Search Documents

By Bengt H. Fellenius

The design of pile foundations is much more commonly verified by means of a full-scale test, than is the design of other foundation units. The reason is not that our knowledge of pile behavior is more uncertain than our knowledge of other foundation types making the verification necessary, but more that the loads in a structure are more concentrated to single foundations in a structure founded on piles as opposed to structures on footings or mats. Therefore, should a pile cap fail or move, the adverse consequence of this is often drastic, as the piled structure has little freedom to transfer its need for support to other foundation units. Consequently, it becomes important to assure the design of piled foundations. In many, maybe in most instances, the static pile loading test is routine and geared toward determining an at least capacity, only. However, in these times there is an ever increasing liability of the professional, demands for increased economy of the foundation, and frequent lack of the involvement in the test of the experienced old-timer exercising good judgment. Furthermore, modern pile design is leaving the single, simple concept of capacity and requires more information from the test to assist in determining aspects of long-term behavior and settlement. Therefore, even the straight forward, routine static loading test requires improved planning, execution, and analysis.

Jan 1, 1990

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By Dale E. Berner

A new navigation dam at Olmsted on the Ohio River will be built "in-the-wet" using a lift-in construction method by the Washington Group/Alberici Joint Venture for the U.S. Army Corps of Engineers, Louisville District. Up to 4,000-ton precast concrete dam shell segments will be prefabricated on the Illinois riverbank and lowered into the river on a marine skidway and cradle. A 4,500-ton capacity catamaran crane barge will lift the precast concrete shells and lifting frames from the cradle, and transport them partially submerged to a piled foundation pre-installed underwater. Tremie concrete will be used to compositely connect the shells, piles and sheet pile cut-off walls. This paper focuses on the pipe-pile foundations for this half-mile long navigation dam, and for the temporary precast yard and marine skidway. The dam foundations are designed to resist large ground motions from the New Madrid Fault Zone, and selected production piles are designed to serve as landing piles to support the shells during the construction process. Specific foundation issues addressed in the paper include: pile load tests; production field testing requirements; controlled fixity 24-inch diameter pipe-pile design including seismic considerations; cut-off wall design; sheet pile cellular fixed weir design; isolation jOint design; and temporary works foundation designs for both the precast yard and the marine skidway, including testing of 42-in diameter pipe piles.

May 11, 2007

Jan 1, 2003

By Chandramohan P. V., Ravi Kishore

"An underground reservoir was to be constructed at Doha in Qatar. Simsima lime stone is present at the bottom. When the reservoir is empty, there will be uplift at the bottom but this will change to downward load when it is full. The rock at the bottom had high bearing capacity to resist downward load. But uplift had to be resisted by piles or anchors. The reservoir has a size of 120mx80m. Shrinkage and creep of concrete coupled with thermal contraction imposed a horizontal movement of 26mm on the extreme piles. So, piles have to accommodate this as well. This unique situation needed a unique solution. The solution was to provide piles with flexible high tensile strands to take tension. An annular space near the head of the pile would facilitate horizontal movement as well. Compression load was directly passed on to the raft bearing on rock.INTRODUCTIONAn underground reservoir for storage of drinking water was to be constructed at Doha, Qatar. The reservoir was proposed to have a plan size of 120m x 80m. Clear height inside the reservoir was proposed as 17.2m, from the bottom of roof to the top of bottom raft. Overall height of the reservoir at the outlet from the top of the roof to the bottom of raft was to be 21.2m. For the sake of inspection and in order to prevent pollution from the surroundings a gallery was planned around the reservoir. This could accommodate pipelines as well. This gallery was 3.0m wide on three sides and 8.4m wide on the outlet side.The gallery had removable gratings as cover in order to facilitate maintenance. Capacity of the reservoirwas proposed to be 40million gallons. The reservoir is divided into four compartments with baffle walls in each one for water circulation. Roof of the reservoir is kept at 300mm above ground level. There are two levels of car park on top of the reservoir. Top of the reservoir roof is at +14.35. Bottom varies from - 6.68 to -7.08. Lowest water table is at +6.00. Concrete structure of the reservoir was designed by a local consultant. The Navayuga Engineering Company was entrusted with the construction. Please see Figs 1 and 2."

Jan 1, 2017

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By M. Melih Demirkan, Juan J. Gutierrez, Raghav Ramanathan

"As the capital of the United Arab Emirates (UAE), Abu Dhabi is one of the world’s fastest-developing cities. To sustain its significant growth rate, Abu Dhabi must surmount challenging engineering problems in the most efficient manner. One of the challenges facing Abu Dhabi is ground settlement caused by poor groundwater control practices in inherently difficult subsurface conditions. For construction projects in Abu Dhabi located near the Arabian Gulf, groundwater is frequently encountered and must be accounted for and addressed during design and construction. Abu Dhabi City CenterRecently, the Abu Dhabi government developed a geodatabase by digitizing, processing and qualifying an extensive amount of existing information (i.e., more than 26,000 borehole logs). Because of the evaluation and processing of the geodatabase, detailed maps of geotechnical and hydrogeological surface features were generated using 3D modeling. Ultimately, the geodatabase was used to develop risk maps indicating geohazards, such as sabhka (or salt flats), uncontrolled fill and cavities. This information identifies the location and extent of the areas vulnerable to surface subsidence. Dewatering can change pore water pressure, which, in turn, alters the effective vertical stress in a soil mass and can affect groundwater chemistry. Changes in pore water pressure and groundwater chemistry can significantly affect soil and rock. The potential effects of dewatering include:• Change in effective stresses and shear strengths in soils• Increase in seepage velocities and pressures• Erosion or transport of soil particles and piping• Settlement• Collapse of subsurface cavities or voids• Transport of groundwater containing contaminants• Dissolution of soluble materials, such as rock salt or gypsum"

Jan 1, 2017

By Karen J. Dawson, Francisco Johnson

"Pressure-grouted high strength helical displacement piles are a recently developed pile type that can be useful in conditions where noise or vibrations must be low or where access or clearance is limited. However, there is no information in the literature that can be used to estimate the soil resistance of these piles or production rates. To fill this information need, this paper presents a New Jersey installation case history and the results of static axial and lateral load tests on both pressure-grouted and ungrouted high strength helical piles at the case history site and trial installation locations in New Jersey and Washington State. Piles between 25 and 50 feet long comprised of steel shaft diameters of 4.5, 5.5, and 7 inches with equivalent grout column diameters ranging from 12 to 22 inches were tested. Lateral loads of up to 100 kips and axial compression loads of up to 700 kips were applied. The results of the load tests are compared to predictions of lateral deformation and axial resistance.INTRODUCTIONHelical piles have long been recognized as a useful foundation type in situations where noise and vibrations must be limited, or where there are access or clearance restrictions. Relatively well-documented design methods and torque to capacity correlations have been developed for the most commonly used helical piles, which are relatively small (typically shafts of 6 inches or less) with corresponding low load carrying resistance.With the increased need to construct in congested urban environments, there is incentive to develop helical piles with higher axial resistance. Seismic and other loading conditions also require lateral resistance, which is low for the typically small helical pile shafts. One method of increasing the soil resistance, both axially and laterally and at relatively low cost, is to place grout around the shaft. Injecting the grout under pressure through the hollow helical pipe section and out a grout port or ports located near the toe of the pile has the potential to increase the pile resistance significantly above that which can be achieve by gravity grouting. Not only does the pressurized grout push out against the surrounding soil, but the rotating helix helps to distribute the grout laterally. Unfortunately, little information is available in the literature to help designers estimate the resistance of grouted helical piles in general and none is available regarding pressuregrouted helical piles."

Jan 1, 2016

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Reda Mikhail, M. Birkan Bayrak

The Washington State Department of Transportation (WSDOT) State Route (SR) 167/70th Avenue East Vicinity Bridge Replacement Design-Build project is located in Fife, Washington. This $40 million project consists of replacing the existing 70th Avenue Bridge over Interstate 5 (I-5) with a single-span bridge of about 220 feet long with approach embankments. The subsurface conditions along the new bridge alignment generally consists of alluvial deposits with high potential of liquefaction overlying glacially overridden deposits. In the early stages of the project, drilled shafts were considered as the deep foundation system; however, after an additional subsurface investigation is completed at the site, driven pipe piles were selected as the deep foundation system. Bridge abutments are supported by 24-inch diameter, 80-foot-long open-end driven steel pipe piles. The pile length was determined to bypass a relatively thick liquefiable zone and to tip the piles above what could be compressible soils. The use of advanced seismic analysis was instrumental in optimizing the pile length. The dynamic testing performed on numerous piles indicated what could be unique soil setup factors compared to those measured in local projects as well as those reported in national design manuals. Detailed discussions of the pile foundations design and construction is presented in this paper.

Sep 8, 2021

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polyproplene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2003

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polypropylene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2005

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By WenJun Dong

This paper presents the stability assessment of the steel pipe piles that are used to support a deadman beam to anchor an adjacent bulkhead wall. Finite element analyses are performed to assess the stability of the bulkhead wall and determine the required tie-back force to the pile. The piles are relatively close to the bulkhead wall such that their soil resistance wedge zones are not fully developed but truncated by the bulkhead wall. The reduced lateral resistance capacity of the anchor piles is determined by applying the Coulomb wedge method on the truncated soil passive zones between the pile and wall. Both the conventional soldier pile stability (in terms of force and moment equilibrium) and Winkler soil spring (for soil-pile-interaction) analyses are used to assess the stability of the anchor piles.

Sep 8, 2021