Search Documents

By Robert H. Peters

Are the safety rules in your work place effective? Do supervisors enforce them as they should? Do supervisors abide by these rules? Safety rules are an important aspect of many company safety programs, particularly if employees must work in an intrinsically hazardous environment such as a coal mine. However, for various reasons, supervisors sometimes fail to enforce safety rules (Arvey & Jones, 1985; Hartshorn, 1998). This paper presents some findings obtained from interviews with coal miners about why supervisors sometimes fail to enforce an important mine safety rule. It also contains a few suggestions addressing what could be done to help supervisors perform this job function more effectively.

By E. R. Palowitch

A centrifugal float-and-sink test procedure has been developed by the Bureau of Mines to reduce the time for the gravimetric separation of coals finer than l4-mesh from as long as 24 hours to less than 1 hour. Comparative tests indicated that centrifuging a minus 14-mesh Pittsburgh-bed coal for 20 minutes at 1,500 revolutions per minute produced results that compared favorably with static float-and-sink test results. Standard deviations of the mean recovery and ash content of the float obtained centrifugally ranged from 1.31 and 0.04 percent, respectively, at 1.30 specific gravity to 0.21 and 0.05 percent, respectively, at 1.60 specific gravity. As in static separations, retreatment of the products separated at low specific gravities was required.

Jan 1, 1961

By Christopher Van Dyke, Edward L. Petsonk, Knox Van Dyke, Vincent Castranova, Ji-Hee Kang, William Pailes

"INTRODUCTIONPlatelet-activating factor (P AF) has been shown to mediate a broad range of biologic activities (1). Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group, an ester-linked acyl chain at the second carbon of the glycerol backbone, and an ether linkage at the first carbon. The alkyl group attached to the first carbon can exist in a variety of chain lengths, with the C16 and C18 forms predominant in humans. The structure of P AF has been identified as 1-0-alkyl-2-acetyl-sn-glycerol-3-phosphorylcholine (2,3).PAF can be released from a variety of cell types, such as basophils, neutrophils, and alveolar macrophages ( 4-6). Stimuli for the release of P AF include calcium ionophore, phorbol esters, chemotactic agents, and zymosan. In addition, endotoxin has been shown to be a potent stimulant of P AF release from alveolar macrophages (7).P AF has been shown to have a number of pulmonary effects. It has been associated with asthma since it can cause contraction of pulmonary tissue (8) and leukotriene secretion from leukocytes (9) and induce airway constriction when inhaled by humans (10). In addition, PAF is a potent chemoattractant and can cause migration ofneutrophils into the airspaces of the lungs (11,12). Endotoxin is a lipopolysaccharide-protein complex derived from the cell walls of gram-negative bacteria. I.PS is the lipopolysaccharide portion of endotoxin. LPS contains four covalently joined subunits: lipid A, 3-deoxyoctonate, a core polysaccharide moiety, and an 0-specific antigenic polysaccharide side chain. Rough LPS contains no 0-antigen side chain. The liP.id A portion of LPS has been associated with most of the biolQgic effects of endotoxin (13). This lipid A subunit consists of a D-glucosamine disaccharide backbone substituted with four fatty acid side chains. Endotoxin is found in a wide variety of occupational settings associated with organic dusts derived from plants or animals, such as cotton, cereal grains, silage, rice, and poultry (14-18). In addition, airborne endotoxin has been found in sewage treatment plants, composting plants, offices with contaminated humidifiers, and showers or saunas (19-22)."

Jan 1, 1990

By Hillary W. Clair

An equation is derived for the rate of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing . The equation takes into consideration the reaction rate coefficient , transport through the gas and through the porous shell of reduced oxide , the rate of gas flow , and the volume of the enclosure . The equation serves as a model for predicting the course of reduction of a particle of metal oxide in a shaft furnace .

Jan 1, 1964

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By George Saliba

This report disucsses the formulation of a mathematical model for the steering of a conveyor belt by a flat return idler and a troughed idler under various loading conditions. Significant parameters associated with belt training are identified. The generation of a skewed flat return idler model in terms of a steering force and self-aligning torque is presented. Development of the mathematical model for the flat return steering idler is illustrated for the case of no circumferential slip occurring and for the assumption of a bidirectional slip mechanism. Experimental results supporting the theoretical analysis is presented.

Jan 1, 1977

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By J. A. Eisele

The Bureau of Hines conducted a bench-scale investigation of a concentrated H2S04 reaction for recovering and separating rare-earth elements, barium, and strontium from a bastnasite ore and byproduct. Barium and strontium were dissolved in the concentrated acid and precipitated as a mixed product by water dilution. Separation of strontium from barium was effected by reaction with Na2C03 solution, followed by a dilute acid leach of the SrC03 formed. After removing the barium and strontium from bastnäsite are, the rare-earth elements were roasted to water-soluble sulfates. The rare-earth sulfate solution was subsequently processed by solvent extraction to produce rare-earth oxides low in lead and magnesium.

Jan 1, 1974

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

By C. D. McMaster, John C. Hartley

Three systems that monitor ventilating fans are described . These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown .

Jan 1, 1964

By Neal M. Muir

The increasing demand for iron ores prompted the Bureau of Mines to investigate the sources of past production in Kentucky to determine whether reserves of usable ore still exist. Preliminary investigation showed that the holdings of the Rose Run Co. were the most promising, inasmuch as the deposit had not been exhausted by past mining and the property was near railroad facilities and but 80 miles from the blast furnaces at Ashland, Ky. The Bureau conducted a churn-drilling and sampling program to investigate the depth, thickness, and iron content of the ore beds so that they might be evaluated as a possible reserve of low-grade iron ores. The Rose Run area in Bath County, Ky., was explored by 74 churn-drill holes totaling 2,059.4 feet of drilling and 4 cuts and test pits. Fifty-seven drill holes and the four test pits penetrated the ore bed at an average depth of 22 feet. The bed had an average thickness of 2.54 feet. Analyses show that the calcium and magnesium carbonate content is more than sufficient to flux the silica and provides an excess that needs an admixture with other siliceous iron ores.

Jan 1, 1950

By Frank L. Wideman

This information circular describes methods used in mining inclined beds of phosphate rock in mines operated by San Francisco Chemical Co. in Rich County, Utah. The mines are on the western flank of the Crawford Mountains, a short, narrow range in northern Utah near the Idaho-Wyoming corner (fig. 1). The western front of the range is a conspicuous wall of folded and faulted sedimentary rocks that rises abruptly 300 to 600 feet above the floor of the adjacent Bear River Valley. Rex Peak, highest point in the range, is approximately 8,000 feet above sea level. The area surrounding the mines is sparsely populated. Randolph, the county seat of Rich County, has a population of 650. It is 10 miles southwest of the mines by road and the only town in their vicinity.

Jan 1, 1958

By C. B. Strachan

The Mascot concentrator treats 1,900 tons of zinc ore per day by gravity concentration and flotation. During the year 1929 the heads averaged 2.90 per cent zinc, and the recovery was 90.15 per cent; the concentrates produced contained 60.19 per cent zinc. ACKNOWLEDGMENT Acknowledgment is made to M. H. Newman, geologist, Robert Ammon, chief metallurgist, D. B. Grove, mill superintendent, and W. A. Calhoun, metallurgical clerk for assistance in the preparation of this paper.

Jan 1, 1930

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By A. D. Bauer

For several years the Bureau of Mines has conducted surveys to determine the changes in motor gasoline being sold throughout the United States. The present survey shows that far the districts in which samples were collected, the average gasoline is becoming more volatile instead of less so, as is sometimes supposed. This year's gasoline is much more volatile than that sold two years ago, and it has a somewhat better distillation range than last summer's samples. A comparison of the average figures for several years, shows that motor gasoline is also becoming more uniform in character. The large seasonal change is disappearing, but ?winter gasoline', still has a lower initial boiling point than "scanner gasoline". This difference in volatility is made intentionally to facilitate starting the motor in cold weather. The end point shown in the present survey is slightly lower either than that of last winter or of the summer of 1921.

Jan 1, 1922

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977