Search Documents

By Sam Oaks, David A. Smith

The new Corridor "G" Federal Highway Project in Logan County, West Virginia is the largest mass excavation highway project currently being built in the United States. Seven sections covering 14 miles of four lane highway and two connector roads will require over 30 million cubic yards of excavation. Construction is on a fast track schedule requiring the contractors to complete excavation and pavement placement in a little over 19 months. The two different general contractors have implemented several innovative Blasting and Excavation Programs to complete this project within the tight completion schedule. The paper expands on some of these unique programs that made the project a reality.

Jan 1, 1994

By Jason Rock, Rob Thompson, Lee Julian

Reactive ground is ground that undergoes a spontaneous exothermic reaction after it comes into contact with nitrates. This is commonly caused by inert rock hosting sulphide minerals, such as pyrites that act as the reagent. The presence and subsequent rate of reaction with nitrate based bulk explosives can be difficult to predict. Once identified, only explosives that are tested and proven to be compatible with the reactive ground may only be used. These typically take the form of inhibited ammonium nitrate emulsion blended with a limited volume of ANFO or porous prilled ammonium nitrate (PPAN) to ensure that all AN prills in the blend are wholly encapsulated and thus protected from the reactive ground. The requirement for high emulsion content bulk products limits the suite of products available for use to high energy, and high expense products. Further, if chemically sensitised products are used, charged holes must be left unstemmed to allow for gassing to occur, adding delay and exposing the blast crew to an unconfined charge in reactive ground. A range of inhibited products has been developed that are solid sensitised and can be bulked to as low as 0.9 g/cc (56.2 lb/ft3). The use of a solid sensitiser enables stemming to occur immediately after each hole is charged, confining any unplanned detonation more safely within the rock mass. The effective and precise manufacture of bulked inhibited products required a new and innovative Mobile Processing Unit (MPU) design. This MPU required the ability to blend two solid raw materials (AN prill & sensitiser) along with two liquid ingredients (AN emulsion and process fuel). This MPU has been designed, manufactured and has used successfully to manufacture low density inhibited explosives. This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

By William A. Travnik

For more than 60 years, ESSO RESOURCES CANADA LIMITED has been producing and refining oil at a small refinery in Norman Wells, Northwest Territories, and supplying diesel fuel and other oil products to northern markets. In 1982,ESSOwas granted governmental approval to expend production from the oil field from 475 cubic metres a day to 4400 cubic metres a day. This $800,000,000projectproceeded ahead of schedule for a start up in 1985.

Jan 1, 1986

By D. Mason, W. J. Birch

Blasting operations are arguably one of the most contentious areas of surface mining.Many operators carry out outine monitoring as required by Mineral Planning Authorities. However in so doing they only concentrate on the observed Maximum Peak Particle Velocity (PPV) being below the statutory limit and pay little or no attention to the measurable parameters that determine this value (e.g. scaled distance, burden, detonator type, blast type or rock type). Such practice is “monitoring to comply”. What is needed is for the operators to adopt a methodology that clearly demonstrates to the appropriate regulators that the operator is “planning to comply”. The aim of the exercise being to deliver a process that is seen to be transparent, accountable, and quantifiable, which seeks to minimise environmental impact whilst not compromising the efficiency of the blasting operations mine.

Jan 1, 2011

By Emmett J. Ientilucci, Martin Held, Xuesong Liu

Mining is crucial for advancing technology and science by providing essential resources and materials. Quarry blasting, a necessary process in mining, releases these resources and chemicals, driving research and engineering improvements. However, NOx (nitrogen oxides) is an undesired contaminant produced during quarry blasts, posing a significant negative impact on mining activities. Therefore, detecting and quantifying NOx emissions is essential for designing effective blasts, analyzing their dynamics, and reducing contaminant production. Image processing and machine learning, including deep learning methods, have been applied to solve smoke plume detection and segmentation tasks. Most research has focused on smoke from campfires or forest fires, which are important for early fire and smoke detection. However, there is limited research on quarry blast smoke using machine learning methods, which presents challenges for recognizing the smoke plume from complex background scenarios and objects, including collapsed rocks, scattered soil dust and dirt, and the dynamic movement of the scene due to blast vibrations. Detecting NOx within the smoke plumes is further challenging because NOx must be distinguished from the overall smoke plume, as they share many common spatial features. To resolve this issue, we propose an ensemble method for NOx detection that combines smoke plume segmentation with NOx fume detection. First, we apply a smoke plume segmentation model to identify the smoke plume regions. Then, we use these masked-out smoke plume regions to detect NOx based on its unique color features. The first stage of the ensemble method helps block out complicated confusers in the background, such as reddish and brownish dirt. Next, we specifically design a color classifier for NOx to further improve its sensitivity. We evaluate the overall video-wise performance using accuracy, false alarm, and miss rates based on sampled image frames from videos. Additionally, we assess the mean Intersection over Union (mIoU) for smoke plume segmentation and the mean Average Precision (mAP) for image-wise performance from an algorithmic perspective. In summary, this paper represents the first attempt to apply machine learning approaches to NOx detection in a memory-efficient and time-efficient manner.

Jan 21, 2025

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

In the March/April 2006 issue of the Journal, we published an ethical dilemma called “Blowing the Whistle.” We received many interesting responses to the article as requested. Some of the responses are printed here. We’ve also included “Blowing the Whistle” again in this issue as a refresher on page 37. Dear Editor, It is in my own personal belief that it would be extremely important if I were the blaster to take the following steps. 1. Hold an immediate emergency meeting with the contractor to convince them to stop work at this point.2. This meeting would need to be held with all powers that be in this construction company. This helps eliminate the hearsay (excluding the farmer). 3. Explain the entire situation to the contractors as it has been presented to the blaster by the farmer. 4. Recommend calling in an engineering or geological firm with the expertise to investigate this matter immediately, and take all immediate action based on findings. 5. Follow up with farmer allow him to speak, (a.k.a. vent) and assure him proper steps are being taken to come to resolve this matter. 6. Be a good listener, and communicator with the farmer while investigation is being conducted. 7. Should the contractor not want, or take any of these recommendations, the blaster himself and his company should question even working for this company ever again. This in itself would not be the class of people we would want to be associated with EVER.

Jan 1, 2007

By Lon D. Santis

This paper describes a lightning warning system (LWS) in operation at the U.S. Bureau of Mines' (USBM) Pittsburgh Research Center (PRC) from December, 1989 to April, 1991. An electric field mill measured the DC atmospheric electrostatic field. Also, an economical on-line weather data service provided lightning location maps and other weather information. A system such as this can significantly improve the safety of explosive handling. The use of these two methods addresses the detection of thunderclouds building overhead and the prediction and tracking of developed storms. Warning reliability of the system was very good when data from both sources were considered. Experience showed, however, that use of either system alone would not provide adequate reliability in most situations. Some problems occurred with the field mill and there is some question whether the instrument is compatible with harsh mining environments or could be made portable. Another method ' of measuring electric field based on fiber optics is discussed. This technology may be able to overcome the problems with field mills.

Jan 1, 1993

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By L. M. Lopez, J. A. Sanchidrian

This work investigates the performance of some of the measurement techniques used in vibrations from blasting monitoring. Two tri-axial geophones with cases of different size, shape and mass were tested in a shaker table. The geophone cases were mounted in three different ways on a granite slab fixed to the plate of the shaker: freely placed, sandbagged, and anchored. A known horizontal periodic motion of constant amplitude, and frequency from 16 to 200 Hz, was applied to the slab. Two amplitude levels of 5 and 20 mm/s (0.2 and 0.79 in/s) were applied when the sensors were sandbagged or anchored and only 5 mm/s when no holding force was applied. The transmissibility of vibrations from the rock to the longitudinal geophone as function of the frequency (i.e. ratio of response of the geophone to the slab motion) has been obtained for each measuring condition tested. The transmissibility is considered a composition of the transmissibility of the rock-to-sensor coupling and the transmissibility of the sensor’s mechanics and electronics. The transmissibility of the coupling is obtained normalizing the total transmissibility with the transmissibility of the seismographs, obtained by a suitable test to which a coupling transmissibility of 1 is assigned. Geophone-to-rock coupling is a resonant phenomenon that may alter the amplitude of the measured waveforms by a factor of 1.2 to less than 0.6. The most accurate and precise measurements are obtained with geophones anchored to rock. On the contrary, freely placed or sandbagged sensors are non-predictable planting conditions that lead to high amplification or damping in most of the frequency band analyzed. It is also shown that existing acceleration criteria to select coupling methods do not necessary lead to good quality (accurate and precise) vibration data.

Jan 1, 2014

By A. S. Romphf, C. K. McKenzie

Recent full-scale field studies involving single-hole charges fired to free faces under a wide range of operating conditions have delivered precious insights into airblast characteristics and propagation. The field tests involved production blasthole diameters in the range 89 to 406 mm (3 ½ to 16 in), bench heights in the range 9 to 24 metres (30 to 79 ft), burden ratios (burden/hole diameter) in the range 14 to 51, stemming ratios (stem height/hole diameter) in the range 11 to 36, explosive types of ANFO, heavy ANFO and pumped emulsion, and both solid-column and double-decked charge configurations. Around 700 measurements of peak amplitude and wave shape were made in all directions (0 to 360 deg) from the free face, from 38 single-hole tests in nine North American operating quarry/mine environments. The most striking observations were the strong dependence on directionality of the wave propagation parameters and wave frequency, the consistency of wave shape which resembled the modified Heelan wavelet, and the occasional appearance of distinct, multiple pulses from single events, shown to be echoes/reflections from quarry faces. In-hole deck charging failed in this study to achieve expected peak overpressure reductions, with the peak overpressure levels in Pascals/psi/millibars being approximately 40% higher than the as-charged weights. Inter-deck delay times in excess of around 25 ms are required for effective reduction of peak overpressure levels from front-row holes. Simple linear-superposition models based on synthetic wavelets applied to large production blasts produce composite waveforms which capture the important features of the actual pressure-time history, and correlate well with measured waveforms.

Jan 26, 2026

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Julio Cesar Barbosa de Freitas, Rafael Gonçalves Araujo, Túlio Soares, Jair Koppe, Augusto Ferraz Ribeiro, Pedro Barreto Garcia

This study thesis was motivated by the fact that it is of fundamental importance for open pit mining that the slopes initially have a geometry in accordance with what is proposed in the mining planning. This occurs because an inconsistency in this design can impact the operational safety and economic solutions of the mining project. These consequences can be explained by the fact that rock blasting close to mining limits requires specific study due to the attention required. Because, when this operation is not carried out properly, the mining plan in the mine may not be respected and may create risks to the operation due to the presence of unstable blocks on the slopes (Mackenzie). In this sense, Mackenzie (2004) cites pre-split, trim blasting and buffer as commonly used explosive blasting techniques that aim to limit damage beyond the projected wall. Therefore, Enaex Brazil realized the need to better understand the pre-split method. To do this, it is necessary to understand how the energy released during detonation is perpetuated in the rock mass when this technique is used and when it is absent. Thus, this analysis is based on a seismic study that allows the creation of vibration attenuation laws and an elementary wave damage model, which allows the local characterization of the rock. With this model it is possible to relate the peak levels of vibration during blasting and the extent of damage, but a critical level of vibration (PPVc) and its relationship with the Uniaxial Comprehension Resistance (UCS) are also defined for the start of fracturing and its level (McKenzie et al, 1995). And, mainly, this work aims to address a way to measure the pre-split filter potential by comparing the attenuation law with and without pre-split, ultimately knowing whether this finishing blasting is being effective, to understand the pre-split filter capacity.

Jan 21, 2025

By AK Chakraborty, AK Raina

Burden of drill hole is third most sensitive parameter effecting the ground vibration in blasting apart from maximum charge per delay and distance. Various types of burdens can be seen in practical bench blasting situations. Burden can be expressed as drilled burden and initiation burden. Drill holes may have various front row burdens (toe burden), which may be different from the designed burden. In order to ascertain the impact of front row burden as well as the initiation burden on intensity of ground vibration and air overpressure experiments were conducted in sandstone overburden benches of an opencast coal mine and limestone quarry. Blast trials were carried out in cognisance of both drill and initiation burden while keeping all other parameters constant. Effect of front row burden was also extensively studied by keeping almost all other parameters constant. The results of the study reveal that there is substantial influence of front row burden on the vibration and air overpressure. The statistical analysis of vibration and air overpressure data with drilled burden and initiation burden gives significant evidence that the level of peak particle velocity of vibration (Vmax)) is reduced by reducing effective burden with modification of initiation. Data analysis carried out for air overpressure versus initiation burden shows that reducing effective burden with modification of initiation results in increasing the level of P. The study reveals a qualitative assessment of the influence of burden on the blast induced vibration and air overpressure. The study also recommends to modify the initiation pattern to reduce the effective burden in order to reduce the vibration, without disturbing the fragmentation.

Jan 1, 2004

By Dale Preece, Stephen Chung

The DMC-BLAST (Distinct Motion Code) has been developed for modeling bench blasting to one or two free faces such as choked blasting in surface gold operation and cast blasting in coal mining, respectively. This computer code has been used to assist the analysis of rock mass displacement after a blast was initiated in an orderly delay sequence. Applications of this feature can be found in the studies of dilution control in surface mining of gold as well as coal involving complex rock structures. Recently, DMC-BLAST has been modified to include a designated delay firing order coupled with variable rock strengths in the blasted media. This newly added feature allows the investigation of the effects of delay firing order on rock displacement in blasting a complex interbedded ore-waste structure. Examples of blasting a steeply dipping coal seams and bedded rock structure, especially in coal mining operations will be addressed and the comparison of efficiency in blasting in an up-dip as opposed to blasting in a down-dip direction will be discussed. Also covered in the paper is a new application of DMC-Blast to simulate a stope blasting underground. Simulations of blasting in a few selected types of timing/structure combinations will be presented in this paper.

Jan 1, 2000

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012