Search Documents

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

By Charlie Wyche

The British Solomon Islands Protectorate continued developmental work on bauxite deposits on the Islands of Rennell and Vaghena. A feasibility study was completed by Mitsui Mining & Smelting Co., Ltd., and Pacific Aluminum Ltd. (a subsidiary of Conzinc Riotinto of Australia Ltd,), and negotiations with the Government were in progress. The Government will receive a 25% share if the project is realized. It was estimated that the Islands contain 60 million tons of bauxite with an alumina content of 45% to 50%.

Jan 1, 1980

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By D. Harrington

The experience of the past 2 years has demonstrated clearly that mine explosions with heavy loss of life can be prevented. The investigations of the Safety Division of the United States Bureau of Mines disclose that during the fiscal year 1934 there were only 28 deaths from mine explosions in the United States, and during the fiscal year 1935 there were 54 deaths, a very favorable reduction when compared with an average death toll of 265 from this cause during the 20-year period prior to 1929. Although the frequency of occurrence of explosions has not decreased greatly during the past 7 years, there has been a marked decrease in severity, indicating that the coal-mining industry is taking more effective precautions to prevent the spread of explosions. A number of large coal-producing States, which in past years have experienced numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 5 years or even longer. A study of several hundred mine explosions occurring in the United States during the past 10 years or more indicates that the factors mainly responsible for these explosions are inadequate or defective ventilation and disregard of the hazards from explosive gas. Both of these factors are subject to control, and if controlled it is safe to say that deaths from explosions would be reduced to a negligible number as relatively few explosions are now initiated by dust.

Jan 1, 1936

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

Severe whipping of shuttle car trailing cables occurs when the car stops suddenly or reverses direction. This causes cable damage, and can seriously injure personnel near the cable. FMC has contracted with the U.S. Bureau of Mines to design, build and demonstrate a reel control system that will significantly reduce or eliminate whipping. II. CONCLUSIONS Results of engineering effort show that the following conditions are primarily responsible for the whipping problem. Causes may exist individually, or in combination.

Jan 1, 1972

By D. Harrington, G. S. Rice, R. R. Sayers

"The Bureau of Mines in Serial No. 2606,4 issued in May, 1924, gave tentative specifications for rock-dusting to prevent coal-dust explosions in mines. Subsequently, a sectional committee of the American Engineering Standards Committee was appointed to formulate recommendations for standard practice in rock-dusting coal mines. The report of this Committee which follows was approved by the American Engineering Standards Committee, December 30, 1925. Several members of the Bureau of Mines staff served on this Sectional Committee and its recommendations are essentially in harmony with those of the Tentative Specifications in Serial No. 2606.As certain explanatory details contained in that serial are not included in the recommendations formulated by the American Engineering Standards Committee, it should be considered by coal-mine managements in conjunction with the committee's report which follows:Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions 1. Definitions of Terms Used: The term ""Mine"" shall include all underground excavations from which coal is hoisted or transported to the surface, through one or more openings.The term ""Main Haulage"" shall include all underground slopes and planes, all rock tunnels, and all entries excepting those from which rooms or chambers are turned.The term ""Entry"" shall include all underground haulageways, travellingways and airways, excepting working places as defined below:"

Mar 1, 1927

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.

By M. W. Von Bernewitz

Fay's glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau's publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By Gregory M. Molinda

Extremely difficult ground conditions were encountered in the main belt entry in a room and pillar mine in West Virginia. Several generations of supplemental support, including cable bolts, cribbing, and Heintzmann jacks and beams failed to halt roof falls that threatened workers safety and the life of the mine. Polyurethane (PUR) was injected into 27 intersections in the roof and the results were monitored by borehole video camera. The mine had averaged 2-3 falls in the beltway per year and, since the roof injection, no roof falls have occurred. Pre- and post injection monitoring of test holes showed that stability can be achieved without filling all of the existing void spaces. Video logging showed that the project goal of building a beam from 2-6 ft into the roof was successful. Pre-injection monitoring of roof fractures uphole can delineate the zones to target for reinforcement, and avoid pumping PUR into large voids to little effect. Multiple-injection zones can be identified, and the entire intersection drill hole array can be optimized based on knowledge of the fractured zones. In addition, pre-monitoring can prevent excessive hydrofracturing in solid zones. Polyurethane injection is a proven method of rock stabilization in even the weakest, most broken ground. Optimization of the injection design by pre-injection video diagnostics can greatly contribute to the successful and efficient roof stabilization.

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"""Rock-dust barriers""5 as they are termed in this country, are for the purpose of confining a coal-dust mine explosion to the limited area in which it originates. These barriers were first tested in 1910-1911, with favorable results under the conditions of test, at the French official gallery which was then at Lieven, Department of Pas-de-Calais. Shortly afterwards the Bureau of Mines in the course of its investigation of all practical explosion-prevention methods tried barriers in the Experimental Mine near Bruceton, using the primary form of simple fixed cross shelves 20 inches wide extending over the passageway and laden with rock-dust. The Bureau termed them “Taffanel barriers"" in honor of the director of the Lieven testing station. The trials were made in conjunction with tests of explosibility of different coal-dusts.Experience showed that although the principle of barriers had merit when they were used for secondary defence, the primary form was uncertain in effectiveness. This led the senior author to design mechanically discharging barriers to be operated by the compression air waves which precede the flame of an explosion. For the better understanding of the principal involved, it is pointed out that the advance air waves are what make a coal-dust explosion possible by stirring up the coal-dust from the walls and floor of the passageway. If a barrier can throw inert dust into the air to form a cloud as dense or denser than that formed by the coal-dust, it will neutralize the explosiveness of the coal-dust, and the flame of the explosion will be extinguished. When the flame ceases, the pressure dies away in a short distance if the 'area that had been traversed by the explosion is not large."

Jan 1, 1930

By Stephen C. Tadolini, Raymond A. Mazzoni

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these “simple” devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors’ opinions of course).

By J. R. Allsup

Air pollutants in exhaust gas produced from LP-gas (propane) were studied using both laboratory engines and vehicles. The objective of the study was to evaluate engine parameters relating to the advantageous use of propane as a low-pollution fuel. Some comparisons are made between gasoline, natural gas, and propane. Results show that engines can operate over a wider range of A/F with minimum carbon monoxide and hydrocarbon emission when using propane than when using gasoline. Mixture enrichment using propane is unnecessary during cold starts, thereby eliminating the emission penalty during warmup. Carbon monoxide and hydrocarbon emission using propane are unaffected by ambient temperature. The photochemical reactivity of hydrocarbon emission is considerably lower with propane than with gasoline.

Jan 1, 1972

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts