Search Documents

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008

By P. Wiesner, H. –M. Stonner

A brief account is given of the influence of sulphuric acid and chloride ions during the recovery of uranium by solvent extraction, followed by a discussion of the settling behaviour of dispersions and models to represent that behaviour. The paper ends with a description of various methods for the recovery of solvent, which is lost in the solvent-extraction process by entrainment and adsorption on solids and by dissolution.

Jan 1, 1982

ENERGY 73 The First International Energy Exhibition will be held in Brussels from 13th to 18th May, 1973. Vllth INTERNATIONAL CONGRESS ON CYBERNETICS This congress will be held in Namur, Belgium, from 10th to 15th September, 1973. GRADUATE SCHOOL OF BUSINESS ADMINISTRATION University of the Witwatersrand The Sixth Executive Development Programme is scheduled to take place from 2nd July to 24th August, 1973. IFAC SYMPOSIUM 1973 Second announcement ofthe International Symposium on AUTOMATIC CONTROL IN MINING MINERALS AND METAL PROCESSING to be held at the University of New South Wales, Sydney, Australia, from 13th to 17th August, 1973. MINERALS AND ENVIRONMENT The effect ofthe mineral industry on the environment and mineral resources The Institution of Mining and Metallurgy, with the co-operation of the Institute of Quarrying and the Institution of Mining Engineers, will hold a Symposium "Minerals and the environment" at the Institution of Electrical Engineers, Savoy Place, from 4th to 7th June, 1974. COLLOQUIUM ON SLlMES DAMS The South African Institute of Mining and Metallurgy have great pleasure in advising members that a two-day colloquium on slimes dams is bei ng arranged for the 14th and 15th November, 1973. INTERNATIONAL SOLVENT EXTRACTION CONFERENCE This conference will be held at Lyon from 8th to 14th September, 1974. Particulars may be obtained from the Secretary: Dr A. Naylor, British Nuclear Fuels Ltd., Windscale and Carder Works, Seascale, Cumberland CA20 IPG, United Kingdom. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to RIOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. Proceedings of the Tenth International Symposium on Application of Computer Methods in the Mineral Industry (APCOM) The Proceedings of the APCOM Symposium held in Johannesburg from April 9th to 14th, 1972, have now been published. Members of the Institute may buy the Proceedings at a special price of R12,50 as against the list price of R25,00 to non-members. Verrigtinge van die Tenth International Symposium on Application of Computer Methods in the Mineral Industry (APCOM) Die Verrigtinge van die APCOM Simposium, wat op April 9 tot 14, 1972, in Johannesburg gehou is, is gepubliseer. Lede van die Instituut kan die Verrigtinge teen 'n spesiale prys van R12,50 koop, in teenstelling met die prys van R25,00 vir nie-Iede.

By RT White

For a number of years the steel tube and pipe industry has worked on resolving problems of product quality. These have largely been resolved and new products have been developed to take advantage of new developments. To fully coordinate market acceptance guidance on use of galvanized piping was also required. This was largely achieved locally in 2004 with the publication by the SABS of ARP 060 - Guidance on the use and application of hot dip galvanized steel piping for the transportation of potable water in South Africa. Use of this document is not easy however and a need to have a simple computer model to assist the specifier was identified. Working with a major tube and pipe manufacturer this is now being developed and this paper will provide the background to the model?s development and its intended use. There is still a need for a partner Code of Practice on the performance of galvanized piping in buried conditions and the need for this will be highlighted together with current available information.

Jan 1, 2006

By I. du Plessis

The metallurgical response of a difficult to treat coal and an easy to treat coal orebody were investigated in terms of the coal yield and the coal quality in a basic coal recovery flowsheet. The purpose of this paper is to show trends and derive principles for the treatment of different coal types. This investigation entailed using the LIMN simulator to simulate the metallurgical response by varying the plant operational parameters. The controllable plant variables investigated were: ?Cyclone size ?Screen and hydro-cyclone cut points ?Medium cut density ?Feed particle size distribution.

Jan 1, 2010

By B. C. Alberts

This. paper indicates how the South African Iron and Steel Industrial Corporation Limited (Iscor), as a major consumer of raw materials, determines the tonnage and quality of essential raw materials required to satisfy an increasing demand for steel and how this led to the establishment of a coal mine with a highly sophisticated beneficiation plant in the Waterberg coalfield, near Ellisras in the Transvaal. The planning of the project, with specific reference to the limited reserves of metallurgical coal in South Africa, the quality and quantity of the coal to be produced, and the way in which the project was managed is discussed briefly.

Jan 1, 1982

By W. A. Hodgson

"In order to be able to map the variation in the concentration of elements in soils, it is necessary to sample at intervals that will give adequate coverage of the area and will allow determination of the rate of fluctuation of concentration with distance in any environment. This rate of fluctuation with distance can be referred to as the continuity of concentration.The continuity of concentration in soils varies according to the chemical characteristics of the element being considered, the underlying rock type or orebody and in response to the dispersion processes that operated during soil formation. Within any environment there is a maximum distance between sampling points within which adjacent sample values are related. This distance, the critical sampling interval, can be determined by means of a correlograrm.Where the sampling grid has been chosen to provide an adequate coverage over unmineralized rock, adjacent samples being related, anomalies may be missed if the element continuity in the anomaly is less than in the background. Results show that a knowledge of the critical sampling interval of the environment being examined may used to select a more efficient sampling pattern for a geochemical survey."

Jan 1, 2014

By G. S. Bartlett

The theme of this Colloquium, survival strategies, not only conveys a sense of urgency but also takes cognizance of the fact that, as in the political arena, tough decisions have to be made and acted upon in the years to come. It is therefore appropriate that the SAIMM, as spokesman for the metallurgical industry, should be dealing with these issues at this time, and I wish to commend the organizers of this Colloquium for focusing on a mater as important as the future of this great industry. In view of this, I regard it as an honour and privilege to officiate on this occasion, where the best of South Africa's brain power in the metallurgical field will be harnessed with a view to moulding strategies for survival.

Jan 1, 1993

INTRODUCTION The SAIMM publishes technical information on various aspects of the minerals industry through several different media. (a) Monograph Series Books in the Monograph Series are high quality, detailed discussions on specialized topics. (b) Symposium Series This series consists of the proceedings of international conferences which are held in South Africa. (c) Special Publications Series This series covers titles which do not form part of the Monograph and Symposium Series. (d) The SAIMM Journal Papers published in the Journal cover al relevant areas of technical interest by striving for a balanced content and maintaining a consistently high technical standard. (e) School and Colloquia Notes The papers from al local schools and colloquia are published and handed out at registration. Should authors wish to have their papers considered for publication in the Journal, they should adhere to the guidelines outlined below.

Jan 1, 1991

By R. Guest

Reichert cone concentrators are used successfully in many applications, but have as yet not found favour in the gold mining industry on the Witwatersrand, because, for optimum operation, the cones need to have specially designed feed-preparation and circuit details. In addition, good liberation of the valuable minerals is essential. Gravity tests, in which a pilot plant was used on refractory gold ore, showed that 94 per cent of the gold could be extracted after gravity concentration and preferential grinding, roasting, and cyanidation of the concentrate, whereas 96 per cent could be extracted by flotation followed by the same preferential treatment. However, the capital and operating costs for gravity separation are expected to be considerably lower than those for flotation.

Jan 1, 1982

By D. J. van Niekerk

Caring for the Earth: South Africa-A strategy sustainable living, by John Yeld. Southern Foundation in partnership with the World Union. Soft cover. Tel.: (02231) 72801.

Jan 1, 1993

The winners of the Delfos and Atlas Copco Travel Grant for Mining Engineers were announced at a cocktail party hosted by Mr Mario Pellegrino, Managing Director of Delfos and Atlas Copco, at the Sandton Sun Hotel on Friday evening, 18th May, 1984.

Jan 1, 1984

By R. H. English, N. C. Joughin

The results of trials with three stope-face cleaning systems are described. Two of these systems were based on armoured chain conveyors, and the third on a reciprocating-flight conveyor. The operational elements of each system are discussed with reference to their effectiveness, and many problems are highlighted. It is concluded that the reciprocating-flight conveyor is superior, and has the potential for being developed into a system yielding a labour productivity of more than 30 m2 per worker per month and a face advance of 15 m per month working one shift a day.

Jan 1, 1979

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By Piotr M. Kapias

Keywords: extraction, lead refining, Pb-Tl solutions, PbCl2-TlCl solutions. The theoretical part of the paper presents an analysis of the conditions of Tl extraction from Pb using different extractants and determines the activity coefficients in liquid solutions of Pb-Tl and PbCl2-TlCl. The dependence of the solution activity coefficients upon the composition and temperature is presented in the form of Krupkowski and Krupkowski-Fitzner equations. An analysis and evaluation were made of the influence of the methods of PbCl2 introduction into a Pb-Tl solution upon the efficiency of the Tl extraction process under thermodynamic equilibrium conditions. The analysis made it possible to formulate relevant equations describing the dynamics of the process of Tl extraction from Pb under stirring conditions as well as under the extractant injection into the liquid Pb-Tl solution conditions. In the part concerning experimental work, results are given for tests on the Tl extraction process from Pb-Tl liquid solutions of initial Tl content of approximately 0.05% mass using PbCl2 or, alternatively, Cl2(g) conducted in laboratorial scale. The tests made it possible to establish the influence of time, temperature, mass and the method of introducing the extractants into the liquid upon the level of Tl extraction from a Pb-Tl solution. Labels used in the text. WT1m - TI content in metallic phase, % mass WT1s - TI content in chloride phase, % mass wpTlm - TI content in metallic phase in initial state, % mass W°Tlm - TI content in metallic phase in equilibrium conditions, % mass m°m - initial mass in metallic phase mm - mass in metallic phase mPbC12 - lead chloride mass fed to the system MPbC12-TIC1 - mass in chloride phase MPb - lead atomic mass, g/mole MT1 - thallium atomic mass, g/mole K - Nernst distribution coefficient Xi - mole friction of solution component X°PbC12 - mole friction of PbC12 in saturated solution X°T1C1 - mole friction of T1C1 in saturated solution T - temperature, K R - gas constant, J/(mole K) k - kinetic equation constant, 1/(%-min.) ?i - solution component activity coefficient e - extraction rate, %

Jan 1, 2008

By Gordon Chunnett, Ron Sheets, David Grant

[Power-Point Presentation]

Jan 1, 2005

By D. Rankin, H. J. Stucke, W. K. B. Loftus

Discussion: H. J. Wright (Member): The authors are to be congratulated on presenting such a comprehensive and lucid account of bringing a large diamond mine into efficient production from the grass roots. When one considers the vast amount of planning and hard work that had to be put into the project the authors have done a praiseworthy job in condensing the story, so as to present all the important technical aspects, the logic behind the major decisions and the future thinking on the operations, in a concise and readable form. This was the first experience of De Beers personnel in starting a large diamond mine as an opencast project and nor do they employ a large planning staff, most of the planning being carried out by the executive staff themselves. It is operating most efficiently on a large tonnage and it is neatly and very well laid out. In fact, with its model townships, both for European and Coloured employees, tarred roads, recreation club and its grass golf course, it is like an oasis in the arid climate of the North-Western Cape. The key operation of opencast mining is, of course, the planning of the geometry of the pit. This has been adequately dealt with by the authors. It is of interest to consider some of the consequences arising from complete lack of open pit planning, based on actual operating mines. I refer of course to the present, four producing mines in Kimberley. The Kimberlite pipes were all discovered in a short span of time from the year 1870, onwards. They soon became a hive of activity with diggers industriously working their claims at varying rates. The country rock comprises from the surface downwards, some 90 ft of decomposed dolerite followed by approximately 260 ft of soft Karroo shales, which in turn is underlain by a hard competent Ventersdorp lava, known locally as melaphyre. The average water table was just below the dolerite at a depth of approximately 90 to 100 ft. Only the blue ground was mined leaving the waste rock sides almost vertical, and as the depth increased beyond 100 ft, large falls of sidewall started to take place. The shale was unstable and the falls covered

Jan 3, 1969

By J. N. Van der Merwe

The South African coal-mining industry uses a uniform safety-factor formula for non-squat pillars, incorporating a coal-strength constant that was derived empirically by Salamon and Munro in the 1960s. The constant is 7,2 MPa. Since that time, collapses of pillars at relatively high safety factors have occurred in the Vaal Basin. Analysis of the post-1960s' collapses indicated that the strength constant for the Vaal Basin is 4,5 MPa. A crude method for the prediction of the minimum life span of pillars in the Vaal Basin is presented.

Jan 1, 1993

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis, including a brief statement of conclusions. Index, only if paper is long and involved. Introduction. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors &, Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler. H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory \matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol %is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.L) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramms metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, n, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and there. fore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .' . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there IS full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis, including a brief statement of conclusions. Index, only if paper is long and involved. Introduction. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol %is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramms metre per second per second (kg m/s'). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. I, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standardsymbols as laid down in British Standard 1219C shoulrl be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute.