Search Documents

By D. S. Kingery

Efficient transportation is necessary to complement modern mechanized mining methods. The increasing trend toward high-capacity face loading equipment has demanded equally efficient haulage methods; this has been met by increasing mine-car sizes, using larger locomotives, and increasing haulage speeds, all requiring properly installed and maintained haulage roads specifically designed for this type of traffic. The recommendations and specifications included in this circular were made to point out salient factors important to the proper construction and maintenance of track haulage roads and to serve as recommended standards for track installation and maintenance. GLOSSARY OF TERMS USED Haulageway. - The track, walkway, trolley wire, feeder lines signal end telephone lines, signals, telephones, support, and drainage of the entry referred to. Subgrede. - The base upon which the ballast is laid.

Jan 1, 1954

By Keith L. Harris

Real gross national product3 (GNP) grew at a seasonally adjusted annual rate of 4.2% in the fourth quarter compared with a revised 4.3% rate in the third quarter, according to the most recent estimates released by the U.S. Department of Commerce (table 1). Expanding inventories, Government purchases of goods and services, residential fixed investment, and a narrowing of the trade deficit fueled the growth. Significantly reduced consumer demand led to the heavy inventory growth. Almost half of the buildup in inventories consisted of automobiles because consumers reduced purchases when Detroit ceased most incentive programs in late summer. Reduced consumer demand also affected imports, however, and the narrowing of the trade deficit resumed after widening in the third quarter. Nonresi- [ ] dential fixed investment also declined after a strong gain in the third quarter. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 2.9%, the same as that of 1986. However, on a fourth-quarter-to-fourth-quarter basis, the real growth reached 3.8%, the highest growth since 19M, and exceeded the Reagan Administration's estimate of 3.4%. Rising merchandise exports accounted for about one-third of the growth in GNP for all of 1987 and are expected to continue to grow as domestic manufactures benefit from the lower value of the dollar vis-a-vis other major trading country currencies. Consumer demand became a less important factor of economic growth, but employment continued to grow (table 2), and civilian unemployment declined by 0.9 percentage points (December to December) as the industrial sector geared up to increase exports. Inflation, as measured by the fixed-weighted GNP price index, remained low at 3.4%.

Jan 1, 1988

By C. J. Chindgren, L. C. Bauerle, J. B. Rosenbaum

Modifications of the conventional method of preparing ductile vanadium metal by calcium reduction of V2 05 in a bomb were explored for clues to a more economical procedure . The modifications examined included ( 1 ) omitting the gas purge of the bomb ordinarily used for eliminating atmospheric nitrogen , (2 ) using low- grade vanadium feed materials , ( 3 ) using alternative reductants , such as aluminum , magnesium , and silicon , and reductant mixtures , and ( 4 ) bomb refining of aluminothermic metal produced in open- vessel reductions . The most promising modification appeared to be bomb refining , using calcium to purify vanadium metal -- of low aluminum but high oxygen content-- prepared by open- vessel aluminothermic reduction of vanadium pentoxide .

Jul 1, 1960

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By Constantine C. Popoff

"INTRODUCTION AND SUMMARYDuring 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington.The investigation consisted of transit and topcgraphic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and. analysed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing now sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest."

Oct 1, 1948

By Ludwig Schmidt

The petroleum industry has recently shown sucks great interest in the evaporation of crude oil and of gasoline, and in the prevention of evaporation losses that almost daily there is being developed and placed on the market equipment designed especially to reduce these losses. Among the recent developments is a new type of tank roof known as the "floating roof," which practically eliminates the vapor space over the surface of the oil, thus removing one of the chief causes of evaporation. There are at the present writing at least two types of floating roofs which, while similar in fundamental principle, differ mainly in the method of making contact with the inside shell of the tank. One type of floating roof is known as a floating tank deck, and has on its circumference flexible metal baskets containing gravel that .rest against the inside shell of the tank. In the other type of floating roof contact with the tank shell is made by the use of movable buffers or shoes. These are attached to the outer ring of the roof and are pressed against the tank shell by means of springs.

Jan 1, 1923

By Y. Miron

'This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, g the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2).

Jan 1, 2010

By Paul M. Tyler

This paper is one of a series of digests of foreign mining legislation and court decisions prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Yugoslavia was prepared from information furnished by John Dyneley Prince, American Minis- ter at Belgrade, in response to a questionnaire submitted by the Bureau of Kinos and transmitted through the courtesy of the Department of State.

Oct 1, 1929

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By Walter J. Frank

The purpose of the work covered by this contract is to develop a means of designing splice connectors which will significantly improve mine trailing cable splice performance. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. Because of the empirical nature of this effort, time has been devoted to explaining the derivations of the test procedures used. Special attention is given to the splice flexing machine which served as the backbone of the test program. In order to familiarize persons with connector terminology, a section is devoted to a glossary of pertinent terms. Various types of cable joints are also defined. The major effort is a connector design parameter study. Utilizing the optimum parameters developed along with the suggested design procedure outlined in Appendix I should result in significantly improved splice performance and thus meet the objectives of this contract. A field test program was instituted for the purpose of insuring adaptability of connector design and associated installation tooling along with a field performance study. During the course of work, other significant factors affecting splice performance were uncovered. Although not covered by the scope of this contract, a brief discussion is presented for the purpose of stimulating interest in what is considered other fruitful areas for improved splice performance.

Jan 1, 1976

By G. T. Fisher

The material requirements of carbide cutting tools for machining steel and cast iron are dependent on WC bonded with Co, with additions of TaCand TiC. The Bureau of Mines is conducting research to devise substi-tute materials, based on Ni-alloy-bonded TiC, for C-5-grade cutting tool applications. This substitution would result in less dependence on foreign sources for Co, Ta, and W, and use of lower cost materials. In this preliminary study, the Bureau investigated the effects of composition and processing variables on the transverse rupture strength and hardness of Ni-alloy-bonded TiC to identify compositions that exhibit promising mechanical properties. Further systematic modification of these compositions by soild-solution strengthening additions would subsequently be evaluated to obtain cutting tool materials with requisite properties and performance for C-5 applications. Compositions for evaluation were prepared by a powder metallurgy method of cold-pressing and liquid-phase sintering. Complementary analysis of compositions included chemical analysis, X-ray diffraction, energy-dispersive X-ray spectro-scopy, and density measurements. Based on results of this investigation, promising compositions were determined to be 59.37TiC-25Ni-5Mo-lO.63Mo2C, 59.68TiC-25Ni-3.33Mo-1.77Mo2C-6.67W-3.55WC, and 59.35TiC-25Ni-l.67Mo-3.54Mo2C-3.33W-7.1WC.

Jan 1, 1987

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By Andrew Allan

During recent years underground production for the Pennsylvania anthracite region has reached the lowest output per man per day figure of the last decade and a half. This fact, combined with increased unit costs for labor and material, has forced the market price of anthracite ever higher. Over the years the mines have become deeper, and haulage distances have increased, thus adding to the mining costs. The industry now recognizes the need for new mining techniques to offset increasing costs. The Federal Bureau of Mines, through its Anthracite Research Laboratory, is engaged in a program of underground-mining research in cooperation with anthracite-producing companies to aid in reestablishing the economy of the region by introducing methods and/ or machines that will reduce underground-mining costs and, at the same time, enhance the safety of the workmen.

Jan 1, 1953

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an exten- sion of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, how- ever, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's pro- duction facilities are maintaining a satisfactory quality control.

Oct 1, 1965

By Charles S. Allbright, Frank G. Schwartz, Marvin L. Whisman

Radioactive tracer techniques were used to gain a better knowledge of the types of compounds that cause gum formation in gasoline during storage . A selected organic compound was labeled with tritium and purified . An unstable gasoline was tagged by adding a small amount of the labeled compound . After storage of the gasoline at 110 ° F for 16 weeks , the gum that had formed was recovered . The amount of the test compound converted to gum was determined by liquid scintillation counting . About 70 compounds , including several classes and types , were studied . The compounds , listed in order of descending reactivity in the test fuel , were sulfur compounds , nitrogen compounds , polycyclic hydrocarbons , olefins , alkylbenzenes , and saturates . In the order of decreasing percentage of each in the gum , the compounds were monoolefins , alkylbenzenes , sulfur compounds , polycyclic hydrocarbons , nitrogen compounds , and diolefins . This type of information should be helpful in developing a method for predicting the storage stability of gasoline .

Jan 1, 1964

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010