960's to the present are reviewed and the outlook for these metals in the 1980's is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960's. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

By J. D. Miller, R. J. Smith

Earl C. Herkenhoff Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95 % of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978, "Separation of Bitumen from Dry Tar Sands," was the first blockbuter. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high solids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95°C (203°F) in a 0.3 m solution of sodium carbonate -about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: • What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? • Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60-62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands. Reply by R.J. Smith and J.D. Miller We, too, share Mr. Herkenhoff s enthusiasm for the mining of tar sands-heavy oil and continue the development of related processing technology. Specifically, it will be noted that by appropriate control of bitumen viscosity in the feed (probably the most important variable for successful separation) the recovery can be accomplished at low digestion temperature and low addition of alkali. A 91 t/d (100 stpd) pilot plant based on our technology is now being operated by Enercor in Salt Lake City (Hatfield, Oblad, and Miller, 1982). In these same pilot facilities, rougher concentrates containing more than 80% bitumen on a dry basis are being produced from Asphalt Ridge Feed. However, the processing of certain other tar sands results in incomplete digestion of bitumen/sand aggregates as discussed elsewhere (Miller and Misra, 1982). Such undigested aggregates are shown in Fig. 1. In this regard, it is intended that a recycle stream will be installed in the pilot plant to provide for redigestion of middling products. Further details regarding surface chemistry aspects of this tar sand technology have recently been published (Misra, Aguilar, and Miller, 1981). References Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Recovery of Bitumen from Oil Wet Tar Sands," Processing, Second International Conference on Heavy Crude and Tar Sands, Caracas, Venezuela, Feb. 7-17. Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Processing of Oil-Wet Tar Sands," Symposium, Rocky Mountain Fuel Society, Salt Lake City, Utah, Feb. 18-19. Miller, J.D. and Misra, M. 1982, "Hot Water Process Development for Utah Tar Sands," Fuel Processing Technology, Vol. 6, No. 1, April, pp. 27-49. Misra, M., Aguilar, R., and Miller, J.D., 1981, "Surface Chemistry Features in the Hot Water Processing of Utah Tar Sand, Proceedings, "Symposium of Separation Science and Technology for Energy Applications," Gatlinburg, Tennessee, May 5-8.

Jan 11, 1982

By C. Geier

Our national interests are best served by having well-trained first responders available for rapid response to emergency situations in underground mines. However, recent mine disasters have indicated that focused training on hazard recognition, decision making, leadership, and incident command center protocols needs to be incorporated into a comprehensive training plan for all personnel involved in a mine rescue. Currently, there are very few training opportunities for the mining professionals responsible for making the crucial decisions needed during a mine emergency. With recent technical advances, it is now feasible to use a computer-based simulator to train mine rescue personnel for mine emergencies in their mine or any other mine at a convenient location without interrupting normal mining operations. This simulated environment teaches underground search and rescue procedures, communications, and decision making based on real-time information and hazard recognition. Since 2010, the Colorado School of Mines (CSM) has offered computer simulated mine rescue training using an incident command center (ICC) directed towards enhancing decision making and communication skills. To support this training, CSM partnered with Rite Solutions, Inc. to modify, enhance, and create simulation software for mine rescue applications. The focus of this partnership is to modify existing simulation technology to address the unique nature of underground rescue operations, make it applicable to any underground operation, create generic scenarios, and develop customized computer simulations, including scenarios, for specific sites. Need The CSM mine rescue computer simulator helps mine rescue teams train for mine disasters where they would be deployed for the rescue and recovery of a mine. It provides additional, readily accessible opportunities to train without affecting mining operations. While the simulator lacks the physical demands of a rescue situation, it is very effective for teaching mine rescue procedures as rescuers seamlessly walk through the process and work out issues before going underground. The mine rescue simulator also introduces students to coordination through an ICC which stresses the use of effective communication and hones decision making skills. Most of the mine rescue teams participating in this study had never trained with an ICC controlling the actions of the mine rescue team making this an extremely valuable training opportunity. In addition, the mine rescue computer simulator allows instructors to modify mine rescue scenarios and tailor the scenarios to each team?s individual needs resulting in a more versatile training experience. The goal is to ensure that all teams receive the maximum benefit from each training session.

Feb 27, 2013

By Martin Stone

Industrialized countries, particularly the United States and the United Kingdom, remain at the forefront of international efforts to control the potential disruption from computer malfunctions caused by the date change from1999 to 2000 — widely known as the millennium bug or Y2K. Disruption is least likely in the developed world, including the United States, Canada, western Europe, Japan and Australasia. However, the picture is potentially different in developing countries where many mining companies operate. The less developed the country, the greater the chance of some form of Y2K-linked disruption.

Jan 1, 1999

By R. Adsero

The analysis of equipment trends in AUSIMM?s Revision of Monograph 19; Australasian Mining and Metallurgy Operating Practices (AMMOP) in the paper by Dight et al (in press) raised some interesting and in parts disturbing trends in the Open Cut Mining Industry. According to the US Bureau of Labour Statistics the US mining and petroleum industries? productivity is down by 12% since 2004 while the Australian Bureau of Statistics shows the productivity of the Australian mining industry is down by 34% since 2001. In terms of open cut equipment median output for draglines is down by 15% since 2003; electric rope shovels are down by 41% since 2003; hydraulic excavators are down by 39% since 2008; front end loaders are down by 39% since 2007 and trucks are down by 41% since 2006. Clearly the boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top 10% by annual output per unit of input) has declined but not by as much as the median (eg. shovels down by 8%, excavators down by 19% and FEL?s down by 5%). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one will be crucial to reversing the decline in open cut equipment performance.

Feb 27, 2013

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

By Kent von Maubeuge, Charles R. Landis

The global bentonite industry is a dynamic market balancing a range of end uses with an ever growing number of bentonite producers. In addition, markets in developed countries are elevating the level of detail and transparency for materials reporting in programs, such as the Registration, Evaluation, Authorization and restrictions of Chemicals (REACH) program in the European Union. Bentonite is impacted by programs of this nature. The majority of the bentonite products sold around the world are sodium bentonites. These sodium bentonites consist either of natural sodium bentonites, or naturally occurring bentonite dominated by divalent interlayer cations (Ca+2 andMg+2) subsequently exchanged with sodium cation. The latter variety is often called “sodium-activated“, or “soda-ash treated” bentonite. Once exchanged with sodium, these bentonites are often difficult to distinguish from natural sodium bentonites using common commercial testing protocols. Due to their similar colloidal and bulk chemical properties; the lack of test procedures designed specifically to identify this product feature; and the failure to completely or effectively explain their differences, sodium-activated bentonite is often considered to be identical to natural sodium bentonite in the industry. This article defines both general types of sodium bentonite and presents a technique that could serve the industry as a tool to confirm the variety of sodium bentonite in question. Specifically, geochemical properties such as carbon (C13/C12) and oxygen (O18/O16) isotopic ratios can distinguish activated, even slightly activated bentonites, from bentonites not introduced to additional sodium during manufacture.

Jan 1, 2004

By D. Gignac, P. A. Studemeister, H. Koza

Two epiclastic horizons in an Archean volcanic sequence host the gold occurrences on the Dunraine property near Wawa, Ontario, Canada. The Grace horizon of cherty and pelitic tuff strikes north-northwest and dips east. Native gold occurs with arsenopyrite in bedlike and podlike bodies of quartz lenses and stringers set in a pelitic matrix. The Parkhill horizon of lithic graywacke with associated flow-breccia strikes southwest and dips south. Native gold occurs with minor sulfides in similar bodies of quartz erratic within the Parkhill horizon. The auriferous bodies occupy paleotopographic channels and troughs within the two horizons. The former producers are the Parkhill mine with 1689 kg (54,300 oz) Au, Darwin mine with 473 kg (15,200 oz) Au, and Van Sickle mine with 48 kg (1536 oz) Au between 1902 and 1944. The gold occurrences are syndepositional with the host volcanic sediments laid during a pause in explosive volcanism. Fumaroles along steep gullies on the flank of a subaqueous volcanic center precipitated aprons of auriferous silica-sulfide mud. Downslope slumping resulted in exhalative debris flows; gold concentrated in flexures and depressions along stumpage channels. Renewed explosive volcanism covered the auriferous sediments with pyroclastic tuffs, arresting the slumping of in situ fumarolic deposits.

Jan 9, 1985

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By H. K. Lin, J. L. Oleson

The purpose of this study is to develop a mathematical model to describe the oxidation of cyanide with SO2as proposed in the Inco process. This research employed a direct method for measuring the change in cyanide concentration with respect to time as effected by varying concentrations of SO2, copper and pH. Developing this model may be applicable in determining optimum conditions in a process well known and used in the mining industry. It was determined that the reaction is first-order with respect to cyanide, SO2and [Cu+2].The reaction order is 0.15, or zeroth order with respect to [H+] at pH range from 8.0 to 9.5.The activation energy, Ea, is 21.6 kJ/mol. The overall rate equation, as determined through this study is: [ ]

Jan 1, 2004