Search Documents

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By Kyle Bartholomew, Robert McIvor

"Functional performance analysis of closed circuit grinding provides valuable insight into the two components of ball mill circuit grinding efficiency: classification system efficiency and mill grinding efficiency. Classification system efficiency isolates the combined effect of classifier performance and circulating load ratio from other circuit variables, such as ore grindability and the mill grinding environment. Optimization of classification system efficiency ensures grinding energy is applied to particles needing further size reduction and not to overgrinding. Entirely based on size distribution data, classification system efficiency precisely distinguishes subtle changes in classification system performance. Use of the functional performance equation to isolate mill grinding efficiency allows for proper optimization of the mill grinding environment by isolating confounding effects of changes in classification and ore grindability. Variables such as mill percent solids and grinding media selection can be optimized using the mill grinding efficiency subcomponent of functional performance. First published by McIvor in 1988, the functional performance equation provides a set of standardized, quantitative optimization criteria, simple and powerful, which link circuit performance to plant design and operating variables that can be manipulated. Functional performance optimization has been applied in numerous mineral processing plants globally and continues to gain acceptance as a practical means for grinding circuit optimization. In this paper, examples of derivation and industrial application demonstrate the means by which functional performance analysis dissects grinding circuit efficiency into its subcomponents allowing the reader to apply this straightforward, powerful optimization methodology at their mineral processing operation."

Jan 1, 2014

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By J. Shibata

The behavior in electric field of fine particles present in aqueous solution was measured in order to apply to the classification of fine particles. The sample particles used are spherical polystyrene particles with the average diameter of 0.03 µm, 0.1 µm, 1.0 µm, 4.3 µm and 9.6 µm. Electrophoretic mobility and zeta potential of various particles are measured by an instrument based on the principle of the laser Doppler effect. The influence of temperature, electrolyte concentration on the electro-phoretic mobility was investigated for various polystyrene particles. The electrophoretic mobility increases with increasing pH and temperature of suspensions. The measured electrophoretic mobilities are different from electrolyte concentration and particle size. The electrophoretic retardation effect and relaxation effect are considered to explain the behavior of fine particles in electric field by applying the electro kinetic theory of Wiersema et al. For all particle size, the electrophoretic mobility decreases rapidly in high concentration of KNO3 such as 0.1 mol/dm3due to the compression of electric double layer The forces acting the particles in electric field are considered to be electrical force, friction force and some other forces like relaxation effect and electrophoretic retardation effect which appear in ionic behavior. It is considered that the particle moving velocity depends on the particle size. When the particle size is less than 1µm, the velocity increases with increasing the particle size. On the oth-er hand, the velocity deceases with increasing in particle size, when the particle size is larger than 1µm. This phenomenon is considered to be interesting from the viewpoint of classification for fine particles. We found that the electrophoretic mobility of 1.0µm particles is larger than that of 0.1µm particles, and that it is possible to classify fine particles by using the difference of electrophoretic mobility by many experimental results. The phenomena can be explained by the forces acting the fine particles in the electric field. We can apply the behavior to classification of fine particles.

Jan 1, 2014

By L. A. Vaisberg, E. V. Shishkin, S. V. Kazakov

"This research is targeted at finding solution to the problem of reduction of specific energy consumption during disintegration of solid materials with the help of machines, operating in a quasiresonant mode. The objective of the research is the development of an energy-saving method of disintegration of supestrong rock and by-products on the basis of vibrational units with two movable crushing elements, operating in a rigorous synchronous-antiphase mode without stringent kinematic links. In the course of investigations a mathematical analysis of the dynamics of vibrational units was performed to determine required mechanical parameters, allowing for adjustment of the machine actuating elements to high-frequency synchronous-antiphase oscillations in the quasiresonant frequency range. As a result of performed pilot tests, the reliability of desktop studies was confirmed and the dependency of process parameters on the machine regulated parameters in the quasiresonant frequency range was identified. The analysis of obtained data showed that during machine operation with cone-shaped crushing elements in the quasiresonant frequency range, the yield of the high-quality finished product (WFA grits of -3+1 mm grain size class) in one pass reaches 35%, whereas the form of the particles corresponds to the grain form with sharp edge. The quasiresonant operation mode of the vibrational unit with two freely suspended crushing elements (without stringent kinematic links) provided substantial reduction of energy intensity during crushing down to 0.16 kWh/t, which shows reduction of power consumption for crushing by more than 15% compared to conventional equipment.INTRODUCTION The most common and energy-consuming processes in the mining industry are the crushing and grinding of various solid materials. Such large energy costs are due to the fact that the capabilities of the existing crushing and grinding machines are based on traditional methods of destruction, and are limited by their kinematic features, which do not allow to reduce the energy intensity of processes, to lower the irreversible loss of useful components, to improve the quality of marketable products. In connection with the foregoing, the task of energy costs reducing for disintegration is one of the most important issues in the enrichment of both minerals and processing of man-made raw materials. The solution of this problem is possible only through the creation of a fundamentally new highly efficient technique and technology for processing raw materials [1, 2]. It seems that the greatest prospects in this respect are the vibration methods of disintegration, in particular, the vibratory cone crusher based on a two-mass system without rigid kinematic connections between the crushing bodies, with vertical vibrations of the working bodies. In this machine, the principle of rational material destruction is realized – crushing without re-grinding [3-5]."

Jan 1, 2018

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By V. Dementiev

Pyrite cinders is a complex raw material, in which the valuable metals are: Au(2.04 g/t), Ag(35.0 g/t), Cu(0.38%), Zn(1.1%) and Fe(56.0%). In this case high costs for mining and ore processing are not required. The hydrometallurgical treatment of pyrite cinders using thiourea, sulfite and cyanide solutions are examined in this paper. It was found that thiourea leaching is ineffective due to high consumption of thiourea and sulfuric acid. The cyanidation on pyrite cinders was conducted. Various options of the preparation of the products for the subsequent cyanidation have been examined. The tests on cyanidation process optimization were conducted. The effectiveness of these cementation methods by metallic iron or extraction for copper recovery from water phase has been shown. Zinc precipitation can be found in the form of carbonate. In order to recover noble metals from cyanide solutions, the cementation onto zinc dust was tested. The developed technology provides for recovery at 49-56%Au, 20-25%Ag, 22.5%Cu and 50%Zn during NaCN (1.4 kg/t) and CaO (6 kg/t) consumption. The results of pilot plant testing are the basis for technical regulations in order to design a pyrite cinders treatment plant. The technology has been examined in pilot-plant conditions. In this case the recovery of 54.5%Au, 45.3%Ag, 30%Cu and 49.9%Zn was achieved to provide saleable products. Keywords: pyrite cinders, thiourea leaching

Sep 1, 2012

By Jiongtian Liu, Guixia Fan, Caom Yijun

A cyclonic-static micro bubble flotation column (FCSMC) is an effective separation device for fine grain treatment. The separation of fine ilmenite by FCSMC was explored in this work. The influence of reagents dosage (regulator, collector and auxiliary collector), pulp density, circulation pressure and aeration quantity on TiO2grade and recovery wasinvestigated.The optimal conditions of a rougher are follows: pulp density 45%, pH 5.0, MOH collector dosage 2800 g/t, diesel oil dosage 700 g/t, circulationpressure 0.19 MPa, aeration quantity 0.8 m3/(m2•min). The optimal conditions of a cleaner are follows: pH 4.0, circulation pressures 0.16 MPa, and aeration quantity 0.5 m3/(m2•min).A pilot plant continuous test with a rougher-cleaner by FCSMC for 72 hours was proceeded under the optimum conditions. Compared with industrial flotation machines, the concentrate grade of FCSMC is 48.11% with an improvement of 1.08 percentagepoints, while the recovery is 82.36% with 13.64 percentagepoints increment. Moreover, the flowsheet is simplified from six parts (a rougher-two scavenger-three cleaner) in flotation machines to two parts (a rougher-cleaner) in FCSMC. Proofs were also provided by the analysis of the by-size grade and recovery of concentrate.Results show the FCSMC is an effective separation device to recover -74 µm size fraction.

Jan 1, 2014

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By E. V. Manlapig

"Some researchers postulate that the floatability of a particle in the streams of an industrial flotation circuit is a function of only its size and liberation properties. They do not discount the importance of reagent or surface contamination on particle floatability but assume that the reagent coverage or surface contamination of the particle surfaces is essentially uniform for particles of similar size and mineralogical properties when subjected to a particular chemical regime.In this paper, samples collected from batch tests performed on different streams of the Red Dog lead cleaning circuit have been characterised with respect to their size, mineral association and mineral surface exposure. An analysis of this data set indicates that particle recovery rate is significantly affected by mineralogical properties - in particular the degree of valuable mineral surface exposure.However, through the use of a nodal analysis technique developed by the authors, it can be concluded that particles with the same size and mineral composition do not all float with the same rate, but with a distribution of rates. The characteristics of this floatability distribution do not change during the flotation process. It is suspected that the particles within a size mineralogical class in this study have varying degrees of surface oxidation and that this results in varying particle flotation rates. Thus basing particle floatability on size and mineralogical effects, alone, in a flotation model is not always valid."

Jan 1, 2003

By Michael Young, Rodrigo Araya, Cesar Gomez, Le Huynh, James Finch

The performance of flotation machines is closely related to the gas dispersion characteristics achieved in their operation. It is known that frothers play a major role not only in the size distribution of the generated bubble population, but also on the swarm rise velocity. A program to characterize frother effects on two-phase hydrodynamics (air-water) of Jameson cells was undertaken in a fully instrumented pilot unit installed at McGill University. Gas dispersion parameters (gas velocity, gas holdup and bubble size distributions) of the gas-liquid mixture generated in the downcomer were measured after its release into the separation chamber. The unit was operated under different conditions including gas velocity, liquid jet velocity and frother concentration (MIBC). Bubble size distributions for concentrations above the critical coalescence concentration (CCC) were narrow with Sauter mean diameter between 0.6 to 1.3 mm. The bubble size followed the general trend as encountered in other types of flotation machines, i.e., rapid decrease with increasing frother concentrations below 10 µL/L, and almost no change in size for concentrations above 30 µL/L. The CCC was between 10 and 15 µL/L. Strong correlations were found between bubble size and air-to-liquid flow ratio (APR), and between the bulk density of the aerated solution in the separation tank and the vacuum inside the downcomer. An equation is proposed to estimate gas holdup in the separation tank from vacuum and bulk density readings.

Jan 1, 2014

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push to-wards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Some mineral waste can also be used, either as fillers or as reactive components. The use of waste-based geopolymers results in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the conversion or encapsulation of toxic waste, including radioactive waste, due to their chemical stability and resistance to acid attack. It is the aim of this paper to review recent developments on the science underpinning this ?green? technology, and to discuss the technical and commercial drivers governing the large-scale adoption of the technology. Some of the recent fundamental breakthroughs in the study of geopolymer technology at the University of Melbourne will be presented. Despite the complexity of this reactive sol-id-gel system, progress has been made in the development of a thermochemical reaction kinetic model that has been validated using both calorimetric data and synchrotron kinetic data. Geopolymerization is potentially a disruptive technology, so that it is normal to expect strong resistance from established companies in the construction materials industry. It is increasingly necessary that waste generating industries such as mining collaborate with industries such as construction that could utilize this waste. The world?s first full scale geopolymer plant utilizing waste and re-cycled material has been commissioned recently in Melbourne, Australia, so progress on commercialization will also be presented. The authors frequently present keynote lectures on geopolymer science and technology at materials science, ceramics and construction materials conferences. However, this interdisciplinary technology that is still in its infancy, deserves more attention in the mineral processing and mining industry in view of its potential use in the mining industry, and also in view of the importance of mineral processing techniques in recent advances in geopolymers.

Jan 1, 2014

By R. C. Miranda

This paper intends to demonstrate the applicability of tools for advanced process control and online particle size image analysis in crushing and autogenous grinding circuits. In a crushing plant, cameras are installed in the conveyor belts of the circuit products. The vision system continuously processes the acquired images and thus obtains the variation of the size distribution curve. From these measurements, the advanced control system can operate, for example, at the opening of the crusher, in order to keep the P80 in the desired range. In addition, through the power information and level of the crusher&apos;s chamber, it is possible to increase the capacity of the crushing circuit. If the crusher is not equipped with an automatic opening adjustment, a warning may be issued to the operator to provide this setting manually. In mineral processes that use autogenous and semi-autogenous grinding for fragmentation, obtaining online F80 through the vision system allows for manipulating the parameters of rotation speed and solids concentration, through which the amount of material at the critical particle size that is produced can be controlled. In addition, the noise produced in the mill can be measured and controlled. Thus, it is possible to prevent breaches and to optimise the mill capacity for grinding. Image analysis combined with an expert system that translates this information and acts to seek the most appropriate particle size distribution, brings greater stability to the process optimising the capacity of the equipment, which allows for significant gains in production.

Sep 1, 2012