Search Documents

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

By L. C. IlsLey

Most State enacting bodies have deemed it necessary to specify a maximum speed at which men may be hoisted or lowered in mine shafts. Since most mine cages are not closed in, as are passenger elevators in office buildings, and since, ordinarily, neither the starting tin g nor stopping of the cage is as general as that of these elevators, such regulations are all the more necessary for the comfort and safety of the men. It is also quite generally recognized that it is dangerous to over-crowd cages. Hence, a number of States have limited the number of men that may be on cage at one time.

Jan 1, 1939

By David Schlain

The galvanic corrosion properties of titanium in contact with commercially pure aluminum, copper, or type 302 stainless steel in some of the common organic acids were investigated. Acids used in these experiments were 10 percent formic, acetic, lactic, citric; 1 percent oxalic and tartaric; and 9 percent oxalic. Electrode-potential measurements and several types of galvanic couple experiments were carried out. Solutions were aerated by three methods: Flow of air, flow of helium, and natural aeration. Work was done at 35° C. with couples consisting of equal areas of the 2 metals. Titanium was resistant to corrosion in most of the organic acids studied, whether alone or in contact with a dissimilar metal. However, titanium coupled with aluminum did corrode in 1- and 9-percent oxalic acid solutions. Contact with titanium usually caused aluminum to corrode by galvanic action. Copper was subject to galvanic attack in 10-percent acetic acid with a flow of air. Contact with aluminum to some solutions in which titanium is ordinarily inert and noble with respect to aluminum caused titanium to corrode

Jan 1, 1956

By Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep sandstone in the Elk Basin field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes of gas in solution, saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep reservoir of the Elk Basin field has unusually varying physical characteristics, such as a saturation pressure of 1,250 pounds per square inch absolute and 490 cubic feet of gas in solution in a barrel of oil at the crest of the structure, and a saturation pressure of 530 pounds per square inch absolute and 134 cubic feet of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the 6a r; in solution in the oil varies from 18 percent for oil on the crest to 5 percent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of oil in the structure. Many geologists and petroleum engineers have considered all the oil in a petroleum reservoir to have uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas. That such is not always so is borne out by the results of the study made by the writers.

Jan 1, 1951

By Peter H. Toepfer

Hydraulically emplaced, classified mill sands long have been used for stope fill. Entrained water drains rapidly from this type of fill through openings between the sand grains. Slimes are removed to facilitate drainage of the water, thereby lowering dangerous hydrostatic pressures in the fill. Use of unclassified mill tailing as practiced at the Dayrock mine is a recent development and represents a fundamentally different approach to the problems of inhibiting the development of hydrostatic pressures within the stope fill. At the. Dayrock mine, mill tailing is used to form a densely packed fill of sand and slime particles relatively impervious to additional water.

Jan 1, 1952

By E. L. Garton

Bureau of Mines routine crude-oil analyses of 88 samples from 60 fields are presented in this report. Similar analyses from other fields in California have been published in previous reports listed in the appendix, page 52. Yearly production of crude oil in California and the percentage of United States production represented by California production for 1948-54 are given in table 1. [ ] Analyses in this report are of samples from the fields listed in table 2, with production data for 1953, cumulative production through 1953, and year of discovery of each field. Information regarding the source and general characteristics of the samples is included in table 3 with a summary of analytical and computed data.

Jan 1, 1956

By P. L. Swanson, A. T. Iannacchione, W. J. Gale

This paper outlines the concepts used to correlate rock failure with microseismic events and presents examples of microseismic monitoring together with associated computer modelling of the rock failure. This study is motivated by the need to develop improved ways to reduce ground control hazards in underground mining. Toward this end we present and compare results from numerical modelling and micro- seismic monitoring studies conducted at several different mine sites. Emphasis is on integrating results obtained with these tools to characterize, and thus increase our understanding of, important mine deformation processes. The ultimate goal is to use this knowledge to design mine structures, and develop mitigation measures, that minimize specific ground control hazards.

By B. D. Sartwell

The formation of alloyed regions near the surface of metals using ion implantation is being investigated by the Bureau of Mines as a means of providing corrosion resistance using much smaller amounts of the strategic alloying metals. Two ion implantation systems that can implant low-energy chromium, nickel, or aluminum ions into low-cost substrate materials such as iron or carbon steel have been designed and constructed. The development of the ion source, ion beam acceleration stage, mass analysis system, and target chamber are described in detail. The ion-implanted alloys have been characterized using proton-induced x-ray emission to give the total number of atoms implanted and to determine the extent of any surface contamination introduced by the ion implantation process. Research conducted at other laboratories on metallurgical applications of ion implantation is given.

Jan 1, 1980

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967

By Richard L. D?Arcy

This paper describing the mining practice and methods at the United Verde Extension mine, Jerome, Ariz., is one of a series of papers in preparation by the Bureau of Mines presenting the mining methods used in various mining districts of the United States. The United Verde Extension mine is a massive, high-grade deposit of copper sulphide containing some gold and silver and is mined almost exclusively by the conventional square-set method with some local modifications. About 450 men are employed underground and 1200 tons of direct smelting ore is produced per day. Figure 1 is a surface map of the Jerome district.

Jan 1, 1930

By J. Bruce Clemmer

[Gypsum is one of the most important nonmetallic c minerals, as is indicated by the fact that the United States consumed approximately 3,500,000 tons of natural and calcined gypsum in 1937. The building trades were the largest users required 2,520,000 tons of calcine for production of plaster, wall board, tiles, block, and various other insulating and building materials. The glass and ceramic industries and other manufacturers required an additional 126,000 tons. The balance was used in the uncalcined condition as retarder in Portland cement and or agricultural purposes.]

Jan 1, 1941

By Ivette E. Torres

The final 26 tables of this chapter, tables 24-49, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Mainly because of the separation of the countries that formed the U.S.S.R., the column that provided a 5-year average, was deleted. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1992. This group of tables now includes each of the top 19 crude minerals in 1983 in terms of value of their output plus 3 others of lesser rank. These 22 crude mineral commodities accounted for more than 98 % of the estimated value of world crude mineral production in 1983. Coal production, included in the 1983 value of production table as two separated entries, is combined in one table in this chapter. World output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1994

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933. Yearly reports6/ on the results obtained since the beginning of the survey have been published. The method and procedure of conducting the survey in 1936 were the same as heretofore.

Jan 1, 1938

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933. Yearly reports6/ on the results obtained since the beginning of the survey have been published. The method and procedure of conducting the survey in 1936 were the same as heretofore.

Jan 1, 1938

1. A total of 14,413 mining operations reported employment to the Mine Safety and Health Administration (MSHA). Nearly half (48.9%) were sand and gravel operations, followed by stone (28.5%), coal (14.7%), nonmetal (5.7%), and metal mines (2.1%). 2. Mine operators reported 240,000 full-time equivalent workers1 (down 3.9% from 1999). Independent contractors reported 42,000 full-time equivalent workers working on mine property (up 8.6% from 1999). Coal operators accounted for 26.8% of reported employee hours, followed by stone operators (25.9%) and sand and gravel operators (12.1%). 3. Eighty-four (84) work-related mine fatalities occurred in 2000 compared to 90 the year before. •The mine fatality rate was 29.8 per 100,000 full-time equivalent workers compared to a fatality rate of4.6 per 100,000 employees for all private industry. •Thirty-one percent (31%) of the fatalities occurred in underground work areas, which account for only17% of total employment. •Although the largest number of fatalities (28) occurred among miners who work for coal operators, coal contractor employees had the highest fatality rate (61.1 per 100,000 full-time equivalent workers). 4.There were 10,839 nonfatal lost-time injuries reported to MSHA, occurring at a rate of 3.8 injuries per 100full-time equivalent workers, and resulting in a total of 417,918 lost workdays.2 •Among all employees,3 the highest injury rate occurred among coal operator employees (5.6 nonfatal injuries per 100 full-time equivalent workers). •The highest percentage (34.7%) of nonfatal lost-time injuries were due to handling materials (e.g., over-exertion in lifting, pulling, or pushing objects), which also accounted for the greatest percentage of lost workdays (29.3%). •Among the most frequently occurring injuries, the most severe (as measured by the median number of days lost) were associated with accidents involving falls of ground, the use of powered haulage, and slips or falls. •The most frequently reported part of the body injured was the back (22.9% of all injuries). Back injuries accounted for the highest percentage of lost workdays (21.6%). 5.Seven hundred sixty-seven (767) cases of occupational illness were reported to MSHA. •The most frequently reported illness was repetitive trauma, resulting in joint, tendon, or muscle inflammation or irritation (37.3%). •There were 155 (20.2%) illnesses reported as hearing loss. The majority (68.4%) of hearing loss cases occurred among surface workers. •Coal workers' pneumoconiosis accounted for 14.5% of reported illnesses.

May 15, 2002

By E. M. Frost

"Helium has great value to the oil and as industry as a tracer gas, according to tests just completed in the Elk Hills Field, Naval Petroleum Reserve No. 1, Kearn County, California. When used as .a tracer gas, small percentages of helium are mixed with natural gas pumped into a reservoir for conservation, repressuring, or cycling purposes. Because minute quantities of helium added to natural gases can be detected by analytical methods and accurately determined, the variations of the helium content of gas withdrawn from various parts of a field when helium has been added to the injected gas give interesting and long-sought data on the movement of injected gas through reservoirs.The Bureau of Mines engineers began their studies of the use of helium as a tracer material in gas-injection operations in the Elk Hills, California, oil field, Naval Petroleum Reserve No. 1, in response to a request by the Navy Department for assistance in connection with an expanded oil-production program instituted in that field. This report discusses the Bureau's work on the problem of determining the direction and extent of migration of injected gas in the Elk Hills reservoir by the use of helium as a tracer gas,The Bureau appreciates the cooperation and assistance of Commodore W. G. Greenman, U.S.N., director, and Commander R. Walling, U.S.N.R., Assistant director, Naval Petroleum .and Oil Shale Reserves, Washington, D. C., Captain H. P. Stolz, U.S.N.R., commanding officer, and Commander F. G. Taves, U.S.N.R.., of the Navy's Elk Hills staff. The Bureau also appreciates the cooperation and assistance given by V. O. Wankowski, F. C. Tratt, Marray Putnam, Dana Champion, and other personnel of the Standard Oil Co., of California, operators of the Elk Hills field.R. A, Cattell, chief, and C. C. Anderson, assistant chief, Petroleum and Natural Gas Division; C. W. Seibel, supervising engineer, Bureau of Mines Helium Plants; and H. H. Hinson, petroleum engineer - all of the Bureau's staff - furnished valuable advice and assistance during the course of the work. H. C. Miller and G. B. Shea of the Bureau's San Francisco Office contributed valuable liaison work. The writer wishes to express appreciation to all these people for their cooperation and assistance."

Jun 1, 1946

By Harold M. Smith

The data in this report were prepared to show how Bureau of Mines routine crude oil analyses could be used to evaluate crude oils in terms of common commercial products . The use of Bureau of Mines routine analyses to determine hydrocarbon - type relationships for the gasoline and gas - oil fractions is demonstrated . For this purpose the correlation index , the aromatic profile and the naphthene profile are used to establish reasonably acceptable values for hydrocarbontype relationships . The derivation and meaning of these indications are discussed . These analytical interpretations are applied to a group of high - sulfur crude oils from the Near East , the Permian basin of West Texas , Venezuela , Colombia , California , and other locations , and the resultant data for gasoline , gas oils , lubricating oils , and asphalt are compared by appropriate tables and graphs . Because the Near East crude oils contain higher quantities of paraffins in the gasoline and gas oil ranges , they will yield good , lowsolvency solvents and good kerosine , jet fuel , and diesel fuels , but straightrun gasoline of inferior quality compared to similar products from either West Texas or Venezuelan high - sulfur oils . The Near East oils also should be good sources of lubricating stock . However , when used as stock for catalytic cracking or reforming , the Near East oils suffer by comparison because they are deficient in naphthenes .

Jan 1, 1964

By R. J. Fantel

The Bureau of Mines investigated the resource potential of 201 mines and deposits in 28 market economy countries and 17 mines and deposits in the U.S.S.R. and China. The 201 mines and deposits evaluated from market economy countries contain an estimated 34.2 billion metric tons of recoverable phosphate rock (at the demonstrated resource level), with Morocco and Western Sahara accounting for 61% (21 billion tons), followed by the United States with 19% (6.4 billion tons). The 17 mines and deposits evaluated in the U.S.S.R. and China contain approximately 1.5 billion tons of potentially recoverable phosphate rock. Potential annual capacity from low-cost, high-grade producing mines in the United States is estimated to decline significantly during the latter half of the next decade, and the United States will have to develop new, higher cost, lower grade mines in order to satisfy demand into the next century. Of the world's new production capacity which could likely be developed over the next decade, slightly over one-third could be produced at an estimated 1981 cost of $40 per ton or less, and about two-thirds would cost in the $40 to $50 range (including a 15% rate of return). In comparison, moot of the competing phosphate rock from producing mines in Morocco could be produced for under $40 per ton. The United States has sufficient demonstrated resources of phosphate rock (plus huge quantities at the identified and hypothetical resource levels) to satisfy domestic consumption for many years to come, but its future ability to compete in the major export markets against low-cost competitors is much more uncertain.

Jan 1, 1984

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974