Search Documents

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipexo® extractant, P,P'-di(2ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By D. Bernabe

The mine scheduling process defines a mining sequence across the life of the mine and stipulates the amount of ore, waste, and specific blocks to be mined each year so that the highest economic return can be obtained under a number of constraints. There are a number of mine scheduling software packages available. Each claims to be the best scheduler by maximizing Net Present Value (NPV) or by minimizing overall mining costs. These mine scheduling programs follow different procedures and scheduling philosophies based on either mathematical or heuristic principles. There was no study in which the mine production scheduling procedures applied by these packages were discussed and compared. This paper evaluates four open pit mine scheduling programs recently developed and compares them in order to determine if significant differences exist among them. The same input data, which consist of a 3-D block model, an economic set of parameters, and the initial surface topography for a operating copper mine in Southern Peru, was used to test each technique. The following programs were investigated with respect to their ability to optimize the NPV for the case study. 1) M821V1 Scheduler by Mintec; 2) NPV Scheduler by Earthworks; 3) Milawa Scheduler by Whittle Programming; and, 4) Fundamental Tree Scheduling Method (FTSM) developed at the Colorado School of Mines. The results from this case study demonstrate that the scheduling software packages, Mintec, Earthworks, and Whittle obtained similar NPV’s, while FTSM scheduler gave a six percent higher NPV than the other schedulers.

Jan 1, 2002

By M. Deal

Particle size analysis is a fundamental measurement utilized in the mining industry, especially in comminution, hydrometallurgy, and mineral processing. While sieves and cyclosizers are the standard methods used to determine particle size distributions, in recent years alternative instruments have been developed that claim to provide more rapid and equally reliable results. Newmont Metallurgical Services has implemented the use of two such instruments, along with traditional methods (sieves and a cyclosizer), on a daily basis. The Malvern Mastersizer 2000 laser analyzer is a wet sample system that can analyze particles in the size range 0.02µm to 2000µm, and the Horiba CAMSIZER® is a dry system that can analyze particles in the size range of 30µm to 30mm using digital image processing. A comparative analysis has been performed to determine the applicability of each particle sizing method in laboratory testing.

Jan 1, 2011

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By Jan L. Reichelderfer, Thomas L. Richardson

Completion of the H-3 Highway Tunnel Project was a critical element in opening this award winning project. The exploratory tunnel was completed as a maintenance tunnel and included difficult shafts extending into the main tunnel cross passages. The project also involved a major addition to the traffic operations center including a deep excavation in close proximity to the tunnel portal structures. The projects also included various completions and improvements to the main tunnels, such as paving, drainage, maintenance, and a variety of critical life-safety issues, such as radio systems, telephones, etc. The highway opened in December 1997.

Jan 1, 2001

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

Minera Escondida, located in the Antofagasta Region of northern Chile, is the world’s largest producer of copper as concentrate and SX-EW cathode. Projects to increase mill and flotation capacity began soon after start-up in 1990 to off-set decreasing copper grade. Subsequent projects had the objective to increase copper production through heap leach and SX-EW production and a second concentrator. The mine footprint concurrently expanded peripherally from the central high-grade enriched core of Escondida and then into the separate Escondida Norte deposit. Early in the mine life, metallurgical forecasting that was based on metallurgical composites of presumed ore types and historical plant production was adequate for operational planning, plant design, and project valuation. This approach became unreliable, however, as the increase in mine footprint was accompanied by an increased variability in key ore body characteristics such as hardness, copper-iron sulfide mineralogy, and sulfide liberation textures that were not reflected in the geological criteria used for ore type designation. The project study teams turned to small-scale physical and chemical tests to better characterize the spatial distribution of these key ore characteristics. Programs associated with capital growth projects were carried out through the mid-2000s to sample and construct a three-dimensional spatial model of hardness, copper sulfide mineralogy, and rougher flotation recovery from tests on 15-m drill core composites. Mathematical models were developed from the respective ore characteristic data to calculate throughput, flotation recovery, and concentrate copper grade. The spatial models were integrated with the concurrent mineral resource block model using standard geostatistical methods and the metallurgical process calculations were applied to the block estimates. The geometallurgical model, originally constructed on a project basis, is now managed by a dedicated team reporting to the manager of Geosciences & Resources Definition in the Escondida organization. The model has evolved with increasing complexity of the mine and processing plants and currently includes seven forecasting areas for three concentrators and four areas for two leach plants. Metallurgical forecasts of mill throughput, final flotation recovery, and concentrate copper grade still have the highest relevance to mine planning and optimization. Sample preparation, test procedures, and quality control methods are summarized for the ore characteristic tests important to these forecasts. Analytical results from recent annual sampling programs are presented for the hardness indices, rougher flotation recovery, and partial extraction copper analyses. Geostatistical analysis of the SAG mill hardness index is summarized as an example for the spatial estimation process. Mathematic models are presented for throughput (based on hardness indices), final flotation recovery (based on rougher recovery and plant calibration studies), and concentrate copper grade (based on sulfide mineralogy and empirical pyrite rejection studies).

Aug 31, 2023

As opposed to a prescriptive-based design, a performance-based fire-protection system design allows the system planner the flexibility in choosing specific method, materials and design tools to achieve a preset goal. A different approach in fire protection and a powerful addition to existing method, the system has been around for many years, and has gone through numerous improvements. Despite its popularity in the building industry, it has not been introduced to the mining industry yet. As mines get deeper, increases in size and complication, mine fire safety system will also become increasingly challenging, a new and proven system should be able to great potential to eradicate many of the problems that are either unsolvable or cost-prohibitive with the traditional method. With increasing globalization and international exchange with other major mining countries a common language/practice also make the performance-based design method a desirable feature in mine fire safety system. This paper will first define a performance-based system, step-by-step design methods, likely impacts on fire-protection practices and possible challenges in implementing the system in US underground mines.

Jan 1, 2011

Simulator technology has advanced to the point where the cost of mining equipment simulators is beginning to make commercial sense. Simulator-based evaluation allows operators or potential employees to be assessed in a pseudo-real environment under surface and underground mining conditions. Simulator training also allows operators to be exposed to emergency and advanced situations such as brake or steering failure or a tireblowout. ThoroughTec, of South Africa, provides simulator equipment to the mining industry. The company’s various packages of simulator products provide an unbiased evaluation score that removes human error from the assessment process. This same evaluation score is also presented at the end of normal training or refresher training sessions. In this way, the simulator helps eliminate bad habits and improve efficiencies.

Jan 1, 2003

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By Erich U. Petersen

Recognition of mineralogical and chemical zoning patterns associated with mineralization is an integral part of mineral exploration. Even though the origin of zoning may not always be known, zoning patterns as expressed by the systematic distribution of ore and gangue minerals, alteration or elemental assays (soil and rock geochemistry) have received much attention and are extremely useful in guiding exploration efforts toward locating economic mineralization. By contrast, the potential of using zoning information recorded in solid-solution minerals to address practical geological-engineering problems has received less attention. Solid-solution minerals can provide critical information for common problems faced in exploration, mine development and valuation. Mineral zoning information from solid-solution minerals can now be easily obtained because advances in electron microprobe instrumentation have made these instruments a most efficient, accurate, economical and practical tool for analysis of large numbers of samples. Now entire mines and districts can be studied in a timely and cost-effective manner as required by modern mineral exploration and mining practice. This article shows how knowledge of the composition of fahlore minerals can be used in addressing important problems in exploration, development and valuation. Situations are described in which drilling intersected "low grade zones" (Case one: Orcopampa, Peru, precious metal system) and where there was a need to determine the "lateral correlation of multiple ore intercepts" (Case two: Sheep Creek, Montana, sediment-hosted sulfide deposit).

Jan 1, 1992

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By C. C. Russelll, V. T. McLemore

The Metals Mining Sector of the Acid Drainage Technology Initiative (ADTI-MMS) addresses technical drainage-quality issues related to metal mining and related metallurgical operations, for future and active mines, as well as, for historical mines and mining districts. One of the first projects of ADTI-MMS is to develop a handbook describing the best sampling, monitoring, predicting, mitigating, and modeling of drainage from metal mines, pit lakes and related metallurgical facilities based upon current scientific and engineering practices. One of the important aspects of planning a new mine in today’s regulatory environment is the philosophy of designing a new or existing mine or expansion of operations for ultimate closure. The holistic philosophy taken in the ADTI-MMS handbook maintains that sampling and monitoring programs should be designed to take into account all aspects of the mine-life cycle. Data required for the closure of the operation are obtained throughout the mine-life cycle, from exploration through post-closure.

Jan 1, 2004

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.

By Frank P. Frandina

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. The project involves clearance improvements to twenty-eight tunnels, twenty-one of which require structural modification. With construction of the first Package of tunnels just underway at press time, this paper summarizes the program implementation from design through the initial stages of construction.

Jan 1, 2008

By Verya Nasri

The Silver Line Phase III Project is the final one mile underground segment of the new Bus Rapid Transit in downtown Boston. The project is expected to significantly reduce existing and anticipated traffic congestion. The twin one-lane tunnels and two station platforms will be built by NATM in Boston saturated soft clay, sand and till layers in proximity to several historical buildings, underpinning two existing cut and cover subway stations and several major utilities in densely built urban area. This paper presents the analysis and design of the NATM tunnels and stations detailing the excavation sequence and support system and various ground improvement and pre-support techniques used in the preliminary and final design of the project

By Will Foreman, Douglas D. McLearie, Edwin K. H. Tong, William H. Hansmire

Hong Kong’s Strategic Sewage Disposal Scheme (SSDS) Stage I involves the provision of a system of deep tunnels for transporting to a central treatment works wastewater collected from a number of catchments around Victoria Harbour. For the SSDS Stage I works, about 24 km of tunnels have been excavated in hard rock at depths ranging from about 80 to 150 m below Victoria Harbour and the surrounding heavily developed areas of Kowloon and Hong Kong. Five tunnel boring machines(TBMs) with diameters ranging from 3.2 m to 4.3 m were used to excavate the tunnels. Tunnel excavation has been completed and tunnel linings are in progress. Major tunnelling issues such as ground stabilisation and water control encountered in the project are summarised. An overview of one of the possible future tunnel systems that might be adopted in subsequent stages of SSDS is also presented.

Jan 1, 2001

By V. Rajaram

R.C. Rex, Jr. V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 9, 1986

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.