Search Documents

By H. R. Shell

The work on synthetic mica and related subjects is being reported in a series of technical articles (see Supplementary Bibliography), each of which describes some special aspect of the subject. This is the final report on chemical analysis of the fluoride-containing silicates. A condensation of this report has been published (26).3/ Chemical analysis affords one of the best means of ascertaining the final com-position of either a heterogeneous mass or a single pure crystal, particularly where some constituents may be volatile. The analysis of fluoride-containing silicates was not so well known or understood that highly accurate results were commonplace. For example, on synthetic mica a university laboratory reported 11.6 and 9.2 percent fluoride when at least 13.3 and 11.3 percent were present, respectively; a commercial testing laboratory reported 9.14 percent as compared to 12.6 percent; and a glass company reported 7.0 percent as compared to 9.0 percent present. No intimation is made that these analysts could not have done better, but the point to be stressed is that the methods in use were long, tedious, and generally required a certain familiarity for best results.

Jan 1, 1956

By Frank K. McIntosh

Bauxite was first discovered in Tennessee, at Chattanooga, in 1906, during the construction of' the McCallie Street tunnel through Missionary Ridge. Several years later, bauxite was found in sinking a well on the Perry or Isabella Stewart property. These and other deposits furnished a substantial tonnage for the abrasive and chemical industries during the years 1906 to, 1920. The search for domestic sources of war material prompted by World War II brought the Tennessee bauxite deposits to the attention of the Bureau of Mines. During the summer of 1942, James S. Cullison and E. Godwin, geologists of the United states Geological Survey, made a survey of the bauxite deposits of the area. In August 1942, Harold B. Ewoldt, a Bureau of Mines engineer, accompanied by the Geological Survey party visited the area and a drilling program was prepared. Drilling was started in November 1942 and continued until March 1943. A total of 2,519.5 feet in 38 holes was drilled on three properties.

Jan 1, 1949

By Curtis A. Jones

Continuing interest has been shown in developing processes for extracting nickel and cobalt from low-grade domestic deposits of these metals and in improving existing methods. Of special concern is the nickel-recovery installation at Nicaro, Oriente Province, Cuba, operated for the General Services Administration. The Bureau? of Mines felt that a bibliography would help familiarize personnel at various Bureau of Mines stations and General Services Administration contractors with extraction methods both in the United States and in foreign countries. When this task was under way it became apparent that to compile a complete bibliography would require considerable time, so it was decided to limit the first part to the later literature and issue it independently, thus making it available sooner. The present work supplements the first part and extends the coverage to the earliest years of nickel and cobalt metallurgy.

Jan 1, 1959

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. at the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief summary of such costs as are available for publication.

Jan 1, 1965

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. ar the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief summary of such costs as are available for publication.

Jan 1, 1965

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth's crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930

By Steven K. Ruggieri

This report describes the operation and maintenance of the Mobile Inert Gas Generator for use in the Remote Sealing System for fighting underground coal mine fires. Seals are emplaced in mine passageways between the fire zone and the rest of the mine isolating the fire zone from the mine. The seals consist of fly ash that has been pneumatically conveyed via inert gas through a borehole connecting the surface and the passageway, Inert gas is used as the fly ash seal transport medium (instead of fresh air) since the introduction of large volumes of fresh air in the vicinity of the fire zone would be undesirable. The inert gas generation equipment is mounted on two flatbed trailers, the "hot" trailer and the "cold" trailer. The hot trailer contains the combustion and cooling equipment. The cold trailer contains the moisture removal and compression equipment necessary to convey the fly ash. The system is self-sufficient and requires only fuel and fly ash deliveries. The Inert Gas Generator has been thoroughly performance tested and has been operated in the field for approximately 200 hr. The system was employed in the demonstration of the entire Remote Mine Sealing System at the Jenney Mine in the Fall of 1978. The system is currently available for fighting any future underground coal mine fires.

Jan 1, 1980

By FRANKM. SEIBERT, G. G. Oberfell, GEORGEA. BURRELL

The Bureau of Mines is conducting a series of investigations with the common aim of minimizing the losses that occur in the mining and treatment of mineral substances. The results of the investi- gations are being published in reports of the bureau. This report treats of a method of preventing some of the waste of the natural gas incidental to oil mining. This method, the condensation of gasoline from natural gas, offers to the oil operator and others a profitable means of utilizing some of the oil-well gas now being wasted. The most desired constituent of crude oil is obtained, the production of oil is not hindered, and the gas, after the extraction of gasoline, can be returned to the leased area to drive pumps or into pipe lines for uses to which natural gas is ordinarily put, usually with its fuel value lessened only in slight degree. Publications already issued briefly discuss the subject. In this report the work is treated in greater detail, and the results of many additional tests are shown.

Jan 1, 1915

By William W. Adams

The quarrying and related industries of the United States improved their safety record in 1938 by reducing their accident-frequency rate to a lower acid more favorable position than it has occupied at any time except 1935 since comparable accident statistics became available in 1916. The rates for 1935 and 1938 were identical. The number of men employed in 1938, although smaller than in 1936 and 1937, was larger than in any other year since 1930. Volume of employment, as measured by the number of man-hours worked in the industry as a; whole, likewise was larger than in any year since 1930 except 1936 and 1937. Reports from operating companies to the Bureau of Mines, United States Department of the Interior, showed that 77,497 men were employed in 1938, a decrease of 6,597 compared with 1937. This figure represents the average number of employees for the period during which the quarries and plants were active during the year, which in 1938 averaged 223 workdays per employee compared with 241 in 1937. A total of 17.3 million man-days or 133.8 million man-hours of work was shown for the industry as a whole, which indicated a weighted average of 7.75 hours per man-shift. Reports for 1937 showed a total of 158.3 million man-hours for the entire industry and an average workday of 7.81 hours. Accidents resulted in the death of 82 employees, 5 more than in 1937, and in 5,027 nonfatal injuries involving disability for more than the remainder of the day on which the injuries were received. The number of nonfatal injuries was 1,321 less than in 1937. As the number of deaths and injuries was reduced more, proportionately, than man-hours of employment, the accident-frequency rate per million man-hours of work declined, the rate for 1938 being 38.19 compared with 40.59 for 1937. In other words, accident occurrence to the average employee was 6 percent more favorable in 1938 than in 1937 on the basis of actual number of accidents and actual number of man-hours worked during the 2 years.

Jan 1, 1940

By M. H. Kline

The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss, in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve) elongated to the north, approximately 26 miles in length. The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N.C., to the Hcupscup Knob prospects in Carter County, Tenn. The deposits were worked at least us early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.

Jan 1, 1948

By Wils L. Cooley

Several aspects of mine safety grounding systems and equipment are studied. Electrolytic corrosion of test ground beds has shown a high incidence of stray current damage, while efforts to build a reliable continuous ground bed monitor continue. Laboratory and field investigations of trailing cable splices have yielded strong evidence that splices can contribute to stray current problems in the mines, but a method is suggested for discovering deteriorating splices before they pose a serious hazard. A prototype device has been constructed to evaluate the electrical resistance of rail bonds underground as a source of stray current. Theoretical modeling of ground electrodes, has advanced considerably, now covering measurements of large cylindrical electrodes, multiple-rod ground beds, rod electrodes in stratified earth, and measurement of connected beds. A prototype instrument design is given for a potential gradient plotter to quickly evaluate voltage gradients near earth electrodes. Additional ground-check monitor testing is reported.

Jan 1, 1977

By Steven J. Schatzel

Large-scale methane releases in dual salt mines have resulted in ignitions and mine fatalities as recently as 1979. Several past studies have implied that hazardous methane occurrences in U.S. salt domes are distributed neither uniformly nor randomly, but are geologically controlled and potentially predictable. A first step by the Bureau of Mines in addressing the problem of methane in deal salt mines required development of a new test to determine volumes of gases in solid salt samples. This report considers the results achieved when 80 deal salt samples were tested for gas content by dissolution in a controlled atmosphere chamber. Criteria were organized to delineate salt types based on geological occurrence. Outburst samples range from 0.014 to 7.4 cm3 CH4/100 g NaCl, anomalous salt samples from 0.0027 to 2.6 cm3 CH4/100 g NaCl, and normal salts from less than 0.0003 to 0.31 cm3 CH4/100 g NaCl. The presence of higher hydrocarbons was most common in samples containing larger quan¬tities of methane. The presence of higher hydrocarbons appears to be useful in detecting methane hazards where some methane may be lost before gas content testing. An exploratory rotary and/or core drilling program, dissolution testing for gas content, and up-to-date geologic mine napping could allow a mine operator to assess methane hazards in dual salt.

Jan 1, 1984

By Frank E. Cash, John A. Johnson

"INTRODUCTION During the 6-year period, 1940-45, 481,485,000 gross tons of iron ore was shipped from the Minnesota, Michigan, and Wisconsin mines of the Lake Superior district. Approximately 367,000,000 tons, or 76 percent, of this ore was shipped from open-cut mines. The production of this large tonnage of iron ore from the open-cut mines of the Lake Superior district during the recent war was an outstanding achievement. It is questionable whether this record-breaking tonnage of iron ore, vitally needed for the successful prosecution of the war, could have been produced without the modern equipment and mining methods used in the district, The transportation of iron ore from the open-cut mines of the district is the most important phase of the mining cycle. Although some of the mines still use rail haulage advantageously, this method of haulage has been replaced at most nines with motor-truck haulage or a combination of motor-truck and belt-conveyor haulage.SCOPEThe transportation of iron ore in this report covers (1) power shovels, (2) rail haulage, (3) trucks, (4) belt conveyors, (5) shipping pockets, (6) accident statistics, and (7) safety rules pertaining to open-cut transporta¬tion. The purpose of the report is to discuss briefly and disseminate to the mining industry the modern methods, equipment, and safety practices used in transporting iron ore at the open-cut mines of the district.The 25 open-cut mines covered herein, located in the Marquette, Cuyuna, and Mesabi iron ranges of Michigan and Minnesota, shipped approximately 44,000,000 tons of iron in 1945, which amounted to 72 percent of the open-cut iron ore shipped from the Lake Superior district."

May 1, 1948

By James L. Elder, J. P. Capp, James J. Dowd

The Bureau of Mines and the Alabama Power Co., jointly, conducted the first experiment undertaken in the United States in underground gasification of coal in place, at Gorgas, Ala. Milton H. Fies, manager of coal operations, Alabama Power Co., proposed the cooperative investigation to Arno C. Fieldner, chief, Fuels and Explosives Branch, Bureau of Mines; and assisted in supervising the experiment. The objectives of the experiment were to determine whether coal in place could be burned successfully and whether the burning could be controlled; the effect of the fire on the coal bed and the overlying strata; and the yield and quality of gas that could be obtained.

Aug 1, 1947

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944