Search Documents

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

By E. H. Denny

"Reduction of mine accidents appears to depend upon essentially the same fundamentals, whether considered from the viewpoint of the mine operator, miner, State mine inspector, or safety engineer. Conditions of mine operation with respect to safety are governed in most States by a mining law, usually somewhat general in its provisions but more specific than laws dealing with other industries, Methods of mining development and practice evolved through experience have been handed down from generation to generation; many of these are intended to avoid injury to men and also loss of property. To carry out the intent of these bases of law and experience relating to safety supplemental measures and conditions are necessary. Among these may be: (1) Planned safety rules adapted to the mine and compliance by both officials and Miners with such of these rules as pertain to their work; (2) a supervisory force adequate and competent to ¬administer the mining laws and safety rules; (3) discipline adequate to secure compliance with safety measures; (4) safeguards against mechanical, electrical, falling, and other hazards; (5) mining operations planned with respect to safety of workers; (6) an active safety organization of officials and employees; (7) education of officials and employees in safety practices; and (8) an active sustained interest in safety by management and employees.This paper presents the viewpoint of the safety engineer, though a safety engineer connected with a specific mine or group of mines would be in a better position than the writer to present the industrial engineer's thought. The application of the mine safety fundamentals just outlined will be given consideration from observations of methods used by safety engineers and supervisors.The term ""safety engineer"" includes men of various duties, various degrees of experience, and various authority. Depending upon the size of the operation or the interest of the management in safety, the safety engineer may have accident prevention as his sole duty; he may be the head of a sizable safety organization; or he may be in part a claim agent; a statistician compiling figures for the enlightenment of the company, the public, or a mining institute meeting; a surveyor who must convince the miner that his scale of 10/10 equals 1 foot does not defraud the miner of 6 inches to every yard measured; or he may be by heaven¬ly gift an orator capable of assuring the employees that ""all's right with the world""; he may be a young engineer gaining, experience while checking the observance of company rules and investigating accidents; or he may have the physical ills frequently resulting from several decades of mining experience and instead of a pension, the position of safety engineer has fallen to his lot. He may have mine-operating authority to correct immediately a dangerous condition or practice or he may have his recommendations officially disregarded at the monthly meeting or when the bottom of the desk basket is reached. He is likely to find that his viewpoint on accident reduction is considered unsound today because of youth and inexperience and unsound later because of old age and senility. He is likely to find the easiest course to be that of attributing to Providence and the carelessness of the worker the mishaps that result in the removal of a man to the hospital or the morgue."

Dec 1, 1936

By Raymond B. Ladoo

Cne of t·: . .:: i::,portt recent developrr.ents in the feldspar industcy l:.a.s beer. tl:.e r,:ipid. rise of Ne·N H.v-:psr.ire as a. feldspar producing State. Tl:.e unusual size and purity of t: e deposit now 'being worked ne3.r Keene, and tr.a i.nproved metl:.ods ot:' rr.ining srd ir,illing used l:.ave been responsible foe tt.is situation. ti'eldsp'.:l. w'ls occ':tsiona.lly produced sorr.e ye1rs ago in srr.a.ll (tuantities in New Hrunpshi :e, but t::.e State had not been considered a producer of" feldspar ui til lS3l. In the s::ring of tr .. at yea!', t:.e '[eane iic Products co. of Keene, N.H., beg3Il in a srr.9.ll way tl:e production of feldspar fro:n t1eir property in Gilsum, H.H., whicr. l-.a.d long been opera.tei a.s a :tl.ca mine. The purity of the feldspar at enoe '\ttracted f''.lvorai)le attention. and tt.e production of crude ore rapidly in­ cre'.\sed. Early in 1922, a new company, t'he Golding-Keene Co,

Sep 1, 1922

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By M. A. Schellhardt

"INTRODUCTION The augmented demands for natural gas in many parts of the United States as a result of war have increased the need for information regarding the producing characteristics of natural-gas and gas-condensate-type wells capable of delivering large volumes of gas, as such information is important to the formulation of conservative and efficient operative and recovery practices.,For many years, the capacity of natural-gas wells to produce gas has received studied consideration by Bureau of Mines' engineers, and three reports 3/ on gaging gas-well capacities have been published. In Report of Investigations 2929, Pierce and Rawlins point out that for accurate gaging, the actual pressures at the face of the sand in the well and the relationship between such pressures and the rates of flow of gas through the sand must be determined. Their report describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the wellhead.In Report of Investigations 2930, Pierce and Rawlins explain how the fundamental relation"

Aug 1, 1944

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

By Brian White, Hamid Maleki

Sudden, violent failures of rock around mine openings influence access, ventilation, and safety in both hard-rock and coal mines. To develop predictive tools for assessing the potential for violent failure, the authors initiated a comprehensive study using (1) multiple linear regression and numerical modeling analyses of geological and mining conditions at 25 sites to identify the most significant factors contributing to stress bumps in coal mines and (2) investigations of the geological and mining factors contributing to rock bursts in the Coeur d'Alene Mining District of northern Idaho, particularly the influence of preexisting structures on rock bursts. Twenty-five factors were initially considered in the study of coal bumps. The most important variables were identified as (1) mechanical properties of strata, (2) gate road geometry and/or gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, and (4) stress gradients associated with previous mining and anomalous geologic conditions. In the Coeur d'Alene district, burst damage related to preexisting structures results primarily from (1) sudden buckling and crushing of rock layers where surfaces of development and production openings lie at low angles to bedding, faults, or other planar structures and (2) disturbance of loose ground caused by seismic fault-slip on preexisting faults or previously sheared bedding planes that intersect veins near pillar-stope margins.

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory conducted a study of laser safety in potentially flammable environments. Researchers measured threshold igniting powers as a function of beam diameter for butane and propane-air mixtures by laser-heating targets placed on optical fiber tips using a 1064 nm laser. The minimum igniting powers for propane-air and butane-air were about 250 and 300 mW, respectively. Threshold igniting powers for propane-air were approximately proportional to beam diameter for beam diameters from 0.1 to 2.0 mm. Results suggest that relatively powerful beams may be used in these atmospheres without causing ignition, provided the beam diameter is controlled. Threshold ignition delay times using 91125 and 62.51 125 pm fibers were approximately proportional to the inverse square of the laser power. Ignition delays were about 45 ms or longer for laser powers up to 800 mW. Preproduction samples of a commercial optical fuse prevented ignitions under selected test conditions. A self-healing effect was observed for one sample. Comparisons are made with the results of other researchers. O 2006 Laser Institute of America. Key words: propane ignition, butane ignition, laser ignition, nonbeam hazards, fiber optic fuse

May 3, 2006

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and2-year time periods during 1990–1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 9, 2004

By W. H. Ode, W. A. Selvig

In 1938 , the Bureau of Mines cooperated with Subcommittee XV on Plasticity and Swelling of Coal ( C. C. Russell , chairman ) , of Committee D-5 on Coal and Coke , A.S.T.M. , by testing various methods for determining expansion and plastic properties of a series of coals of widely different coking properties . One of the tests made by the Bureau was the British Standard Method for the Crucible Swelling Test for Coal.5/ Briefly , this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties .. The number of the standard profile with which the maximum cross -sectional area of the button most nearly corresponds is recorded as the swelling index . Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization , it gave indications of having value in measuring free - swelling and caking properties of coals when burned on fuel beds . An opportunity to investigate this occurred when an engineer of an eastern public utility 'company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal . Some of these coals gave trouble by swelling 'excessively and clogging the grates . Samples were ob- · tained , and it was found that the troublesome coals gave decidedly higher free -swelling numbers than did the coals that performed satisfactorily . Also , it was found that the free - swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the · ´`standard volatile -matter test or from agglutinating - value results . The results of the free - swelling tests were considered by the Subcommittee on Plasticity and Swelling , and a special group of the subcommittee , under the chairmanship of R. A. Sherman , was delegated to study the test method . Ostborg , Limbacher , and Sherman , ofthe Battelle Memorial Institute , ' investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential -type stokers from the standpoint of the coking characteristics of the coal . Data were presented also showing that the indexes wer helpful in the selection of coal for industrial underfeed stokers .

Oct 1, 1946

By M. C. Irani

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1979

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

By V. A. Marple, K. L. Rubow

"IntroductionA particle dispersion system has been developed to aerosolize bulk powders or material deposited on surfaces such as filters. The size distribution of the aerosolized particles can then be obtained by sampling the particles with an aerosol sizing instrument such as a TSI aerodynamic particle sizer (APS) or a cascade impactor.Of particular interest is the applicability of using this technique to obtain the size distribution of particles collected on filters. This system has been used to determine the size distribution of coal dust particle collected on membrane filters. The use of this device in this application is quite intriguing in that, if this technique can be shown to accurately determine the size distribution of airborne particles, one can easily collect particle samples using either personal or area particle samplers, determine the mass concentration of the collected material through gravimetric techniques and then use the particle dispersion system coupled with the APS to determine the particle size distribution. With this technique one can determine the particle size of dust in environments, such as underground mines, where it would be inconvenient or impossible to use a particle sizing instrument.Particle Dispersion SystemA prototype particle dispersion system has been developed for aerosolizing particles. A schematic diagram of the system is shown in Figure 1. The system consists of mechanism for advancing the particle sample beneath a dust pickup tube, a venturi for deagglomerating the particles, and a instrument for analyzing the aerosolized particulate matter.The procedure to analyze a particle sample is as follows. The particles to be aerosolized are placed on a sample plate from where the particles are picked up by an air stream flowing upward in a small capillary tube (dust pickup tube). This tube operates as a small vacuum cleaner passing over the sample plate. The air is drawn up the capillary tube at a rate of 2 L/m by a venturi aspirator. This is accomplished by placing the outlet of the capillary tube near the throat of the venturi. The accelerated velocity of the air creates a low pressure in this region which draws flow up the capillary tube. From the outlet of the capillary tube particles are transported to the inlet of the APS where a small fraction are sampled and the aerodynamic diameter of the particles determined. The particles which are not measured by the APS are passed into a HEPA filter."

Mar 1, 1989

By Sathit Tandanand

Massive roof overlying the working seam in longwall operations can cause hazards if it does not cave readily behind the face supports. The overhang thus formed can overload the supports and endanger personnel when it collapses suddenly as a large rock mass. This Bureau of Mines report proposes the use of a concentrated load, either strip or point loading, applied onto the roof with the help of the upward thrust of the face supports. An experiment was conducted in the laboratory to obtain information about break characteristics and the values of significant parameters of three sedimentary rocks. The results were used to determine the breaking load requirement for a strong roof possibly encountered in typical longwall operations. The results show that the roof slab of moderate thickness can be fractured within the load capacity of off-the-shelf powered supports.

Jan 1, 1979

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007

By F. E. Griffith

Cost data are given for five methods of secondary backfilling of strip mines previously partially backfilled. The operations were conducted in north-central Pennsylvania; an average of 600 linear feet of highwall were backfilled in each trial. Major obstacles and the relative merits of the methods are discussed.

Jan 1, 1966