Search Documents

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By Marilyn Biviano

This analysis was conducted in response to concerns raised by the Chairman of the Energy and Commerce Committee of the House of Representatives regarding the potential impacts on automobile production, GNP and employment resulting from embargoing south African supplies of the platinum-group metals, platinum and rhodium. This analysis should be considered an addendum to the recently released study in which the direct economic costs I of a U.S. embargo on selected South African strategic and critical materials are estimated. The estimated GNP and employment impacts result when a mineral shortage reduces domestic industrial production and are in addition to the direct costs estimated in the earlier study. The direct cost to this nation resulting from a decision to embargo six south African strategic and critical minerals was estimated at $1.85 billion per year during the 1988-1992 time frame of the study. The estimated direct costs include the costs to U.S. consumers resulting from higher strategic mineral prices, lower mineral consumption, and the cost of developing higher cost domestic mineral resources. A large proportion of the costs result from the shortage of the two metals: platinum and rhodium. The average direct annual cost of embargoing is estimated at about $1.4 billion for platinum and $384 million for rhodium.2

Jan 1, 1988

By W. T. Millar

Magnetite mines in the Sterling tract, Orange County, N. Y., were operated almost continuously from pre-Revolutionary days until 1923. The Red-Back mine, one of several in this tract, was discovered in 1780; operated briefly in 1880; and abandoned, presumably because the iron ore contained considerable sulfur. The mine is in rough, mountainous country, with altitudes ranging from 500 to 1,100 feet. The magnetite deposit occurs in complex metamorphosed pre-Cambrian formation and is thought to be a replacement of limestone by magnetite. A dip-needle survey, completed in 1916, traced magnetic anomalies for a mile along the outcrop. A preliminary examination of the Red-Back mine was made by W. T. Millar, Bureau of Mines engineer, in December 1942. The Bureau of Mines bored seven diamond-drill holes aggregating 2,727.6 feet during the winter of 1943-44. A zone of magnetite mineralization was intersected in each of the holes.

Jan 1, 1949

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By Harold C. Pierce

"INTRODUCTION During the years 1941 to 1945, the United States produced less than one-half of one percent of all primary nickel, whereas the nation's consumption of the metal amounted to nearly three-fourths of the world's supply. Although postwar nickel consumption probably will be less than wartime consumption, trade- estimates for the next 10 years are well above the average established during the 1930-1940 decade. The greatest consumption is expected in nickel alloys, particularly nickel-alloy steels. 3/ The greater use of nickel cast irons and nickel-clad metals also signifies an expanding nickel market. In anticipation of the postwar demand for nickel, and realizing the seriousness of the ""have not"" position of the United States with respect to this metal, the Bureau of Mines, sent an engineer 4/ into the lower Copper River region of Alaska during the summer of 1944 to investigate the nickel deposits near the head of Canyon Creek. Samples from the Spirit Mountain nickel prospect were sufficiently encouraging to justify more intensive exploration. As a result, a program of surface trenching, systematic sampling, and detailed mapping of the property was adopted and directed by a Bureau of Mines engineer 5/ in the summer of 1945."

Aug 1, 1946

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973

By Launa Mallett, Charles Vaught, Kathleen M. Kowalski, Michael J. Brnich

This paper reviews research from the U.S. mining community to define issues relevant to an evolving national and international workforce and to relate them to the emergency response population. The authors further explore and relate the key problem of an aging workforce to the resultant changes and emerging physical and psychological needs of emergency workers. Finally, the authors cite examples from the mine emergency response community and mine rescue experiences to suggest practical recommendations that include both organizational and individual formats, with an emphasis on new approaches to training this changing workforce.

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

By Guy A. Johnson

The Bureau of Mines, through research and development contracts with the FMC Corp., has developed and tested two automatic fire sensing and suppression systems for large haulage vehicles. This work was undertaken to enhance driver safety, to lessen substantial property damage from fires on large trucks, and to increase the vehicle operator&apos;s productivity. One automatic truck fire protection system protects both the engine compartment and brake rid areas, while the second system is used in the engine compartment and fuel tank area. Both systems have redundant fire-sensing capabilities and manual override controls. Upon sensing flames and/or heat, the systems suppress the fire with pressurized, E-C class dry chemical. Both fire protection systems are flexible in design and can be modified for use on other mobile minim&apos; equipment. Prototypes of both systems have been subjected to long-term, in-mine validation testing and actual Eire tests on 100-ton-capacity trucks at the Puma mine near Tucson, Ariz., and the Erie mine at Hoyt Lakes, Minn. During the 4-month endurance test of the first system at Pima, an accidental flash fire occurred in the test truck while it was working in the pit. The system successfully sensed and automatically extinguished the fire with no injury to the driver and little damage to the truck.

Jan 1, 1975

By F. W. Richard

This paper describing the mining practices at the Ground Hog Unit of the Asarco Mining Co., a subsidiary of the American Smelting and Refining Co., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United Stated. The Ground Hog mine is at Vanadium in the Central mining district, Grant County, N. Mex., about 1.0 miles east of Silver City and 2 ½ miles southwest of Santa Rita. A branch line of the Atchison, Topeka & Santa Fe Railway connects Vanadium with Deming, about 45 miles southeast.

Jan 1, 1930

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By Clarence O. Babcock

This report describes the results of a Bureau of Mines investigation in which an elastic inclusion, orebody, or mining system is replaced for purposes of analysis with an imaginary effective inclusion of rectangular shape that encloses the region. This effective inclusion has averaged physical properties that are directly related to the average inclusion stresses. The results were in excellent agreement with those predicted by Donnell&apos;s theory (2)2 for an isotropic elliptical inclusion in a state of plane strain for all height-to-width ratios and for all degrees of inclusion hardness from very soft to very hard. The results are exact for an isotropic circular inclusion and provide an easy method of evaluating the stresses obtained by cylindrical inclusions in boreholes when the Poisson&apos;s ratio for both host and inclusion equals 0.25 for plane strain or 0.333 for plane stress. The theory was also used to predict the average stresses in 48 finite-element models of single transversely isotropic inclusions of ovaloid and rectangular shape. An interesting and useful observation from this work was that the forces on elliptical inclusions in the x and y directions, produced by applied uniaxial stresses in the y and x directions, respectively, were equal in magnitude but opposite in sign when the applied stresses were equal. This occurred when the plane strain condition was used with a Poisson&apos;s ratio of 0.25. The practical usefulness of the method is given by treating a variety of mining problems: (1) The average stresses in an orebody of irregular shape; (2) the average stresses in single-level room-and-pillar mining systems; (3) the average stresses in multiple-level room-and-pillar mining systems; (4) the effect of mining sequence on the average stresses produced during mining; (5) the stresses in cylindrical borehole plug related to host rock stresses as a function of plug hardness; and (6) methods for simplifying finite-element analysis of complex structures.

Jan 1, 1974

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992