Search Documents

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700° F.

Jan 1, 1996

By Richard L. Ash

A question that frequently arises during litigation concerned with accidents or alleged damages involving blasting is "were the explosives used according to the best known standards"" The question is not confined to only law suits, however, but also everytime poor blasting results occur. Unfortunately, general guidelines that can be used to define what may be considered as proper practice have not been established by any responsible body upon which to base a reliable Judgment; more often than not decisions are made primarily according to personal opinion.

Jan 1, 1975

By Donald H. Matthews

Drilling and blasting is an every day, sometimes routine activity, that is always fraught with catastrophic capabilities. Under the best conditions it is hazardous, time consuming and expensive. Under the worst conditions it may be impossible to perform by any but the most skilled specialists. Under all conditions drilling and/or blasting jobs are relatively difficult and require specialized equipment, materials and skills that are uncommon. This paper reviews some-of the jobs and problems handled by one drilling and blasting specialist to show the many varied types of problems requiring the services of specialists.

Jan 1, 1976

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By R Malo, A Yetter

The use of large diameter blastholes for underground mining began approximately twelve years ago and are now routinely employed in a variety of ore types and stope designs. These large boreholes, ranging in size from 4 1/2 inch to 8 inch diameter, were first utilized in the same fashion as in open pit bench drilling. However, a variety of changes quickly followed in order to accommodate the unique conditions encountered while using a blasthole sloping method.

Jan 1, 1984

By Dale Ramsey

Located in the Chestnut Ridge Mountains of Southwestern Pennsylvania, the Casparis mine named for the founder Kenneth Casparis operated from 1916 until the early 1950. producing crushed stone for construction and railroad ballast. The rock was transported by aerial buckets to a railroad tipple nearly 1000’ (304.80 meters) below the mine. The mine property is now owned by the Pennsylvania Game Commission and is located in the Loyalhanna limestone seam with 4 primary entries that are approximately 40’ (12.19 meters) high by 30’ (9.14 meters) wide and extend over 2 miles (3.22 kilometers) into the mountain.

Jan 1, 2006

By Ethan Steward, Robert Eades, Kyle Perry

Shock tubes, either gas or explosively driven, are often used for physical modeling of free field explosions or arena testing. The use of shock tubes often requires less setup time of subjects and smaller driving forces to create pressure versus time waveforms similar to that of arena testing. However, the effects of the shock tube cross sectional geometry on waveform properties is uncertain while free field explosion wave propagation and estimation is well studied.

Jan 1, 2018

By Lewis L. Oriard

This paper describes the process of developing blasting specifications for 850 miles of new pipe trench running parallel to an existing high-pressure gas pipeline, often with as little as 14 ft to the existing pipeline trench. The primary method of preventing damage to the existing pipeline was the use of fracture (overbreak) control.

Jan 1, 1994

By L D. Lawrence, W B. Sudweeks, J Bailey

Modern era urbanization is presenting at least one category of explosive consumers with a growing concern for ecological and environmental problems associated with their blasting processes. The construction industry is now, more than ever, being closely monitored with regard to its use of high explosives. In particular, contractors excavating the countless thousands of miles of various trench lines required for virtually every major new construction development taking place in America are being more closely scrutinized by local, state, and federal authorities with regard to blasting practices.

Jan 1, 1988

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By J. -P. Tshibangu, E. Lefebvre

ABSTRACT : The Tournai’s region in Belgium is characterized by outcrops of limestone that were mined out long ago by different companies for cement and crushed materials. The region is densely populated and the vibrations generated by blasts in the quarries are of big concern. The occurrence of electronic detonators and development of computer sciences brought a new expectation in controlling the vibration level and, hence, carry out bigger blast operations. In this paper we present the results of two experimental blast programs that have been carried out by the Nobel explosive Belgium Company on the Gaurain-Ramecroix quarry to understand the effect of the delay on the vibrations generated in the neighborhood. The first program has been implemented during the early use of electronic caps in Belgium (1996) by performing some unit shots. An attempt to model the effect of the production blasts by the hybrid method (Hinzen 1988) gave promising but poor results compared to infield measurements. A new program (more than ten blasts) has been implemented in 2006 in which the delay and blast firing sequence (i.e. the order in firing adjacent holes in a row) have been changed; a new attempt is made to build unit signals by deconvolution and then try to model production ones. A comparison of the two approaches is made.

Jan 1, 2008

By William Everett, Jack Eloranta

United Taconite is an iron ore mine operated by Cleveland-Cliffs Inc (Cliffs) located near Eveleth, Minnesota. The mine, originally known as Eveleth Taconite Mines, was purchased in December 2003 by Cliffs (70%) and Laiwu Steel (30%). The mine site, known as the Thunderbird Mine, produces taconite ore for delivery by rail to the company’s Fairlane plant, located approximately 10 miles to the south near Forbes, Minnesota. At the plant, the crude ore is ground, concentrated and processed into pellets for steel industry customers. Total pellet production capacity is about 5.4 million long tons (Ltons) per year.

Jan 1, 2006

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By Mark S. Stagg, Norman S. Smith, Rolfe E. Otterness, Stephen Rholl

Blast design parameters were studied in an attempt to quantify their relationship to rock fragmentation. The Bureau of Mines conducted a series of 29 reduced-scale shots at the University of Missouri-Rolla's experimental mine with bench size from 40 to 80 inches. Design parameters varied were burden, spacing, explosive diameter and stemming-explosive length. The shots had 3 or 4 blastholes fired at delays of 1-4 ms per foot of burden, based on previous tests that showed hole interaction could improve fragmentation by 12 to 20 percent over single-hole shots or simultaneous firing. All rock, 2000 to 23,000 pounds per shot, was screened and weighed to determine the fragmentation size-weight distribution.

Jan 1, 1991

By J Lyall Workman, Peter N. Calder

Operations using draglines to remove the overburden above coal seams have increasingly turned to cast blasting to improve productivity and reduce costs. Many such operations also employ active highwall pre- splitting to produce highwalls of well defined configuration, behind which the subsequent blast can be designed and implemented to maximize casting. In some cases isolating the block to be blasted allows water to drain out of the rock mass and provides the opportunity to use less costly explosives.

Jan 1, 1991

By David Leidel

A major characteristic that distinguishes modern society from its predecessors is the understanding that events are not driven by the whims of the gods, pre-ordained fate or nature, but are controlled to a greater or lesser extent by the actions, (or inactions), of people. The study of risk assessment is the basis for determining risk or the likelihood of an event occurring combined with the consequences of that event if it does occur. This study is indubitably linked to the mathematics of probability and statistics which permits the quantification of risk. As the Industrial Revolution significantly increased the exposure of persons to new types of energy sources, materials, equipment, and means of more rapid transportation of goods and people, quantitative risk assessment became a vital tool in protecting workers and the general public exposed to these new technologies.

Jan 1, 2007

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

This paper analyzes the blast design for lime stone quarries of two major cement plants in Pakistan. The production blast of these quarries was resulting in excessive boulders production. At some instances, the rate of boulders production was approximately 10%-15% of the main production blast i.e. if a round of main blast gave around 4000 tons of material; almost 400 to 500 tons of that material was in the shape of massive boulders. This gave rise to increased operating costs requiring boulders collection, drilling and secondary blast.

Jan 1, 2012

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Andre Pienaar, Larry Wilson

Destruction of waste emulsion by blasting has been proven to be risky and disastrous incidents have been seen when using this practice. Our R&D department in conjunction with Lake International has developed an emulsion breaker system where underground waste can be destroyed safely. The methodology and logistics around the system will be demonstrated during the presentation. This process offers a safe alternative for the removal of sensitized and un-sensitized waste products from these mining environments.

Jan 1, 2010

By Sri R. B Singh

Based on CMRI investigations in nearly 50 mines, the authors have developed two empirical formulae for the effective determination of burden and spacing in any kind of rock deposit. Along with charge loading parameters, decoupling effect and bench height, the equations consider rock characterisation parameter by incorporating 'RQD' i.e Rock Quality Designation. The value of 'RQD' may be obtained either by core recovery using diamond drilling or theoretically from the characteristics of joints or bedding planes. The derived equations may be used in any rock mass under varying geologic and charge loading conditions. The Formulae suggested herein, are explicit, simple in form and easily applicable in field purposes. The values obtained from the present equations are verified against various field data generated by CMRI during the past several years.

Jan 1, 1998