Search Documents

By John W. Adams, W. D. Bensema, Motohisa Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No. 4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief tine periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 4, 1974

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By W. W. Odell

"It has long been recognized that coke is a more desirable fuel than bituminous coal in water-gas apparatus of present design, but still considerable headway has been made in the use of the latter fuel as a substiaute for coke. This is particularly true in the Central States where the supply of high-grade coke has been very limited and uncertain during the past few years, and where coking coals of low sulphur content were available in quan¬tities. In fact, with, the present difference in price of coal and coke, it is possible to realize a marked saving when using a coking bituminous coal as generator fuel.Difficulties have been encountered in the use of such fuel, but they have, to a large extent, been overcome. One of the chief obstacles in the use of the more general utilization of bituminous coal for water-gas manufacture, is the fact that, with normal operation, the capacity per unit of time is reduced. This of course is a serious problem for plants operat¬ing at capacity with coke fuel. However, this difficulty can, to a large extent, be remedied by a changed method of operating, and can be entirely remedied by a combination of the latter with a change in the design (or proportions) of a water-gas set. The preceding statement, the reader will understand, refers more particularly to a carburetted water-gas set.In the manufacture of water gas from coke, present practice requires that for continuous 24-hour service the heat of combustion of all the carbon monoxide (CO) generated during the air blow be utilized in addition to the sensible heat of the gas coming from the generator. This is doubly true when making carburetted water gas from bituminous coking coal. The reasons why this is so are apparent when the following factors are considered."

Nov 1, 1920

By Jacqueline H. Jansky

The Bureau of Mines conducted a study to determine the relation-ship between geologic features and linears. Cleats, kettlebottoms, and roof rolls were mapped and superimposed on the linear plots for a coal mine in West Virginia. No clear relationships were evident. This may be due, in part, to the mining practice of leaving head coal, which obscures geologic features that may exist in the roof. Future studies should concentrate on mines where roof is extensively exposed.

Jan 1, 1982

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1984

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By S. P. Sandoval, A. E. Clark, S. W. Yopps, J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 1992

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

By William J. Campbell

The possibility of chemical analysis by identification of characteristic X-ray spectral lines was first suggested by H. C. J. Moseley in 1913.3/ For a given spectral series it was found that the frequency of the characteristic radiation was proportional to the square of the atomic number of the excited atom. Siegbahn and his coworkers improved the instrumentation and accurately determined the wavelengths of the characteristic spectra for most of the elements .4/ In fluorescent X-ray spectroscopy, the characteristic X-rays of atoms are emitted or fluoresced upon absorption of primary or incident X-rays of shorter wave-lengths (higher energies). The K spectral lines are used for elements of atomic numbers 13 to about 63, and the L series for those above atomic number 50. Whether the K or L lines are used for elements 50-63 depends upon the type of instrumentation available. The laboratory at the Eastern Experiment Station of the Bureau of Mines, College Park, Md., uses the K lines up to atomic number 57 and the L lines for thong elements of higher atomic number.

Jan 1, 1955

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By D. H. Chambers

Digestion studies were undertaken to develop a method for the rapid dissolution of high-temperature ferroalloy scrap. Laboratory tests showed: (1) dissolution of alloy scrap with ferric ion as the leaching agent was a moderately rapid method of digestion; (2) the dissolution process can be considered as a typical reaction of a metal with chlorine gas, although evidence was obtained to show dissolution as a two-step process, one step as the reduction of ferric ion by the soluble alloy constituents and the other as the oxidation of ferrous ion with chlorine gas; and (3) the attack of ferric ion on the alloy was a function of alloy composition, ferric to ferrous ion ratio, and area of contact between leach solution and alloy. The exceedingly complex nature of alloy compositions and dissolution products generally precluded satisfactory analytical determinations. Results of moderate accuracy were obtained using complex modifications of standard analytical and spectrographic techniques.

Jan 1, 1968

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By Leonard F. Heising

At the Groveland mine iron ore is mined by open-pit methods and concentrated by means of spirals and flotation. A brief history of the mine and its early development is given. The ore deposit is described, with emphasis on those physical characteristics that affect the choice of mining and milling methods. Development and mining, which include breaking ground, loading, transportation, engineering, and operating control, are explained, and the milling method is described Mining and milling costs are given in percent of total cost.

Jan 1, 1963

By Donald P. Blasko

The first well that produced commercial quantities of oil in the Cook Inlet Basin of Alaska was completed in 1957. Since that time oil production in the basin has increased rapidly and by the end of 1969 had reached an annual rate of 74 million barrels. Five major oilfields had been developed, and two additional discoveries awaited development. Estimated amounts of recoverable oil by primary and secondary recovery methods total 2.7 billion barrels, or 36 percent of the estimated oil originally in place. Repressurization by injecting gas or water in formations containing undersaturated oil has significantly increased the volume of recoverable oil. All production has been from formations of the Tertiary age; that much of it is from depths of 10,000 feet or more is unusual for Tertiary formations. The oils are low in sulfur and contain low to moderate amounts of asphalt.

Jan 1, 1972

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electro-kinetic dewatering and consolidation of metal-mine mill tailings from five mines in the Coeur d'Alene, Idaho, district. Classified (coarse) tailings, slimes, and unclassified material were separately tested. Tailings were placed in 0.3 ft3 plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Moisture content and density of the dewatered material at test end indicated the method to be generally effective for all materials examined, but best results were achieved with well-mixed unclassified tailings.

Jan 1, 1974

By S. P. Holt

The Rush & Brown mine has been one of the most consistent small producers of copper ore in the history of Alaskan mining. Approximately 50,000 tons of ore have been shipped to smelters from the property. Production has been made from two distinct and separate ore bodies of dissimilar types. The Shear Vein deposit has been mined to a depth of 500 feet below the surface without a reduction in the size of the ore shoot or the grade of ore. The Magnetite ore body has been partly mined to a depth of 200 feet below the surface. Because of the favorable production record of the Rush & Brown mine, the present need for copper and the fact that the owners were attempting to place the mine in production, it was deemed advisable to investigate this property under the Strategic Minerals Act of 1939 as a possible source of copper.

Jan 1, 1948

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By Howard C. Turnage, Dana T. Updyke, Wayne C. Muhler

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leaky feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 6, 1980