Search Documents

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By Fun-Den Wang

Finite-element structural analyses were performed to determine the stress distribution and displacements around a single rectangular coal mine opening in a multilayered rock system. The effects of changes in mechanical properties of roof and coal layers, roof layer and mine opening geometry, horizontal-to-vertical load ratio, and structural geologic features on the stress distribution about the opening were studied. Variability in the stiffness and relative thickness of the immediate roof layers can produce a considerable difference in the stress distribution about the opening as compared with that of a homogeneous material. Changes in opening width and horizontal-to-vertical load ratio have different effects on the stress distribution about the opening depending on the composition of the roof layers. In general, where a stiff layer exists in the roof at the surface of the opening, the stresses are higher in the roof and ribs around the opening. Horizontal changes in facies in the roof layers produced by structural geologic features can also greatly alter the stress distribution about the opening compared with the simple layered cases.

Jan 1, 1974

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By R. E. Mussler

Electrowinning of copper from chloride solutions in a diaphragm cell was studied by the Bureau of Mines. The copper powder product was shaken periodically from the cathode and removed from the bottom of the cell. The effects of copper concentration, brine concentration, copper chloride species, and cell voltage were investigated. Power consumption of 1.1 and 2.1 kW-hr/kg were obtained with cuprous and cupric chloride solutions, respectively.

Jan 1, 1975

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By T. M. Kohler, G. L. Finfinger, D. M. Hyman, A. T. Iannacchione

The Bureau of Mines measured methane emission rates from an advancing salt face ranging from 15 to 56 ft3/ton (0.5 to 1.8 m3/t). Small room size, use of a continuous miner, and a well-defined ventilation system made possible air velocity and methane concentration measurements, These measurements, representing data from 18 production days, were con- ducted in an area of abnormally low grade salt, Methane emissions occurred primarily during the advance of the salt face by continuous miner.

Jan 1, 1982

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982

By G. W. Murrie, W. P. Diamond, S. W. Lambert

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high- through medium- to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By R. B. Tippin

Research investigations conducted on five ore samples show the applicability of heavy liquid separation (HLS) techniques to mineral processing. Under proper operating conditions, semicontinuous tests in small fluid cyclones yielded 90 percent sink-float concentrates with recoveries exceeding 90 percent on minus 35-mesh ore samples of kyanite, potash, spodumene, fluorspar, and beryl. Although none of the ores were examined in detail, their response to this novel concentration method provides basic examples that are typical of the process. Various aspects of cyclone design and operational characteristics of heavy liquid cyclone circuits were studied which demonstrated the flexibility of HLS by using multiple units connected in series. A comparison of two heavy liquid solutions, tetrabromoethane and methylene bromide, exhibited their individual advantages and limitations. Unique problems relative to this process are discussed including liquid viscosity, mineral composition of the ore, toxicity, and material handling hazards.

Jan 1, 1968

By d&apos, Kathleen J. Amico

THIS summary appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S mineral production also is included.

Jan 1, 1964

By Joseph E. Matta

The Bureau of Mines conducted tests using a tracer-gas technique to measure the effectiveness of the jet fan, which is often employed in mines to ventilate dead headings. Results of these tests show that jet fans can (1) ventilate dead headings beyond the maximum penetration distance indicated by smoke-tube detection of air movement, and (2) redistribute available fresh air through larger working areas. However, if the fresh air base is insufficient, the fan will merely recirculate the contaminated air and disperse it over a larger volume.

Jan 1, 1978

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

By Oliver Bowles

[In an endeavor to promote greater efficiency in the lime industry, the United States Bureau of Mines is preparing a series of preliminary reports dealing with particular problems of the industry. Through the circulation of these reports, it is hoped that sufficient interest may develop among lime-plant operators to prompt them to discuss with the bureau their our experiences with these problems. By such an interchange of ideas, it is believed that conclusion may be reached which will be of practical benefit to try entire industry. The first report, "Stripping problems it Limestone quarries of the Shenondoah Valley", Serial No. 2401, was issued during October, 1922. This report t is the second of the series. It is hoped that may operators will contribute additions to the information now at hand.]

Jan 1, 1922

By N. A. C. Smith

One of the most important considerations in any manufacturing industry is the production of stable material, that is, material which will not change in quality before it reaches the consumer. The manufacturer of gasoline, the refiner of crude petroleum, is handicapped in this respect by the varying nature of his raw material, but as far as it is commercially practicable, he has endeavored to improve his product, and in most cases he has been eminently successful. It sometimes happens, however, that a gasoline that is apparently normal when first made, will In time deposit small quantities of a gummy substance. The present Investigation was undertaken in the hope that it would throw some light on these gums and indicate how their formation might be prevented.

Jan 1, 1922

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC-formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed on to both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events. This is the first of two articles which report the responses that these experts gave when asked how they think people who may have to respond to a future mine emergency should be trained. During the interviews they discussed how training should be conducted, who should be trained, and what topics should be included. This article will cover the first two areas: what training methodologies would be most effective and who needs to participate.

Jan 1, 1997

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By Jerry L. Huiatt

An accurate and reproducible procedure was developed using the gas-liquid chromatograph to quantitatively measure oleic acid on flotation products and in flotation water phases. The method comprised extraction of the oleic acid from the mineral surfaces with alcoholic NaOH, esterification of the extracted oleate, and chromatography of the methyl ester with an internal standard. Quantitative analysis of oleic acid on flotation products from test tube and bench-scale flotation tests with pure minerals and with natural ores proved the applicability of the method on a variety of minerals. The accountability of oleic acid added was 100 percent, ±5 percent.

Jan 1, 1968