Search Documents

By R. V. Lundquist, H. Leitch

Two hydrated calcium aluminates , formed by side reactions in the leaching step and desilication step of the lime- soda sinter process , were investigated to better define their influence on alumina recovery . The two calcium aluminates , Caз [ Al ( OH) 6 ]₂ and зCa0.Al½ 03 · ( 8-12 ) H₂ ) , were prepared and identified by chemical and X- ray analysis . The relative proportions of each of these compounds formed in typical leach solutions at several temperatures were determined . The influence of free lime as a promoter of calcium aluminate formation was also investigated . The formation and precipitation from leach liquors of calcium aluminates contributes to the low alumina recoveries in the process . The presence of carbonate ion in the leach solution suppresses calcium aluminate formation and precipitation and results in higher alumina recovery . Hydrated calcium aluminates are formed in the aging of lime - soda sinters in the normal atmosphere .

Jan 1, 1963

By William H. King

The Mercur Dome mine is in the Camp Floyd mining district, Tooele County, Utah (fig. 1). The property lies between 6,000 and 8,000 feet altitude on the southwesterly slope of the Oquirrh Mountains, a short distance west of Mercur, the district settlement. Mining began in the Mercur area in 1870. Operations at the Mercur Dame mine were started in 1937 after several claims had been consolidated into one group. Preliminary examination of the ground by F. H. Gunnell, a Bureau of Mines engineer, disclosed the presence of vanadium in a carbonaceous shale horizon. Rocks near the Mercur Lame property are chiefly sediments of Carboniferous age, including the Madison and Deseret limestones. The main shaft penetrates the Deseret formation to a point a few feet above the 1,000-foot level where it enters the Madison limestone. The flat-lying vanadiferous shale horizon is exposed on the 1,000-foot level near the top of the Madison limestone. The Bureau of Mines development program, consisting of diamond drilling, auger hole drilling, and sampling, was planned to determine the extent and assay value of the vanadiferous bed. Seven diamond-drill holes totaling 300 feet were drilled from the 1,000-foot level of the mine. Eight hand auger holes were drilled in the back of the drift on this level (fig. 2). Assay determinations were made on 74 samples from the drill holes and supplemental channel samples and are tabulated in this report. The concluding section embodies results of metallurgical tests.

Jan 1, 1949

By Christopher C. Jobes

Computer-aided control of a mining machine requires a guidance system to aid remote positioning of the machine by determining its position and heading. The mechanical position and heading system (MPHS) developed by the U.S. Bureau of Mines provides such navigation information during face maneuvers. This report describes the required theory, which yielded a reliable algorithm for calculating machine position and heading, and implementation of this theory in hardware and software design, which made surface testing of the MPHS possible. Analysis of the errors and test results showed that the MPHS provides reliable results and can, therefore, provide useful guidance information for face navigation.

Jan 1, 2010

By W. E. Young, D. T. Delicate

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Nov 1, 1963

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976

By M. Hayashi

The Bureau of Mines conducted laboratory studies on low-grade vanadiferous silicates from the Pumpkin Buttes and Nine Mile Lake deposits of Wyoming to examine techniques for extracting vanadium and uranium. Recovery from low-grade sources such as these could contribute to future vanadium production and reduce reliance on vanadium imports. The Pumpkin Buttes samples contained 0.03 to 0.04 pct V205 and 0.06 to 0.12 pct U308; the Nine Mile Lake samples contained 0.02 to 1.0 pct V205 and 0.06 to 0.19 pct U308" Leaching the Pumpkin Buttes samples for 18 h at 800 C with addition of 200 lb/ton H2S04 resulted in recoverey of 80 pct of the vanadium contained in the samples. The Nine Mile Lake samples were readily leached, yielding 78 to 94 pct of the vanadium after 3 h at 800 C with addition of 100 lb/ton H2S04, A solvent extraction procedure was used to selectively recover urani-um from Pumpkin Buttes and Nine Mile Lake leach solutions and to recover vanadium from the raffinates. In batch shakeout tests, Alamine 336 recovered over 95 pct of the uranium from leach solution adjusted to pH 1. Di-2-ethylhexyl phosphoric acid and Cyanex 272 recovered vanadium from the uranium raffinate after reduction and adjustment to pH 2; vanadium extractions of up to 96 pet and 92 pct, respectively, were achieved.

Jan 1, 1985

By Charles Sabine

In 1984 and 1985 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 27,420-acre part of the 36,600-acre Southern Inyo Wilderness Study Area, CA-010-056, in order to evaluate the mineral resources. The study area is located in Inyo County, CA, near the town of Lone Pine, about 180 miles north of Los Angeles. The study area takes in most of the western slope of the southern Inyo Mountains. Terrain is steep and rugged; the climate is arid. The study area is underlain by folded and faulted marine sedimentary rocks dating from Ordovician to Triassic, Triassic volcanic rocks, and Jurassic to Cretaceous plutonic rocks. Most mineralization was along faults and shear zones in sedimentary rocks. The study area includes most of the Russ and Lone Pine mining districts which produced over one million dollars in gold, silver, lead, and zinc, mostly between 1860 and 1890. A few mines produced ore as late as 1951. Most production was from the Reward, Silver Spur, Long John, and Pennsylvania mines which are outside the study area. Presently, there is no mining activity in the study area; some development work was done at the Reward mine between 1981 and 1984. Dolomite marble is quarried from the base of the range outside the study area. There are currently about 70 mining claims in the study area.

Jan 1, 1986

By J. A. Herdlick

The Star mine, near Neihart, Cascade County, Mont., has been in continuous operation since the construction of a 50-ton bulk flotation mill in 1939. The mine was examined by G. N. Bennett, an engineer of the Bureau of Mines, in November 1942. At that time the life of the operation appeared to be limited and a program of crosscutting and core drilling were recommended. The program had as its objective the investigation of a promising undeveloped area lying west of the Star vein and, if possible, the development of enough reserves in this area to insure continuous operation during the war emergency. Development of additional reserves would then justify necessary changes in the mill in order to eliminate the heavy penalties imposed for excess zinc in the bulk concentrates. The Bureau of Mines work began in February 1944 and was completed in September 1944. The project was started by Wilder R. Brinton and continued by Thomas W. Oster, mining engineers in the Bureau's Montana district office. Beneficiation tests on are and concentrates were made after completion of the underground work. This report presents the factual data obtained during all phases of the Bureau's investigation.

Jan 1, 1949

By J. E. Hamak

This publication contains analyses and related source data for 162 natural gas samples from 15 states and 4 foreign countries. Of the total samples, 154 were collected during calendar year 1992. The remainder were collected earlier, but releases granting permission to publish were not received until 1992. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1993

By R. L. Crosby

The Bureau of Mines investigated alloys of copper with 2, 3, and 4 vol pct alumina and with 2 vol pct yttria. Alloys were prepared by a coprecipitation process and were fabricated by pressing and sintering of powders, extrusion, and swaging. Tensile properties at room and elevated temperatures, stress-rupture strength, electrical conductivity, and density were measured. The superiority in elevated temperature strength of dispersion-strengthened copper to OFHC copper was confirmed. Increasing the oxide content from 2 to 4 vol pct produced only a small improvement in strength properties and decreased the electrical conductivity. The 3 vol pet alumina alloy had the best overall combination of properties.

Jan 1, 1969

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

This manual covers the operation and lubrication procedures for the Eimco Pumpable Roof Bolting Machine. This machine meets U. S. Bureau of Mines Schedule 2G Approval. This manual is divided into three major parts: 1. Machine dimensions; 2. operating instructions and; 3. Lubrication. Whenever front or rear, right or left arc mentioned it is assumed that the reader is standing behind the machine looking toward the boom. The boom is at the front of the machine. Safety When leaving machine parked on an incline turn wheels into the rib or block wheels. Do not run over power cables. Make sure your power cable is up out of the way so others can't run over it. Machine has a fire suppressor system for the power unit. The remote actuator (pressure cylinder) is located at the operator's station. Components and service procedures on page 59.

Jan 1, 1976

By Lewis M. McNay

Description of methods employed and cost data are given for surface-mined land reclamation in Moraine State Park, Butler County, Pa. This project was conducted under the authority of the Appalachian Regional Development Act; a total of 177 acres of land was rehabilitated for specific land use purposes. The use of large equipment expedited the project work, and similar results could be anticipated on similar reclamation programs.

Jan 1, 1970

After nine years of negotiations, the U.N. Conference on the Law of the Sea approved a Law of the Sea Treaty text in April. Israel, Turkey, the United States and Venezuela voted against the text and 17 other nations including Belgium, the Netherlands, Italy, the Soviet Union, the United Kingdom and West Germany abstained. These nations still have the option of joining the treaty when it is opened for signing in December. However, the Reagan Administration has stated that several provisions of the deep seabed mining portion of the text are unacceptable and it seems unlikely that the United States, at least, will change its position. ALUMINUM Reynolds Metals Co. has criticized an Oregon state plan to relax air pollution standards for aluminum plants. The company feels that relaxation of the rules does not go far enough. Reynolds officials say that they have spent about $31 million at their Troutdale plant for state-of-the-art pollution control equipment, and if they are required to make the pollution reductions called for in the 1986 rules, Reynolds would be forced to close the 40-year-old plant.

Jan 1, 1982

By Edward F. Redente

Several research projects have been conducted in the western United States to determine the optimum soil replacement thickness for reconstruction of rangeland and cropland. However, the information gained from these studies tends to be site-specific and not broadly applicable. Moreover, the possible interaction between soil thickness and mechanical and fertilizer manipulation of the overburden has not been adequately studied. To meet these information needs, research was initiated at Trapper Mine in northwestern Colorado in 1980 to study vegetation response to soil thicknesses of 15,30,45, and 60 cm and five manipulations that included disking, ripping, and fertilizing. All crops were harvested at peak standing crop and then weighed in the laboratory. Wheat grain yields were highest when soil thickness was 45 cm and the soil and overburden were ripped. Alfalfa yields appeared to be highest when overburden was disked and fertilized and soil was replaced to a thickness of 60 cm. For range vegetation, standing crop biomass was highest when overburden was ripped and soil was replaced to 60 cm thick. However, optimum performance was obtained from the maximum number of species and life forms by disking overburden and replacing 15 cm of soil. The performance of most range plant species has improved over the three years of the study. When the results of this study are compared to the results of other soil thickness studies, we can conclude that selection of management practices should be influenced by local climate, local soil and overburden conditions, type of crop or vegetation to be grown, and specific management goals for that crop or vegetation.

Jan 1, 1984

By C. A. Frenzel

Extensive spectroscopic data are needed in making reliable vibrational assignments for use in calculating thermodynamic functions of polyatomic molecules. The fundamental vibrations of organic molecules may be observed at any wavelength from 2.5 to 200 microns (micron = µ = 10-4 centimeters), but most often in the region from 3µ to 50µ. Raman spectra generally cover the range in which fundamental vibrations occur, but equally important infrared spectra usually are not measured at wavelengths longer than 25µ. This limitation results because most infrared spectra are determined for analytical purposes, which seldom require information outside the region 2µ to 25µ. Measurements of infrared spectra in the range 15µ to 35µ recently were begun by the Bureau of Mines to obtain data needed in making vibrational assignments. This report presents the spectra of the following thirteen compounds: Tetrahydrofuran, 1-methylpyrrole, piperidine, 2-methylpyridine, 3-miuthylpyridine, 2-propanethiol, cyclopentanethiol, 2-methyl-2-butanethiol, 3,3-dimethyl-2-thiabutane, cyclohexanethiol, cyclopentyl-l-thiaethane, 2,4-dimethyl-3-thiapentane, and hexamethyldisiloxane.

Jan 1, 1960

By J. W. Miller

From 1889, when the first railroad shipments of coal were made from McDowell County, W. Va., until today, the coals produced from the New River and Pocahontas groups have had a good reputation as premium low-volatile coals. Although there has been a large production from the Pocahontas No. 3 and. Pocahontas No. 4 beds, considerable reserves remain. This Bureau of Mines publication is one of a series appraising the Nation's coking-coal reserves by presenting data on the basis of which the practicability of upgrading marginal deposits to metallurgical standards can be determined. This study of the preparation characteristics of McDowell County coals is the second of the series to be undertaken in West Virginia. The Pocahontas No. 3 and No, 4 beds have not been included because their washing characteristics are well known.

Jan 1, 1954

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By J. M. Seward, W. D. Dietzman, M. E. Hawkins

Analytical studies of formation waters are widely used by the petroleum industry as an aid in solving problems such as identifying intrusive waters , corrosion studies , treating injection water , and choosing open or closed water- injection systems . The solution of a problem is often simplified when reliable analyses of the waters under consideration have been made previously . Chemical analyses and electrical resistivity measurements are presented on 267 samples from 74 fields in south Arkansas , and 199 samples from 80 fields in north Louisiana .

Jul 1, 1960