Search Documents

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015

By P. E. Hand

Coal is a complex heterogeneous commodity that can be mined in a number of ways and needs to be processed to a homogeneous quality that satisfies the customer?s requirements, while attempting to maximize revenues. Only a small proportion of coal is suitable for metallurgical use. Export coals cover a wide range of qualities and some coals can be used optimally in the raw state for energy production. Critical quality parameters vary and can be a combination of heat value, ash, volatiles, sulphur, phosphorus, sizing, amongst others. The level of beneficiation is generally dictated by the washability of the coal, mining contamination, and the target product quality. The steps in the coal chain covered in this paper comprise exploration, mining selections, production, the washing process, and product delivery. Many points of sampling are needed to maximize yield at the correct quality, and some of these will be described in the paper. Keywords coal chain, coal beneficiation, sampling.

Jan 1, 2014

Sishen Iron Ore Mine previously used only A-grade material (>60% Fe in situ value) from the pit for beneficiating in the DMS plant to a final product grade of 66% Fe in lump and 65% Fe fine ore. The B-grade (between 50% and 60% Fe) and C-grade material (between 35% and 50% Fe) were stockpiled separately, owing to the inability of the existing DMS plant to beneficiate material at densities higher than 3600 kg/m3. The ability to beneficiate the B-grade material at densities higher than 3600 kg/m3 was evaluated, and air-pulsed jigs were found to be techno-economically feasible and value maximizing. The beneficiation of B-grade material would add to the existing DMS production of 28 Mt/a, with no additional mining cost and only limited costs for the handling of waste and B-material. The objective of the Sishen Expansion Project (SEP), i.e. the jig plant, was to produce 10 Mt/a of saleable product with six modules to the set physical and chemical specifications by 2009. During the start of construction, it was decided to add another two jig modules to the plant to increase production to 13 Mt/a. During commissioning and ramp-up the shortcomings and advantages of the jigs were fully experienced and understood, resulting in many changes to optimize jigging performance..

Jan 1, 2014

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By J. D. Stone

This paper briefly reviews the adequacy of existing management theories and practices and the managerial proficiency or competency in the South African mining industry. The investigation revealed that existing management practices are totally inadequate to enable all employees on all the levels of the mining industry to achieve the results required from them, in all aspects, at all times. As a result, the South African mining industry is gradually losing its long standing reputation as a relative cheap, competitive, and reliable supplier of minerals to the local and global markets. According to some prominent management authors and theorists, an all-inclusive unified management theory does not exist at present. In this paper the authors summarize the main aspects of a newly developed comprehensive, practical, and integrated management method. It is believed that the application of this method would significantly improve the future performance and competitiveness of the South African mining industry

Jan 1, 2010

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By J. C. Ion, O. Isaksson, J. Stjernberg

Iron ore pellets are a preferred feedstock for ironmaking. One method used for pelletizing is the grate-kiln process, first established in 1960.During the past decade, the establishment of new grate-kiln plants has increased rapidly, especially in China, and new constructors of pellet plants have started to operate in the market. It is well known that the grate-kiln method yields a superior and more consistent pellet quality compared with the straight-grate process. However, certain issues exist with the grate-kiln plant, which are discussed here, together with proposed practical solutions.

Jan 1, 2015

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013

By M. D. G. Salamon

It has been noted in recent years that the pillars in some bord-and-pillar workings scale or spall. In due course this process may result in the collapse of the affected panels. This paper presents a methodology for assessing the long-term behaviour of such workings, employing a simple model of pillar deterioration by scaling. It is assumed that scaling causes a gradual reduction in pillar width, hence the safety factor of pillars reduces in time. It is also postulated that the process of scaling will be arrested if the coal rubble around the pillar reaches a critical height. The probability that the pillars will survive for a certain period of time, or indefinitely, can be estimated. This can be accomplished by using the log-normal distribution proposed by Salamon and Munro4todescribe the distribution of the apparent safety factor values at failure. If an estimate of the rate of scaling is known, it is also possible to quantify, using a Monte Carlo technique, the expected life of the pillars. The method also facilitates pillar design by specifying a probability of survival for a given number of years or, alternatively, for an indefinite period. Using the limited pool of available data, analyses show that the proposed model does not appear to be inconsistent with observed behaviour of pillars in the Vaal Basin. The crucial parameter is the rate of scaling. Back calculations from eleven cases suggest that the rate of spalling in the Vaal Basin is about 0.2 m/year. It is noteworthy that two further cases in the same area give significantly higher rates (0.85 m/year). Some underground observations in the Witbank area indicate considerably lower rates in the order of 0.02?0.04 m/year. Further areas for study are recommended. These include a study of old workings to determine the extent and rate of scaling in the various coal fields, an investigation into the possible relationship between scaling and the chemical composition of the coal. In addition, model studies will be required to assess the practical impact of the research findings.

Jan 1, 1998

By F. Essrich

A quantitative rockburst hazard assessment procedure was introduced on Elandsrand Gold Mine at the end of 1994. It is currently used to evaluate the seismicity-related risk in production areas on the mine. Six parameters related to seismicity, geology, mining layout, and production are rated and results are used as a planning tool on a regular basis. The applied assessment can be considered successful in that it promotes awareness of the seismic hazard and provides an opportunity to address seismicity-related mining problems. A comparison between high risk panels and those working areas with rockburst incidents showed that high hazard ratings reliably forecast the occurrence of larger events in the following month but they do not necessarily predict those working places with rockburst-related accidents. From this one may conclude that high levels of seismicity do not coincide with high rockburst rates.

Jan 1, 1997

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011

Comminution is a vital part of minerals extraction, and therefore of the South African economy. The high cost and throughput-limiting nature of comminution forms a strong motivation for research directed at improving the efficiency of the process. Building on a ten year background of fundamental charge motion research, a new formal UCT flotation and communication group has been formed. The group is also moving strongly into the field of milling circuit modelling and simulation, based on close links formed with the Julius Kruttschnitt Mineral Research Centre (JKMRC) of Australia, and an international collaborative research programme.

Jan 1, 1998

By A. A. Angelov

This paper presents a unique method of monitoring the effectiveness of the planning process as well as the execution of mine plans. The method primarily determines the degree of deviation from the original mine plans by comparing actual mined areas to initially planned mining areas. The performance of mining operations is also measured by comparing actual and planned tonnages for a particular period. Once the degree of deviation from mine plans has been established the cause/s of the deviation can be determined through a simple fault tree analysis. Accurate identification of the reasons of deviation can aid the mine in selecting possible methods to correct the deviation. It is, however, beyond the scope of this paper to discuss the methods employed in correcting such deviations, as each mining operation will have unique causes of plan deviation and methods of remedying them. Deviations from the plan greatly affect the yields obtainable, which in turn affects the life of mine, thus having negative economic and financial implications. Accordingly, this paper presents a project management method which aims to reduce risk by improving planning systems to ensure optimum overall extraction of coal reserves.

Jan 1, 2010

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

"In mechanized mining, poor equipment efficiency (availability, utilization, productivity, and quality) can endanger the success of the operation. This case study will show how an initiative to improve equipment performance developed into a comprehensive turnaround plan for the mine that placed it in the forefront of performance achievement.As part of a company-wide review process, poor overall equipment effectiveness (OEE) was identified as a major reason for the mine not achieving its targets. A project to improve the OEE identified eight improvement areas (elements) that contributed significantly to the poor performances. Measurement metrics were determined for these elements, followed by determination of baseline and target (improved) key performance indicators (KPIs). Cost savings associated with the improved efficiencies were calculated and tracked throughout the project. The mine team determined the specific actions required to achieve the target KPI in each element. These were individually developed and managed like mini-projectswith allocated responsibilities for delivery. The paper will indicate how this OEE improvement initiative triggered an improvement in almost all sections of the mine. Soon after launch, the initiative gathered momentum as the KPIs starting to improve. A visible tracking system exists at the mine and each employee can see the improvements and feel the success. The original eight elements were extended by five more, and the mini-projects grew as participants saw the success of the initiative.This paper concludes that through management and worker involvement, visible measurement and controls, and carefully chosen improvement elements, the mine was turned around. It is now achieving and exceeding its targets, and employee relations and motivation as well as safety have improved considerably. All of these achievements are reflected in the bottom line."

Jan 1, 2016